ATA 186 upgrade from SCCP to SIP

Unanswered Question
Dec 18th, 2012
User Badges:

                   I am trying to upgrade ata 186 from sccp to sip, below are current details. I am following below doc


http://www.cisco.com/univercd/cc/td/doc/product/voice/ata/ataadmn/sccp3_0/sccpaapl.htm


to upgrade however, i placed .zup and ata.cnf file at root of tftp but when i reload ata its not even contacting tftp. I have tftp option set to CM 7.1  ip add running on my VM.


any body has done this recently ??




Version: v3.1.0 atasccp (Build 040305B)

DHCP Assigned: IP[192.168.1.9] Subnet[255.255.255.0] Route[192.168.1.1]

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 3 (1 ratings)
Loading.
satish rawat Sat, 12/22/2012 - 10:24
User Badges:

I gave up on this for sometime but i finally managed to upgrade and i am glad to share the procedure here for all those who are looking to do same thing but finds its difficult..its not a commonly used device but very handy at times...


In the begining i was trying to upgrade ata sccp 3.1.0 to sip 3.2 and it never worked so after doing a lot of reading and searching through forums i thought about using a lower version and it paid off.


Procedure:


I had my ATA 186 (sccp ) connected on my internal home network on netgear wireless router so it was on internal dhcp server to get the ip address, my laptop was also connected on same network. First thing i had to do was access ata through web http://x.x.x.x/dev where x.x.x.x is ip address of ATA.


next you have to create a ata configuration file using procedure explained below


http://www.cisco.com/univercd/cc/td/doc/product/voice/ata/ataadmn/sccp3_0/sccpach3.htm#wp1107755


here is out put from a sample config file, note that the parameter upgrade code is very important as it tells the ATA about firmware


#txt

UIPassword:0

UseTftp:1

TftpURL:192.168.1.10

EncryptKey:0

upgradecode:3,0x301,0x0400,0x0200,192.168.1.8,69,0x050616a,ATA030201SIP050616A.zup

upgradelang:0,0x301,0x0400,0x0200,0.0.0.0,69,0,none

Dhcp:1

StaticIp:0

StaticRoute:0

StaticNetMask:0

DNS1IP:0.0.0.0

DNS2IP:0.0.0.0

VLANSetting:0x0000002b

CA0orCM0:0

CA1orCM1:0

CA0UID:0

CA1UID:0

EPID0orSID0:.

EPID1orSID1:.

PrfCodec:1

LBRCodec:3

MediaPort:16384

Domain:0

AudioMode:0x00350035

NumTxFrames:2

CallerIdMethod:0x00019e60

Polarity:0

FXSInputLevel:-1

FXSOutputLevel:-4

ConnectMode:0x90000400

SigTimer:0x00000064

OpFlags:0x2

TOS:0xA0

DialTone:2,31538,30831,1380,1740,1,0,0,1000

DialTone2:2,29780,30743,1252,1384,1,0,0,1000

BusyTone:2,30467,28959,1191,1513,0,4000,4000,0

ReorderTone:2,30467,28959,1191,1513,0,2000,2000,0

RingBackTone:2,30831,30467,1943,2111,0,16000,32000,0

CallWaitTone:1,30831,0,5493,0,0,2400,2400,4800

AlertTone:1,30467,0,5970,0,0,480,480,1920

NPrintf:0

TraceFlags:0x00000000

SyslogIP:0.0.0.0.514

SyslogCtrl:0x00000000


next you will have to run cfgmft tool to generate binaray files. Here is the procedure to do this


http://www.cisco.com/univercd/cc/td/doc/product/voice/ata/ataadmn/sccp3_0/sccpach3.htm#wp1107755


replace sccp with sip in the command.

Emmanuel Valdez Sat, 12/22/2012 - 21:49
User Badges:
  • Bronze, 100 points or more

Hi Satish,


Thanks for sharing your knowledge.


Regards.

Actions

This Discussion