Not able to get DHCP IP via 2504 WLAN Controller

Answered Question
Jan 8th, 2013

Hi,

I have a Cisco Wlan Controller 2504 with 1042N AP (3-nos) every thing was working fine from past 2 months. Now i am getting a issue with clients which are connected to the wireless AP, they are not able to get an dhcp IP address from the 2960 Switch (DHCP Server). The clients are getting IP address as 0.0.0.0.

This is My Configuration:

System Information

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.0.220.0

Bootloader Version............................... 1.0.16

Field Recovery Image Version..................... 1.0.0

Firmware Version................................. PIC 16.0

Build Type....................................... DATA + WPS

System Name...................................... WLAN

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1279

IP Address....................................... 192.168.0.7

Last Reset....................................... Power on reset

System Up Time................................... 0 days 2 hrs 23 mins 22 secs

System Timezone Location.........................

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

Switch Configuration

802.3x Flow Control Mode......................... Disable

FIPS prerequisite features....................... Disabled

secret obfuscation............................... Enabled

                                                         Strong Password Check Features:

         case-check ...........Enabled

         consecutive-check ....Enabled

         default-check .......Enabled

         username-check ......Enabled

Press Enter to continue or <ctrl-z> to abort

Network Information

RF-Network Name............................. MEC

Web Mode.................................... Disable

Secure Web Mode............................. Enable

Secure Web Mode Cipher-Option High.......... Disable

Secure Web Mode Cipher-Option SSLv2......... Enable

OCSP........................................ Disabled

OCSP responder URL..........................

Secure Shell (ssh).......................... Enable

Telnet...................................... Disable

Ethernet Multicast Forwarding............... Disable

Ethernet Broadcast Forwarding............... Disable

AP Multicast/Broadcast Mode................. Multicast   Address : 0.0.0.0

IGMP snooping............................... Disabled

IGMP timeout................................ 60 seconds

IGMP Query Interval......................... 20 seconds

User Idle Timeout........................... 300 seconds

ARP Idle Timeout............................ 300 seconds

Cisco AP Default Master..................... Disable

AP Join Priority............................ Disable

Mgmt Via Wireless Interface................. Disable

Mgmt Via Dynamic Interface.................. Disable

Please Help !!!

I have this problem too.
0 votes
Correct Answer by kcnajaf@25070 about 1 year 3 months ago

Hi,

Use only Key Index 1.

Try creating an new SSID or may be make this SSID itself for testing with open authetication (Security None) and verify if the DHCP works.

Regards

Najaf

  • 1
  • 2
  • 3
  • 4
  • 5
Average Rating: 5 (2 ratings)
Stephen Rodriguez Tue, 01/08/2013 - 07:31

Ok, so:

1.) is the scope exhausted on the 2960?

2.) what has changed recently?

3.) is dhcp proxy enabled or disabled?

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

amankhang Tue, 01/08/2013 - 08:23

1.) is the scope exhausted on the 2960?

-No Its working fine, the pc's which are connected to the switch they are able to get DHCP IP.

2.) what has changed recently?

-Nothing has changed.

3.) is dhcp proxy enabled or disabled?

-i checked it in the WLAN its enabled in it (If u are asking to check in WLAN)

Please still dind got any thing to get it working...

Stephen Rodriguez Tue, 01/08/2013 - 08:42

Proxy would either be Controller > Advanced or show dhcp proxy.

So you have only the one WLAN/interface?

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

Scott Fella Tue, 01/08/2013 - 08:35

You try to delete the DHCP scope and add it back? The switch might be the issue. I have seen it before.

Sent from Cisco Technical Support iPhone App

amankhang Tue, 01/08/2013 - 20:22

Tried deleting the DHCP scope on the switch and checked out still the issue is same..

kcnajaf@25070 Tue, 01/08/2013 - 21:33

Hi Amanulla,

Hope your WLC is configured as Trunk Interface, Please ensure that DHCP VLAN is allowed on the Trunk Links to the WLC and on all the path between WLC and DHCP switch.Also hope you dont have any interface which is configured on WLC with 0.0.0.0 address.

Regards

Najaf

Please rate when applicable or helpful !!!

amankhang Tue, 01/08/2013 - 21:36

yes it is a Trunking between the WLAN interface and to the Switch were it is connected...

I had removed the DHCP cope from the switch and configured on the router...

And rebooted the WLAN controller and NOW ! i am not getting the wifi SSID.

Please help on this !!!

kcnajaf@25070 Tue, 01/08/2013 - 21:39

Sorry,

You mean you are not able to view SSID on the wireless device? Is the SSID broadcasted? Can you get the configuration from WLC please?

Regards

Najaf

amankhang Tue, 01/08/2013 - 21:47

sorry, checked the broadcast SSID was uncheck and found the SSID.

But still not able to get the DHCP Ip address for the wifi clients

amankhang Tue, 01/08/2013 - 21:51

How to set the DHCP Server Ip address in the WLAN controller.

If i check that show dhcp proxy status i can see that the dhcp server is having the Ip address of the switch which was configured previously. but now the DHCP scope is on router and how can i change it to that ?

amankhang Tue, 01/08/2013 - 22:14

Changed to the correct DHCP IP address and rebooted the Controller also..

But still clients are not getting the DHCP IP address.. froan  the router..

Sholud the DHCP proxy should be enabled or disabled on the WLAN controller, if i am using external DHCP Server..

or

Can i enable DHCP pool in the WLAN only for the Clients who connect to the wifi..  from the IP address which are not in the router DHCP pool (Excluded Ip address).. ?

amankhang Tue, 01/08/2013 - 22:28

i get the following when i do sho dhcp stats

DHCP Server IP Address:.......................... 192.168.0.1

  DHCP DISCOVER Count:........................... 48

  DHCP REQUEST Count:............................ 0

  DHCP INFORM Count:............................. 0

  DHCP DECLINE Count:............................ 0

  DHCP RELEASE Count:............................ 0

  DHCP REPLY Count:.............................. 0

  DHCP OFFER Count:.............................. 48

  DHCP ACK Count:................................ 0

  DHCP NAK Count:................................ 0

  Tx Fails:...................................... 0

  Last Rx Time:.................................. 34 seconds ago

  Last Tx Time:.................................. 34 seconds ago

Scott Fella Tue, 01/08/2013 - 22:36

Can you post your show run-config

Sent from Cisco Technical Support iPhone App

amankhang Tue, 01/08/2013 - 22:53

find the Show run-config

(Cisco Controller) >show run-config

Press Enter to continue...

System Inventory

NAME: "Chassis"    , DESCR: "Cisco 2500 Series Wireless LAN Controller"

PID: AIR-CT2504-K9,  VID: V01,  SN: PSJ1623093K

Burned-in MAC Address............................ F4:7F:35:B7:70:20

Maximum number of APs supported.................. 5

Press Enter to continue or to abort

System Information

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.0.220.0

Bootloader Version............................... 1.0.16

Field Recovery Image Version..................... 1.0.0

Firmware Version................................. PIC 16.0

Build Type....................................... DATA + WPS

System Name...................................... IMEC-WLAN

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1279

IP Address....................................... 192.168.0.7

Last Reset....................................... Software reset

System Up Time................................... 0 days 0 hrs 10 mins 25 secs

System Timezone Location.........................

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

--More or (q)uit current module or to abort

Next Boot License Type........................... Permanent

Configured Country............................... US  - United States

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +26 C

External Temperature............................. +31 C

Fan Status....................................... 4300 rpm

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Enabled

Number of WLANs.................................. 1

Number of Active Clients......................... 3

Burned-in MAC Address............................ F4:7F:35:B7:70:20

Maximum number of APs supported.................. 5

Press Enter to continue or to abort

AP Bundle Information

Primary AP ImageSize

--------------------

ap3g15792

ap8015192

ap8025232

c11003084

c11304964

c11404992

c12003364

c12404812

c12505504

c13103136

c15206404

c32014324

c602i3716

Secondary AP ImageSize

----------------------

ap3g15792

ap8015192

--More or (q)uit current module or to abort

ap8025232

c11003084

c11304964

c11404992

c12003364

c12404812

c12505504

c13103136

c15206404

c32014324

c602i3716

Press Enter to continue or to abort

Switch Configuration

802.3x Flow Control Mode......................... Disable

FIPS prerequisite features....................... Disabled

secret obfuscation............................... Enabled

Strong Password Check Features:

case-check ...........Enabled

consecutive-check ....Enabled

default-check .......Enabled

username-check ......Enabled

Press Enter to continue or to abort

Network Information

RF-Network Name............................. IMEC

Web Mode.................................... Disable

Secure Web Mode............................. Enable

Secure Web Mode Cipher-Option High.......... Disable

Secure Web Mode Cipher-Option SSLv2......... Enable

OCSP........................................ Disabled

OCSP responder URL..........................

Secure Shell (ssh).......................... Enable

Telnet...................................... Disable

Ethernet Multicast Forwarding............... Disable

Ethernet Broadcast Forwarding............... Disable

AP Multicast/Broadcast Mode................. Multicast   Address : 0.0.0.0

IGMP snooping............................... Disabled

IGMP timeout................................ 60 seconds

IGMP Query Interval......................... 20 seconds

User Idle Timeout........................... 300 seconds

ARP Idle Timeout............................ 300 seconds

Cisco AP Default Master..................... Disable

AP Join Priority............................ Disable

Mgmt Via Wireless Interface................. Disable

Mgmt Via Dynamic Interface.................. Disable

--More or (q)uit current module or to abort

Bridge MAC filter Config.................... Enable

Bridge Security Mode........................ EAP

Mesh Full Sector DFS........................ Enable

AP Fallback ................................ Enable

Web Auth Redirect Ports .................... 80

Web Auth Proxy Redirect  ................... Disable

Fast SSID Change ........................... Disabled

IP/MAC Addr Binding Check .................. Enabled

Press Enter to continue or to abort

Port Summary

           STP   Admin   Physical   Physical   Link   Link

Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE 

-- ------- ---- ------- ---------- ---------- ------ ------- -------

1  Normal  Forw Enable  Auto       1000 Full  Up     Enable  N/A    

2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A    

3  Normal  Disa Enable  Auto       Auto       Down   Enable  Enable  (Power Off)

4  Normal  Disa Enable  Auto       Auto       Down   Enable  Enable  (Power Off)

Press Enter to continue or to abort

AP Summary

Number of APs.................................... 3

Global AP User Name.............................. Not Configured

Global AP Dot1x User Name........................ Not Configured

AP Name             Slots  AP Model              Ethernet MAC       Location          Port  Country  Priority

------------------  -----  --------------------  -----------------  ----------------  ----  -------  ------

IMEC-AP2             2     AIR-LAP1042N-N-K9     ac:f2:c5:f3:ea:32  default location  1        US       1

IMEC-AP3             2     AIR-LAP1042N-N-K9     ac:f2:c5:f2:78:c2  default location  1        US       1

IMEC-AP1             2     AIR-LAP1042N-N-K9     ac:f2:c5:f3:ee:16  default location  1        US       1

AP Tcp-Mss-Adjust Info

AP Name              TCP State  MSS Size

------------------   --------   -------

IMEC-AP2             disabled   -

IMEC-AP3             disabled   -

IMEC-AP1             disabled   -

Press Enter to continue or to abort

AP Location

Total Number of AP Groups........................ 0   

Site Name........................................ default-group

Site Description.................................

WLAN ID          Interface          Network Admission Control          Radio Policy

-------          -----------        --------------------------         ------------

1               management           Disabled                          None

AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority

------------------  -----  -------------------  -----------------  ----------------  ----  -------  --------

IMEC-AP2             2     AIR-LAP1042N-N-K9    ac:f2:c5:f3:ea:32  default location  1     US       1

IMEC-AP3             2     AIR-LAP1042N-N-K9    ac:f2:c5:f2:78:c2  default location  1     US       1

IMEC-AP1             2     AIR-LAP1042N-N-K9    ac:f2:c5:f3:ee:16  default location  1     US       1

Press Enter to continue or to abort

AP Config

Cisco AP Identifier.............................. 0

Cisco AP Name.................................... IMEC-AP2

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -A

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f3:ea:32

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.9

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

--More or (q)uit current module or to abort

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

--More or (q)uit current module or to abort

AP Model......................................... AIR-LAP1042N-N-K9  

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52Q

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 01 h 07 m 47 s

AP LWAPP Up Time................................. 0 days, 00 h 09 m 27 s

Join Date and Time............................... Wed Jan  9 12:12:27 2013

Join Taken Time.................................. 0 days, 00 h 01 m 33 s

Attributes for Slot  0

    Radio Type................................... RADIO_TYPE_80211n-2.4

    Administrative State ........................ ADMIN_ENABLED

    Operation State ............................. UP

    Radio Role .................................. ACCESS

    CellId ...................................... 0

--More or (q)uit current module or to abort

    Station Configuration

      Configuration ............................. AUTOMATIC

      Number Of WLANs ........................... 1

      Medium Occupancy Limit .................... 100

      CFP Period ................................ 4

      CFP MaxDuration ........................... 60

      BSSID ..................................... cc:d5:39:d0:bf:80

      Operation Rate Set

        1000 Kilo Bits........................... MANDATORY

        2000 Kilo Bits........................... MANDATORY

        5500 Kilo Bits........................... MANDATORY

        11000 Kilo Bits.......................... MANDATORY

        6000 Kilo Bits........................... SUPPORTED

        9000 Kilo Bits........................... SUPPORTED

        12000 Kilo Bits.......................... SUPPORTED

        18000 Kilo Bits.......................... SUPPORTED

        24000 Kilo Bits.......................... SUPPORTED

        36000 Kilo Bits.......................... SUPPORTED

        48000 Kilo Bits.......................... SUPPORTED

        54000 Kilo Bits.......................... SUPPORTED

      MCS Set

        MCS 0.................................... SUPPORTED

--More or (q)uit current module or to abort

        MCS 1.................................... SUPPORTED

        MCS 2.................................... SUPPORTED

        MCS 3.................................... SUPPORTED

        MCS 4.................................... SUPPORTED

        MCS 5.................................... SUPPORTED

        MCS 6.................................... SUPPORTED

        MCS 7.................................... SUPPORTED

        MCS 8.................................... SUPPORTED

        MCS 9.................................... SUPPORTED

        MCS 10................................... SUPPORTED

        MCS 11................................... SUPPORTED

        MCS 12................................... SUPPORTED

        MCS 13................................... SUPPORTED

        MCS 14................................... SUPPORTED

        MCS 15................................... SUPPORTED

      Beacon Period ............................. 100

      Fragmentation Threshold ................... 2346

      Multi Domain Capability Implemented ....... TRUE

      Multi Domain Capability Enabled ........... TRUE

      Country String ............................ US

    Multi Domain Capability

      Configuration ............................. AUTOMATIC

--More or (q)uit current module or to abort

      First Chan Num ............................ 1

      Number Of Channels ........................ 11

    MAC Operation Parameters

      Configuration ............................. AUTOMATIC

      Fragmentation Threshold ................... 2346

      Packet Retry Limit ........................ 64

    Tx Power

      Num Of Supported Power Levels ............. 8

      Tx Power Level 1 .......................... 20 dBm

      Tx Power Level 2 .......................... 17 dBm

      Tx Power Level 3 .......................... 14 dBm

      Tx Power Level 4 .......................... 11 dBm

      Tx Power Level 5 .......................... 8 dBm

      Tx Power Level 6 .......................... 5 dBm

      Tx Power Level 7 .......................... 2 dBm

      Tx Power Level 8 .......................... -1 dBm

      Tx Power Configuration .................... AUTOMATIC

      Current Tx Power Level .................... 1

    Phy OFDM parameters

      Configuration ............................. AUTOMATIC

--More or (q)uit current module or to abort

      Current Channel ........................... 1

      Extension Channel ......................... NONE

      Channel Width.............................. 20 Mhz

      Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11

      TI Threshold .............................. -50

      Legacy Tx Beamforming Configuration ....... AUTOMATIC

      Legacy Tx Beamforming ..................... DISABLED

      Antenna Type............................... INTERNAL_ANTENNA

      Internal Antenna Gain (in .5 dBi units).... 8

      Diversity.................................. DIVERSITY_ENABLED

      802.11n Antennas

         A....................................... ENABLED

         B....................................... ENABLED

         C....................................... DISABLED

    Performance Profile Parameters

      Configuration ............................. AUTOMATIC

      Interference threshold..................... 10 %

      Noise threshold............................  -70 dBm

      RF utilization threshold................... 80 %

      Data-rate threshold........................ 1000000 bps

      Client threshold........................... 12 clients

      Coverage SNR threshold..................... 12 dB

--More or (q)uit current module or to abort

      Coverage exception level................... 25 %

      Client minimum exception level............. 3 clients

    Rogue Containment Information

    Containment Count............................ 0

    CleanAir Management Information

        CleanAir Capable......................... No

Cisco AP Identifier.............................. 0

Cisco AP Name.................................... IMEC-AP2

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -N

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f3:ea:32

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.9

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

--More or (q)uit current module or to abort

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

--More or (q)uit current module or to abort

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

AP Model......................................... AIR-LAP1042N-N-K9  

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52Q

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 01 h 07 m 47 s

AP LWAPP Up Time................................. 0 days, 00 h 09 m 27 s

Join Date and Time............................... Wed Jan  9 12:12:27 2013

Join Taken Time.................................. 0 days, 00 h 01 m 33 s

--More or (q)uit current module or to abort

Attributes for Slot  1

    Regulatory Domain check for this slot has Failed. This slot will not be operational

Press Enter to continue or to abort

Cisco AP Identifier.............................. 1

Cisco AP Name.................................... IMEC-AP3

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -A

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f2:78:c2

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.10

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

Primary Cisco Switch IP Address.................. Not Configured

--More or (q)uit current module or to abort

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

AP Model......................................... AIR-LAP1042N-N-K9  

--More or (q)uit current module or to abort

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52P

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 01 h 07 m 56 s

AP LWAPP Up Time................................. 0 days, 00 h 09 m 32 s

Join Date and Time............................... Wed Jan  9 12:12:31 2013

Join Taken Time.................................. 0 days, 00 h 01 m 40 s

Attributes for Slot  0

    Radio Type................................... RADIO_TYPE_80211n-2.4

    Administrative State ........................ ADMIN_ENABLED

    Operation State ............................. UP

    Radio Role .................................. ACCESS

    CellId ...................................... 0

--More or (q)uit current module or to abort

    Station Configuration

      Configuration ............................. AUTOMATIC

      Number Of WLANs ........................... 1

      Medium Occupancy Limit .................... 100

      CFP Period ................................ 4

      CFP MaxDuration ........................... 60

      BSSID ..................................... cc:d5:39:d0:c8:70

      Operation Rate Set

        1000 Kilo Bits........................... MANDATORY

        2000 Kilo Bits........................... MANDATORY

        5500 Kilo Bits........................... MANDATORY

        11000 Kilo Bits.......................... MANDATORY

        6000 Kilo Bits........................... SUPPORTED

        9000 Kilo Bits........................... SUPPORTED

        12000 Kilo Bits.......................... SUPPORTED

        18000 Kilo Bits.......................... SUPPORTED

        24000 Kilo Bits.......................... SUPPORTED

        36000 Kilo Bits.......................... SUPPORTED

        48000 Kilo Bits.......................... SUPPORTED

        54000 Kilo Bits.......................... SUPPORTED

      MCS Set

        MCS 0.................................... SUPPORTED

        MCS 1.................................... SUPPORTED

--More or (q)uit current module or to abort

(Cisco Controller) >logout

Scott Fella Tue, 01/08/2013 - 23:01

I don't see your WLAN config nor your interface config

Sent from Cisco Technical Support iPhone App

Scott Fella Tue, 01/08/2013 - 23:03

Can you do config paging disable then issue the show run-config no-ap and save that to a text file and attach it. Don't paste it into the thread.

Sent from Cisco Technical Support iPhone App

amankhang Tue, 01/08/2013 - 23:09

find this

(Cisco Controller) >show run-config

Press Enter to continue...

System Inventory

NAME: "Chassis"    , DESCR: "Cisco 2500 Series Wireless LAN Controller"

PID: AIR-CT2504-K9,  VID: V01,  SN: PSJ1623093K

Burned-in MAC Address............................ F4:7F:35:B7:70:20

Maximum number of APs supported.................. 5

System Information

Manufacturer's Name.............................. Cisco Systems Inc.

Product Name..................................... Cisco Controller

Product Version.................................. 7.0.220.0

Bootloader Version............................... 1.0.16

Field Recovery Image Version..................... 1.0.0

Firmware Version................................. PIC 16.0

Build Type....................................... DATA + WPS

System Name...................................... IMEC-WLAN

System Location..................................

System Contact...................................

System ObjectID.................................. 1.3.6.1.4.1.9.1.1279

IP Address....................................... 192.168.0.7

Last Reset....................................... Software reset

System Up Time................................... 0 days 0 hrs 9 mins 21 secs

System Timezone Location.........................

Current Boot License Level....................... base

Current Boot License Type........................ Permanent

Next Boot License Level.......................... base

Next Boot License Type........................... Permanent

Configured Country............................... US  - United States

Operating Environment............................ Commercial (0 to 40 C)

Internal Temp Alarm Limits....................... 0 to 65 C

Internal Temperature............................. +26 C

External Temperature............................. +32 C

Fan Status....................................... 4300 rpm

State of 802.11b Network......................... Enabled

State of 802.11a Network......................... Enabled

Number of WLANs.................................. 1

Number of Active Clients......................... 2

Burned-in MAC Address............................ F4:7F:35:B7:70:20

Maximum number of APs supported.................. 5

AP Bundle Information

Primary AP ImageSize

--------------------

ap3g15792

ap8015192

ap8025232

c11003084

c11304964

c11404992

c12003364

c12404812

c12505504

c13103136

c15206404

c32014324

c602i3716

Secondary AP ImageSize

----------------------

ap3g15792

ap8015192

ap8025232

c11003084

c11304964

c11404992

c12003364

c12404812

c12505504

c13103136

c15206404

c32014324

c602i3716

Switch Configuration

802.3x Flow Control Mode......................... Disable

FIPS prerequisite features....................... Disabled

secret obfuscation............................... Enabled

Strong Password Check Features:

case-check ...........Enabled

consecutive-check ....Enabled

default-check .......Enabled

username-check ......Enabled

Network Information

RF-Network Name............................. IMEC

Web Mode.................................... Disable

Secure Web Mode............................. Enable

Secure Web Mode Cipher-Option High.......... Disable

Secure Web Mode Cipher-Option SSLv2......... Enable

OCSP........................................ Disabled

OCSP responder URL..........................

Secure Shell (ssh).......................... Enable

Telnet...................................... Disable

Ethernet Multicast Forwarding............... Disable

Ethernet Broadcast Forwarding............... Disable

AP Multicast/Broadcast Mode................. Multicast   Address : 0.0.0.0

IGMP snooping............................... Disabled

IGMP timeout................................ 60 seconds

IGMP Query Interval......................... 20 seconds

User Idle Timeout........................... 300 seconds

ARP Idle Timeout............................ 300 seconds

Cisco AP Default Master..................... Disable

AP Join Priority............................ Disable

Mgmt Via Wireless Interface................. Disable

Mgmt Via Dynamic Interface.................. Disable

Bridge MAC filter Config.................... Enable

Bridge Security Mode........................ EAP

Mesh Full Sector DFS........................ Enable

AP Fallback ................................ Enable

Web Auth Redirect Ports .................... 80

Web Auth Proxy Redirect  ................... Disable

Fast SSID Change ........................... Disabled

IP/MAC Addr Binding Check .................. Enabled

Port Summary

           STP   Admin   Physical   Physical   Link   Link

Pr  Type   Stat   Mode     Mode      Status   Status  Trap     POE 

-- ------- ---- ------- ---------- ---------- ------ ------- -------

1  Normal  Forw Enable  Auto       1000 Full  Up     Enable  N/A    

2  Normal  Disa Enable  Auto       Auto       Down   Enable  N/A    

3  Normal  Disa Enable  Auto       Auto       Down   Enable  Enable  (Power Off)

4  Normal  Disa Enable  Auto       Auto       Down   Enable  Enable  (Power Off)

AP Summary

Number of APs.................................... 3

Global AP User Name.............................. Not Configured

Global AP Dot1x User Name........................ Not Configured

AP Name             Slots  AP Model              Ethernet MAC       Location          Port  Country  Priority

------------------  -----  --------------------  -----------------  ----------------  ----  -------  ------

IMEC-AP3             2     AIR-LAP1042N-N-K9     ac:f2:c5:f2:78:c2  default location  1        US       1

IMEC-AP2             2     AIR-LAP1042N-N-K9     ac:f2:c5:f3:ea:32  default location  1        US       1

IMEC-AP1             2     AIR-LAP1042N-N-K9     ac:f2:c5:f3:ee:16  default location  1        US       1

AP Tcp-Mss-Adjust Info

AP Name              TCP State  MSS Size

------------------   --------   -------

IMEC-AP3             disabled   -

IMEC-AP2             disabled   -

IMEC-AP1             disabled   -

AP Location

Total Number of AP Groups........................ 0   

Site Name........................................ default-group

Site Description.................................

WLAN ID          Interface          Network Admission Control          Radio Policy

-------          -----------        --------------------------         ------------

1               management           Disabled                          None

AP Name             Slots  AP Model             Ethernet MAC       Location          Port  Country  Priority

------------------  -----  -------------------  -----------------  ----------------  ----  -------  --------

IMEC-AP3             2     AIR-LAP1042N-N-K9    ac:f2:c5:f2:78:c2  default location  1     US       1

IMEC-AP2             2     AIR-LAP1042N-N-K9    ac:f2:c5:f3:ea:32  default location  1     US       1

IMEC-AP1             2     AIR-LAP1042N-N-K9    ac:f2:c5:f3:ee:16  default location  1     US       1

AP Config

Cisco AP Identifier.............................. 0

Cisco AP Name.................................... IMEC-AP3

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -A

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f2:78:c2

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.10

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

AP Model......................................... AIR-LAP1042N-N-K9  

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52P

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 00 h 04 m 10 s

AP LWAPP Up Time................................. 0 days, 00 h 03 m 14 s

Join Date and Time............................... Wed Jan  9 12:31:35 2013

Join Taken Time.................................. 0 days, 00 h 00 m 55 s

Attributes for Slot  0

    Radio Type................................... RADIO_TYPE_80211n-2.4

    Administrative State ........................ ADMIN_ENABLED

    Operation State ............................. UP

    Radio Role .................................. ACCESS

    CellId ...................................... 0

    Station Configuration

      Configuration ............................. AUTOMATIC

      Number Of WLANs ........................... 1

      Medium Occupancy Limit .................... 100

      CFP Period ................................ 4

      CFP MaxDuration ........................... 60

      BSSID ..................................... cc:d5:39:d0:c8:70

      Operation Rate Set

        1000 Kilo Bits........................... MANDATORY

        2000 Kilo Bits........................... MANDATORY

        5500 Kilo Bits........................... MANDATORY

        11000 Kilo Bits.......................... MANDATORY

        6000 Kilo Bits........................... SUPPORTED

        9000 Kilo Bits........................... SUPPORTED

        12000 Kilo Bits.......................... SUPPORTED

        18000 Kilo Bits.......................... SUPPORTED

        24000 Kilo Bits.......................... SUPPORTED

        36000 Kilo Bits.......................... SUPPORTED

        48000 Kilo Bits.......................... SUPPORTED

        54000 Kilo Bits.......................... SUPPORTED

      MCS Set

        MCS 0.................................... SUPPORTED

        MCS 1.................................... SUPPORTED

        MCS 2.................................... SUPPORTED

        MCS 3.................................... SUPPORTED

        MCS 4.................................... SUPPORTED

        MCS 5.................................... SUPPORTED

        MCS 6.................................... SUPPORTED

        MCS 7.................................... SUPPORTED

        MCS 8.................................... SUPPORTED

        MCS 9.................................... SUPPORTED

        MCS 10................................... SUPPORTED

        MCS 11................................... SUPPORTED

        MCS 12................................... SUPPORTED

        MCS 13................................... SUPPORTED

        MCS 14................................... SUPPORTED

        MCS 15................................... SUPPORTED

      Beacon Period ............................. 100

      Fragmentation Threshold ................... 2346

      Multi Domain Capability Implemented ....... TRUE

      Multi Domain Capability Enabled ........... TRUE

      Country String ............................ US

    Multi Domain Capability

      Configuration ............................. AUTOMATIC

      First Chan Num ............................ 1

      Number Of Channels ........................ 11

    MAC Operation Parameters

      Configuration ............................. AUTOMATIC

      Fragmentation Threshold ................... 2346

      Packet Retry Limit ........................ 64

    Tx Power

      Num Of Supported Power Levels ............. 8

      Tx Power Level 1 .......................... 20 dBm

      Tx Power Level 2 .......................... 17 dBm

      Tx Power Level 3 .......................... 14 dBm

      Tx Power Level 4 .......................... 11 dBm

      Tx Power Level 5 .......................... 8 dBm

      Tx Power Level 6 .......................... 5 dBm

      Tx Power Level 7 .......................... 2 dBm

      Tx Power Level 8 .......................... -1 dBm

      Tx Power Configuration .................... AUTOMATIC

      Current Tx Power Level .................... 1

    Phy OFDM parameters

      Configuration ............................. AUTOMATIC

      Current Channel ........................... 11

      Extension Channel ......................... NONE

      Channel Width.............................. 20 Mhz

      Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11

      TI Threshold .............................. -50

      Legacy Tx Beamforming Configuration ....... AUTOMATIC

      Legacy Tx Beamforming ..................... DISABLED

      Antenna Type............................... INTERNAL_ANTENNA

      Internal Antenna Gain (in .5 dBi units).... 8

      Diversity.................................. DIVERSITY_ENABLED

      802.11n Antennas

         A....................................... ENABLED

         B....................................... ENABLED

         C....................................... DISABLED

    Performance Profile Parameters

      Configuration ............................. AUTOMATIC

      Interference threshold..................... 10 %

      Noise threshold............................  -70 dBm

      RF utilization threshold................... 80 %

      Data-rate threshold........................ 1000000 bps

      Client threshold........................... 12 clients

      Coverage SNR threshold..................... 12 dB

      Coverage exception level................... 25 %

      Client minimum exception level............. 3 clients

    Rogue Containment Information

    Containment Count............................ 0

    CleanAir Management Information

        CleanAir Capable......................... No

Cisco AP Identifier.............................. 0

Cisco AP Name.................................... IMEC-AP3

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -N

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f2:78:c2

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.10

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

AP Model......................................... AIR-LAP1042N-N-K9  

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52P

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 00 h 04 m 10 s

AP LWAPP Up Time................................. 0 days, 00 h 03 m 14 s

Join Date and Time............................... Wed Jan  9 12:31:35 2013

Join Taken Time.................................. 0 days, 00 h 00 m 55 s

Attributes for Slot  1

    Regulatory Domain check for this slot has Failed. This slot will not be operational

Cisco AP Identifier.............................. 1

Cisco AP Name.................................... IMEC-AP2

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -A

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f3:ea:32

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.9

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

AP Model......................................... AIR-LAP1042N-N-K9  

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52Q

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 00 h 02 m 56 s

AP LWAPP Up Time................................. 0 days, 00 h 02 m 00 s

Join Date and Time............................... Wed Jan  9 12:32:50 2013

Join Taken Time.................................. 0 days, 00 h 00 m 55 s

Attributes for Slot  0

    Radio Type................................... RADIO_TYPE_80211n-2.4

    Administrative State ........................ ADMIN_ENABLED

    Operation State ............................. UP

    Radio Role .................................. ACCESS

    CellId ...................................... 0

    Station Configuration

      Configuration ............................. AUTOMATIC

      Number Of WLANs ........................... 1

      Medium Occupancy Limit .................... 100

      CFP Period ................................ 4

      CFP MaxDuration ........................... 60

      BSSID ..................................... cc:d5:39:d0:bf:80

      Operation Rate Set

        1000 Kilo Bits........................... MANDATORY

        2000 Kilo Bits........................... MANDATORY

        5500 Kilo Bits........................... MANDATORY

        11000 Kilo Bits.......................... MANDATORY

        6000 Kilo Bits........................... SUPPORTED

        9000 Kilo Bits........................... SUPPORTED

        12000 Kilo Bits.......................... SUPPORTED

        18000 Kilo Bits.......................... SUPPORTED

        24000 Kilo Bits.......................... SUPPORTED

        36000 Kilo Bits.......................... SUPPORTED

        48000 Kilo Bits.......................... SUPPORTED

        54000 Kilo Bits.......................... SUPPORTED

      MCS Set

        MCS 0.................................... SUPPORTED

        MCS 1.................................... SUPPORTED

        MCS 2.................................... SUPPORTED

        MCS 3.................................... SUPPORTED

        MCS 4.................................... SUPPORTED

        MCS 5.................................... SUPPORTED

        MCS 6.................................... SUPPORTED

        MCS 7.................................... SUPPORTED

        MCS 8.................................... SUPPORTED

        MCS 9.................................... SUPPORTED

        MCS 10................................... SUPPORTED

        MCS 11................................... SUPPORTED

        MCS 12................................... SUPPORTED

        MCS 13................................... SUPPORTED

        MCS 14................................... SUPPORTED

        MCS 15................................... SUPPORTED

      Beacon Period ............................. 100

      Fragmentation Threshold ................... 2346

      Multi Domain Capability Implemented ....... TRUE

      Multi Domain Capability Enabled ........... TRUE

      Country String ............................ US

    Multi Domain Capability

      Configuration ............................. AUTOMATIC

      First Chan Num ............................ 1

      Number Of Channels ........................ 11

    MAC Operation Parameters

      Configuration ............................. AUTOMATIC

      Fragmentation Threshold ................... 2346

      Packet Retry Limit ........................ 64

    Tx Power

      Num Of Supported Power Levels ............. 8

      Tx Power Level 1 .......................... 20 dBm

      Tx Power Level 2 .......................... 17 dBm

      Tx Power Level 3 .......................... 14 dBm

      Tx Power Level 4 .......................... 11 dBm

      Tx Power Level 5 .......................... 8 dBm

      Tx Power Level 6 .......................... 5 dBm

      Tx Power Level 7 .......................... 2 dBm

      Tx Power Level 8 .......................... -1 dBm

      Tx Power Configuration .................... AUTOMATIC

      Current Tx Power Level .................... 1

    Phy OFDM parameters

      Configuration ............................. AUTOMATIC

      Current Channel ........................... 1

      Extension Channel ......................... NONE

      Channel Width.............................. 20 Mhz

      Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11

      TI Threshold .............................. -50

      Legacy Tx Beamforming Configuration ....... AUTOMATIC

      Legacy Tx Beamforming ..................... DISABLED

      Antenna Type............................... INTERNAL_ANTENNA

      Internal Antenna Gain (in .5 dBi units).... 8

      Diversity.................................. DIVERSITY_ENABLED

      802.11n Antennas

         A....................................... ENABLED

         B....................................... ENABLED

         C....................................... DISABLED

    Performance Profile Parameters

      Configuration ............................. AUTOMATIC

      Interference threshold..................... 10 %

      Noise threshold............................  -70 dBm

      RF utilization threshold................... 80 %

      Data-rate threshold........................ 1000000 bps

      Client threshold........................... 12 clients

      Coverage SNR threshold..................... 12 dB

      Coverage exception level................... 25 %

      Client minimum exception level............. 3 clients

    Rogue Containment Information

    Containment Count............................ 0

    CleanAir Management Information

        CleanAir Capable......................... No

Cisco AP Identifier.............................. 1

Cisco AP Name.................................... IMEC-AP2

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -N

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f3:ea:32

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.9

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

AP Model......................................... AIR-LAP1042N-N-K9  

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52Q

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 00 h 02 m 56 s

AP LWAPP Up Time................................. 0 days, 00 h 02 m 00 s

Join Date and Time............................... Wed Jan  9 12:32:50 2013

Join Taken Time.................................. 0 days, 00 h 00 m 55 s

Attributes for Slot  1

    Regulatory Domain check for this slot has Failed. This slot will not be operational

Cisco AP Identifier.............................. 2

Cisco AP Name.................................... IMEC-AP1

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -A

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f3:ee:16

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.8

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

AP Model......................................... AIR-LAP1042N-N-K9  

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52M

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 00 h 01 m 59 s

AP LWAPP Up Time................................. 0 days, 00 h 01 m 03 s

Join Date and Time............................... Wed Jan  9 12:33:48 2013

Join Taken Time.................................. 0 days, 00 h 00 m 55 s

Attributes for Slot  0

    Radio Type................................... RADIO_TYPE_80211n-2.4

    Administrative State ........................ ADMIN_ENABLED

    Operation State ............................. UP

    Radio Role .................................. ACCESS

    CellId ...................................... 0

    Station Configuration

      Configuration ............................. AUTOMATIC

      Number Of WLANs ........................... 1

      Medium Occupancy Limit .................... 100

      CFP Period ................................ 4

      CFP MaxDuration ........................... 60

      BSSID ..................................... cc:d5:39:d1:0c:20

      Operation Rate Set

        1000 Kilo Bits........................... MANDATORY

        2000 Kilo Bits........................... MANDATORY

        5500 Kilo Bits........................... MANDATORY

        11000 Kilo Bits.......................... MANDATORY

        6000 Kilo Bits........................... SUPPORTED

        9000 Kilo Bits........................... SUPPORTED

        12000 Kilo Bits.......................... SUPPORTED

        18000 Kilo Bits.......................... SUPPORTED

        24000 Kilo Bits.......................... SUPPORTED

        36000 Kilo Bits.......................... SUPPORTED

        48000 Kilo Bits.......................... SUPPORTED

        54000 Kilo Bits.......................... SUPPORTED

      MCS Set

        MCS 0.................................... SUPPORTED

        MCS 1.................................... SUPPORTED

        MCS 2.................................... SUPPORTED

        MCS 3.................................... SUPPORTED

        MCS 4.................................... SUPPORTED

        MCS 5.................................... SUPPORTED

        MCS 6.................................... SUPPORTED

        MCS 7.................................... SUPPORTED

        MCS 8.................................... SUPPORTED

        MCS 9.................................... SUPPORTED

        MCS 10................................... SUPPORTED

        MCS 11................................... SUPPORTED

        MCS 12................................... SUPPORTED

        MCS 13................................... SUPPORTED

        MCS 14................................... SUPPORTED

        MCS 15................................... SUPPORTED

      Beacon Period ............................. 100

      Fragmentation Threshold ................... 2346

      Multi Domain Capability Implemented ....... TRUE

      Multi Domain Capability Enabled ........... TRUE

      Country String ............................ US

    Multi Domain Capability

      Configuration ............................. AUTOMATIC

      First Chan Num ............................ 1

      Number Of Channels ........................ 11

    MAC Operation Parameters

      Configuration ............................. AUTOMATIC

      Fragmentation Threshold ................... 2346

      Packet Retry Limit ........................ 64

    Tx Power

      Num Of Supported Power Levels ............. 8

      Tx Power Level 1 .......................... 20 dBm

      Tx Power Level 2 .......................... 17 dBm

      Tx Power Level 3 .......................... 14 dBm

      Tx Power Level 4 .......................... 11 dBm

      Tx Power Level 5 .......................... 8 dBm

      Tx Power Level 6 .......................... 5 dBm

      Tx Power Level 7 .......................... 2 dBm

      Tx Power Level 8 .......................... -1 dBm

      Tx Power Configuration .................... AUTOMATIC

      Current Tx Power Level .................... 1

    Phy OFDM parameters

      Configuration ............................. AUTOMATIC

      Current Channel ........................... 6

      Extension Channel ......................... NONE

      Channel Width.............................. 20 Mhz

      Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11

      TI Threshold .............................. -50

      Legacy Tx Beamforming Configuration ....... AUTOMATIC

      Legacy Tx Beamforming ..................... DISABLED

      Antenna Type............................... INTERNAL_ANTENNA

      Internal Antenna Gain (in .5 dBi units).... 8

      Diversity.................................. DIVERSITY_ENABLED

      802.11n Antennas

         A....................................... ENABLED

         B....................................... ENABLED

         C....................................... DISABLED

    Performance Profile Parameters

      Configuration ............................. AUTOMATIC

      Interference threshold..................... 10 %

      Noise threshold............................  -70 dBm

      RF utilization threshold................... 80 %

      Data-rate threshold........................ 1000000 bps

      Client threshold........................... 12 clients

      Coverage SNR threshold..................... 12 dB

      Coverage exception level................... 25 %

      Client minimum exception level............. 3 clients

    Rogue Containment Information

    Containment Count............................ 0

    CleanAir Management Information

        CleanAir Capable......................... No

Cisco AP Identifier.............................. 2

Cisco AP Name.................................... IMEC-AP1

Country code..................................... US  - United States

Regulatory Domain allowed by Country............. 802.11bg:-A     802.11a:-A

AP Country code.................................. US  - United States

AP Regulatory Domain............................. -N

Switch Port Number .............................. 1

MAC Address...................................... ac:f2:c5:f3:ee:16

IP Address Configuration......................... Static IP assigned

IP Address....................................... 192.168.0.8

IP NetMask....................................... 255.255.255.0

Gateway IP Addr.................................. 192.168.0.1

Domain...........................................

Name Server......................................

NAT External IP Address.......................... None

CAPWAP Path MTU.................................. 1485

Telnet State..................................... Disabled

Ssh State........................................ Disabled

Cisco AP Location................................ default location

Cisco AP Group Name.............................. default-group

Primary Cisco Switch Name........................

Primary Cisco Switch IP Address.................. Not Configured

Secondary Cisco Switch Name......................

Secondary Cisco Switch IP Address................ Not Configured

Tertiary Cisco Switch Name.......................

Tertiary Cisco Switch IP Address................. Not Configured

Administrative State ............................ ADMIN_ENABLED

Operation State ................................. REGISTERED

Mirroring Mode .................................. Disabled

AP Mode ......................................... Local

Public Safety ................................... Disabled

AP SubMode ...................................... Not Configured

Remote AP Debug ................................. Disabled

Logging trap severity level ..................... informational

Logging syslog facility ......................... kern

S/W  Version .................................... 7.0.220.0

Boot  Version ................................... 12.4.23.6

Mini IOS Version ................................ 7.3.1.73

Stats Reporting Period .......................... 180

LED State........................................ Enabled

PoE Pre-Standard Switch.......................... Disabled

PoE Power Injector MAC Addr...................... Disabled

Power Type/Mode.................................. Power injector / Normal mode

Number Of Slots.................................. 2

AP Model......................................... AIR-LAP1042N-N-K9  

AP Image......................................... C1040-K9W8-M

IOS Version...................................... 12.4(23c)JA3

Reset Button..................................... Enabled

AP Serial Number................................. FGL1646S52M

AP Certificate Type.............................. Manufacture Installed

AP User Mode..................................... AUTOMATIC

AP User Name..................................... Not Configured

AP Dot1x User Mode............................... Not Configured

AP Dot1x User Name............................... Not Configured

Cisco AP system logging host..................... 255.255.255.255

AP Up Time....................................... 0 days, 00 h 01 m 59 s

AP LWAPP Up Time................................. 0 days, 00 h 01 m 03 s

Join Date and Time............................... Wed Jan  9 12:33:48 2013

Join Taken Time.................................. 0 days, 00 h 00 m 55 s

Attributes for Slot  1

    Regulatory Domain check for this slot has Failed. This slot will not be operational

AP Airewave Director Configuration

Number Of Slots.................................. 2

AP Name.......................................... IMEC-AP3

MAC Address...................................... ac:f2:c5:f2:78:c2

  Slot ID........................................ 0

  Radio Type..................................... RADIO_TYPE_80211b/g

  Sub-band Type.................................. All

  Noise Information

    Noise Profile................................ PASSED

    Channel 1....................................  -90 dBm

    Channel 2....................................  -93 dBm

    Channel 3....................................  -93 dBm

    Channel 4....................................  -89 dBm

    Channel 5....................................  -89 dBm

    Channel 6....................................  -91 dBm

    Channel 7....................................  -92 dBm

    Channel 8....................................  -93 dBm

    Channel 9....................................  -92 dBm

    Channel 10...................................  -93 dBm

    Channel 11...................................  -88 dBm

  Interference Information

    Interference Profile......................... PASSED

    Channel 1....................................  -81 dBm @  1 % busy

    Channel 2.................................... -128 dBm @  0 % busy

    Channel 3.................................... -128 dBm @  0 % busy

    Channel 4.................................... -128 dBm @  0 % busy

    Channel 5.................................... -128 dBm @  0 % busy

    Channel 6.................................... -128 dBm @  0 % busy

    Channel 7.................................... -128 dBm @  0 % busy

    Channel 8....................................  -75 dBm @  1 % busy

    Channel 9.................................... -128 dBm @  0 % busy

    Channel 10................................... -128 dBm @  0 % busy

    Channel 11................................... -128 dBm @  0 % busy

  Load Information

    Load Profile................................. PASSED

    Receive Utilization.......................... 0 %

    Transmit Utilization......................... 1 %

    Channel Utilization.......................... 7 %

    Attached Clients............................. 1 clients

  Coverage Information

    Coverage Profile............................. PASSED

    Failed Clients............................... 0 clients

  Client Signal Strengths

    RSSI -100 dbm................................ 0 clients

    RSSI  -92 dbm................................ 0 clients

    RSSI  -84 dbm................................ 0 clients

    RSSI  -76 dbm................................ 0 clients

    RSSI  -68 dbm................................ 1 clients

    RSSI  -60 dbm................................ 0 clients

    RSSI  -52 dbm................................ 0 clients

  Client Signal To Noise Ratios

    SNR    0 dB.................................. 0 clients

    SNR    5 dB.................................. 0 clients

    SNR   10 dB.................................. 0 clients

    SNR   15 dB.................................. 0 clients

    SNR   20 dB.................................. 0 clients

    SNR   25 dB.................................. 1 clients

    SNR   30 dB.................................. 0 clients

    SNR   35 dB.................................. 0 clients

    SNR   40 dB.................................. 0 clients

    SNR   45 dB.................................. 0 clients

  Nearby APs

    AP cc:d5:39:d0:bf:80 slot 0..................  -62 dBm on   1 (192.168.0.7)

  Radar Information

  Channel Assignment Information

    Current Channel Average Energy............... unknown

    Previous Channel Average Energy.............. unknown

    Channel Change Count......................... 0

    Last Channel Change Time..................... Wed Jan  9 12:31:35 2013

    Recommended Best Channel..................... 11

  RF Parameter Recommendations

    Power Level.................................. 1

    RTS/CTS Threshold............................ 2347

    Fragmentation Threshold...................... 2346

    Antenna Pattern.............................. 0

  Persistent Interference Devices

  Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time

  -------------------------  -------  ------  ----------  ------------------------

  All third party trademarks are the property of their respective owners.

Number Of Slots.................................. 2

AP Name.......................................... IMEC-AP3

MAC Address...................................... ac:f2:c5:f2:78:c2

  Slot ID........................................ 1

  Radio Type..................................... RADIO_TYPE_80211a

  Sub-band Type.................................. All

  Noise Information

    Noise Profile................................ PASSED

  Interference Information

    Interference Profile......................... PASSED

    Rogue Histogram (20/40_ABOVE/40_BELOW)

    .............................................

  Load Information

    Load Profile................................. PASSED

    Receive Utilization.......................... 0 %

    Transmit Utilization......................... 0 %

    Channel Utilization.......................... 0 %

    Attached Clients............................. 0 clients

  Coverage Information

    Coverage Profile............................. PASSED

    Failed Clients............................... 0 clients

  Client Signal Strengths

    RSSI -100 dbm................................ 0 clients

    RSSI  -92 dbm................................ 0 clients

    RSSI  -84 dbm................................ 0 clients

    RSSI  -76 dbm................................ 0 clients

    RSSI  -68 dbm................................ 0 clients

    RSSI  -60 dbm................................ 0 clients

    RSSI  -52 dbm................................ 0 clients

  Client Signal To Noise Ratios

    SNR    0 dB.................................. 0 clients

    SNR    5 dB.................................. 0 clients

    SNR   10 dB.................................. 0 clients

    SNR   15 dB.................................. 0 clients

    SNR   20 dB.................................. 0 clients

    SNR   25 dB.................................. 0 clients

    SNR   30 dB.................................. 0 clients

    SNR   35 dB.................................. 0 clients

    SNR   40 dB.................................. 0 clients

    SNR   45 dB.................................. 0 clients

  Nearby APs

  Radar Information

  RF Parameter Recommendations

    Power Level.................................. 0

    RTS/CTS Threshold............................ 0

    Fragmentation Threshold...................... 0

    Antenna Pattern.............................. 0

  Persistent Interference Devices

  Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time

  -------------------------  -------  ------  ----------  ------------------------

  All third party trademarks are the property of their respective owners.

Number Of Slots.................................. 2

AP Name.......................................... IMEC-AP2

MAC Address...................................... ac:f2:c5:f3:ea:32

  Slot ID........................................ 0

  Radio Type..................................... RADIO_TYPE_80211b/g

  Sub-band Type.................................. All

  Noise Information

    Noise Profile................................ PASSED

  Interference Information

    Interference Profile......................... PASSED

  Load Information

    Load Profile................................. PASSED

    Receive Utilization.......................... 0 %

    Transmit Utilization......................... 1 %

    Channel Utilization.......................... 4 %

    Attached Clients............................. 1 clients

  Coverage Information

    Coverage Profile............................. PASSED

    Failed Clients............................... 0 clients

  Client Signal Strengths

    RSSI -100 dbm................................ 0 clients

    RSSI  -92 dbm................................ 0 clients

    RSSI  -84 dbm................................ 0 clients

    RSSI  -76 dbm................................ 0 clients

    RSSI  -68 dbm................................ 0 clients

    RSSI  -60 dbm................................ 1 clients

    RSSI  -52 dbm................................ 0 clients

  Client Signal To Noise Ratios

    SNR    0 dB.................................. 0 clients

    SNR    5 dB.................................. 0 clients

    SNR   10 dB.................................. 0 clients

    SNR   15 dB.................................. 0 clients

    SNR   20 dB.................................. 0 clients

    SNR   25 dB.................................. 0 clients

    SNR   30 dB.................................. 1 clients

    SNR   35 dB.................................. 0 clients

    SNR   40 dB.................................. 0 clients

    SNR   45 dB.................................. 0 clients

  Nearby APs

    AP cc:d5:39:d0:c8:70 slot 0..................  -57 dBm on  11 (192.168.0.7)

  Radar Information

  Channel Assignment Information

    Current Channel Average Energy............... unknown

    Previous Channel Average Energy.............. unknown

    Channel Change Count......................... 0

    Last Channel Change Time..................... Wed Jan  9 12:32:50 2013

    Recommended Best Channel..................... 1

  RF Parameter Recommendations

    Power Level.................................. 1

    RTS/CTS Threshold............................ 2347

    Fragmentation Threshold...................... 2346

    Antenna Pattern.............................. 0

  Persistent Interference Devices

  Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time

  -------------------------  -------  ------  ----------  ------------------------

  All third party trademarks are the property of their respective owners.

Number Of Slots.................................. 2

AP Name.......................................... IMEC-AP2

MAC Address...................................... ac:f2:c5:f3:ea:32

  Slot ID........................................ 1

  Radio Type..................................... RADIO_TYPE_80211a

  Sub-band Type.................................. All

  Noise Information

    Noise Profile................................ PASSED

  Interference Information

    Interference Profile......................... PASSED

    Rogue Histogram (20/40_ABOVE/40_BELOW)

    .............................................

  Load Information

    Load Profile................................. PASSED

    Receive Utilization.......................... 0 %

    Transmit Utilization......................... 0 %

    Channel Utilization.......................... 0 %

    Attached Clients............................. 0 clients

  Coverage Information

    Coverage Profile............................. PASSED

    Failed Clients............................... 0 clients

  Client Signal Strengths

    RSSI -100 dbm................................ 0 clients

    RSSI  -92 dbm................................ 0 clients

    RSSI  -84 dbm................................ 0 clients

    RSSI  -76 dbm................................ 0 clients

    RSSI  -68 dbm................................ 0 clients

    RSSI  -60 dbm................................ 0 clients

    RSSI  -52 dbm................................ 0 clients

  Client Signal To Noise Ratios

    SNR    0 dB.................................. 0 clients

    SNR    5 dB.................................. 0 clients

    SNR   10 dB.................................. 0 clients

    SNR   15 dB.................................. 0 clients

    SNR   20 dB.................................. 0 clients

    SNR   25 dB.................................. 0 clients

    SNR   30 dB.................................. 0 clients

    SNR   35 dB.................................. 0 clients

    SNR   40 dB.................................. 0 clients

    SNR   45 dB.................................. 0 clients

  Nearby APs

  Radar Information

  RF Parameter Recommendations

    Power Level.................................. 0

    RTS/CTS Threshold............................ 0

    Fragmentation Threshold...................... 0

    Antenna Pattern.............................. 0

  Persistent Interference Devices

  Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time

  -------------------------  -------  ------  ----------  ------------------------

  All third party trademarks are the property of their respective owners.

Number Of Slots.................................. 2

AP Name.......................................... IMEC-AP1

MAC Address...................................... ac:f2:c5:f3:ee:16

  Slot ID........................................ 0

  Radio Type..................................... RADIO_TYPE_80211b/g

  Sub-band Type.................................. All

  Noise Information

    Noise Profile................................ PASSED

  Interference Information

    Interference Profile......................... PASSED

  Load Information

    Load Profile................................. PASSED

    Receive Utilization.......................... 0 %

    Transmit Utilization......................... 1 %

    Channel Utilization.......................... 9 %

    Attached Clients............................. 0 clients

  Coverage Information

    Coverage Profile............................. PASSED

    Failed Clients............................... 0 clients

  Client Signal Strengths

    RSSI -100 dbm................................ 0 clients

    RSSI  -92 dbm................................ 0 clients

    RSSI  -84 dbm................................ 0 clients

    RSSI  -76 dbm................................ 0 clients

    RSSI  -68 dbm................................ 0 clients

    RSSI  -60 dbm................................ 0 clients

    RSSI  -52 dbm................................ 0 clients

  Client Signal To Noise Ratios

    SNR    0 dB.................................. 0 clients

    SNR    5 dB.................................. 0 clients

    SNR   10 dB.................................. 0 clients

    SNR   15 dB.................................. 0 clients

    SNR   20 dB.................................. 0 clients

    SNR   25 dB.................................. 0 clients

    SNR   30 dB.................................. 0 clients

    SNR   35 dB.................................. 0 clients

    SNR   40 dB.................................. 0 clients

    SNR   45 dB.................................. 0 clients

  Nearby APs

  Radar Information

  Channel Assignment Information

    Current Channel Average Energy............... unknown

    Previous Channel Average Energy.............. unknown

    Channel Change Count......................... 0

    Last Channel Change Time..................... Wed Jan  9 12:33:48 2013

    Recommended Best Channel..................... 6

  RF Parameter Recommendations

    Power Level.................................. 1

    RTS/CTS Threshold............................ 2347

    Fragmentation Threshold...................... 2346

    Antenna Pattern.............................. 0

  Persistent Interference Devices

  Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time

  -------------------------  -------  ------  ----------  ------------------------

  All third party trademarks are the property of their respective owners.

Number Of Slots.................................. 2

AP Name.......................................... IMEC-AP1

MAC Address...................................... ac:f2:c5:f3:ee:16

  Slot ID........................................ 1

  Radio Type..................................... RADIO_TYPE_80211a

  Sub-band Type.................................. All

  Noise Information

    Noise Profile................................ PASSED

  Interference Information

    Interference Profile......................... PASSED

    Rogue Histogram (20/40_ABOVE/40_BELOW)

    .............................................

  Load Information

    Load Profile................................. PASSED

    Receive Utilization.......................... 0 %

    Transmit Utilization......................... 0 %

    Channel Utilization.......................... 0 %

    Attached Clients............................. 0 clients

  Coverage Information

    Coverage Profile............................. PASSED

    Failed Clients............................... 0 clients

  Client Signal Strengths

    RSSI -100 dbm................................ 0 clients

    RSSI  -92 dbm................................ 0 clients

    RSSI  -84 dbm................................ 0 clients

    RSSI  -76 dbm................................ 0 clients

    RSSI  -68 dbm................................ 0 clients

    RSSI  -60 dbm................................ 0 clients

    RSSI  -52 dbm................................ 0 clients

  Client Signal To Noise Ratios

    SNR    0 dB.................................. 0 clients

    SNR    5 dB.................................. 0 clients

    SNR   10 dB.................................. 0 clients

    SNR   15 dB.................................. 0 clients

    SNR   20 dB.................................. 0 clients

    SNR   25 dB.................................. 0 clients

    SNR   30 dB.................................. 0 clients

    SNR   35 dB.................................. 0 clients

    SNR   40 dB.................................. 0 clients

    SNR   45 dB.................................. 0 clients

  Nearby APs

  Radar Information

  RF Parameter Recommendations

    Power Level.................................. 0

    RTS/CTS Threshold............................ 0

    Fragmentation Threshold...................... 0

    Antenna Pattern.............................. 0

  Persistent Interference Devices

  Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time

  -------------------------  -------  ------  ----------  ------------------------

  All third party trademarks are the property of their respective owners.

802.11a Configuration

802.11a Network.................................. Enabled

11nSupport....................................... Enabled

      802.11a Low Band........................... Enabled

      802.11a Mid Band........................... Enabled

      802.11a High Band.......................... Enabled

802.11a Operational Rates

    802.11a 6M Rate.............................. Mandatory

    802.11a 9M Rate.............................. Supported

    802.11a 12M Rate............................. Mandatory

    802.11a 18M Rate............................. Supported

    802.11a 24M Rate............................. Mandatory

    802.11a 36M Rate............................. Supported

    802.11a 48M Rate............................. Supported

    802.11a 54M Rate............................. Supported

802.11n MCS Settings:

    MCS 0........................................ Supported

    MCS 1........................................ Supported

    MCS 2........................................ Supported

    MCS 3........................................ Supported

    MCS 4........................................ Supported

    MCS 5........................................ Supported

    MCS 6........................................ Supported

    MCS 7........................................ Supported

    MCS 8........................................ Supported

    MCS 9........................................ Supported

    MCS 10....................................... Supported

    MCS 11....................................... Supported

    MCS 12....................................... Supported

    MCS 13....................................... Supported

    MCS 14....................................... Supported

    MCS 15....................................... Supported

802.11n Status:

    A-MPDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Disabled

        Priority 2............................... Disabled

        Priority 3............................... Disabled

        Priority 4............................... Enabled

        Priority 5............................... Enabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

    A-MSDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Enabled

        Priority 2............................... Enabled

        Priority 3............................... Enabled

        Priority 4............................... Enabled

        Priority 5............................... Enabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

    Rifs Rx ..................................... Enabled

    Guard Interval .............................. Any

Beacon Interval.................................. 100

CF Pollable mandatory............................ Disabled

CF Poll Request mandatory........................ Disabled

CFP Period....................................... 4

CFP Maximum Duration............................. 60

Default Channel.................................. 36

Default Tx Power Level........................... 0

DTPC  Status..................................... Enabled

Fragmentation Threshold.......................... 2346

TI Threshold..................................... -50

Legacy Tx Beamforming setting.................... Disabled

Traffic Stream Metrics Status.................... Disabled

Expedited BW Request Status...................... Disabled

World Mode....................................... Enabled

EDCA profile type................................ default-wmm

Voice MAC optimization status.................... Disabled

Call Admission Control (CAC) configuration

Voice AC:

   Voice AC - Admission control (ACM)............ Disabled

   Voice Stream-Size............................. 84000

   Voice Max-Streams............................. 2

   Voice max RF bandwidth........................ 75

   Voice reserved roaming bandwidth.............. 6

   Voice CAC Method ............................. Load-Based

   Voice tspec inactivity timeout................ Disabled

CAC SIP-Voice configuration

   SIP based CAC ................................ Disabled

   SIP Codec Type ............................... CODEC_TYPE_G711

   SIP call bandwidth ........................... 64

   SIP call bandwith sample-size ................ 20

Video AC:

   Video AC - Admission control (ACM)............ Disabled

   Video max RF bandwidth........................ Infinite

   Video reserved roaming bandwidth.............. 0

   Best-effort AC - Admission control (ACM)...... Disabled

   Background AC - Admission control (ACM)....... Disabled

802.11a Advanced Configuration

AP Name                          MAC Address        Admin State  Operation State Channel    TxPower

-------------------------------- ------------------ ------------ --------------- ---------- --------

IMEC-AP3                         cc:d5:39:d0:c8:70  ENABLED      DOWN            165*         1(*)

IMEC-AP2                         cc:d5:39:d0:bf:80  ENABLED      DOWN            165*         1(*)

IMEC-AP1                         cc:d5:39:d1:0c:20  ENABLED      DOWN            165*         1(*)

802.11a Airewave Director Configuration

RF Event and Performance Logging

  Channel Update Logging......................... Off

  Coverage Profile Logging....................... Off

  Foreign Profile Logging........................ Off

  Load Profile Logging........................... Off

  Noise Profile Logging.......................... Off

  Performance Profile Logging.................... Off

  TxPower Update Logging......................... Off

Default 802.11a AP performance profiles

  802.11a Global Interference threshold.......... 10 %

  802.11a Global noise threshold................. -70 dBm

  802.11a Global RF utilization threshold........ 80 %

  802.11a Global throughput threshold............ 1000000 bps

  802.11a Global clients threshold............... 12 clients

Default 802.11a AP monitoring

  802.11a Monitor Mode........................... enable

  802.11a Monitor Mode for Mesh AP Backhaul...... disable

  802.11a Monitor Channels....................... Country channels

  802.11a RRM Neighbor Discover Type............. Transparent

  802.11a AP Coverage Interval................... 180 seconds

  802.11a AP Load Interval....................... 60 seconds

  802.11a AP Noise Interval...................... 180 seconds

  802.11a AP Signal Strength Interval............ 60 seconds

Automatic Transmit Power Assignment

  Transmit Power Assignment Mode................. AUTO

  Transmit Power Update Interval................. 600 seconds

  Transmit Power Threshold....................... -70 dBm

  Transmit Power Neighbor Count.................. 3 APs

  Min Transmit Power............................. -10 dBm

  Max Transmit Power............................. 30 dBm

  Transmit Power Update Contribution............. SNI..

  Transmit Power Assignment Leader............... IMEC-WLAN (192.168.0.7)

  Last Run....................................... 533 seconds ago

Coverage Hole Detection

  802.11a Coverage Hole Detection Mode........... Enabled

  802.11a Coverage Voice Packet Count............ 100 packets

  802.11a Coverage Voice Packet Percentage....... 50%

  802.11a Coverage Voice RSSI Threshold.......... -80 dBm

  802.11a Coverage Data Packet Count............. 50 packets

  802.11a Coverage Data Packet Percentage........ 50%

  802.11a Coverage Data RSSI Threshold........... -80 dBm

  802.11a Global coverage exception level........ 25 %

  802.11a Global client minimum exception lev.... 3 clients

Automatic Channel Assignment

  Channel Assignment Mode........................ AUTO

  Channel Update Interval........................ 600 seconds [startup]

  Anchor time (Hour of the day).................. 0

  Channel Update Contribution.................... SNI..

  CleanAir Event-driven RRM option............... Disabled

  CleanAir Event-driven RRM sensitivity.......... Medium

  Channel Assignment Leader...................... IMEC-WLAN (192.168.0.7)

  Last Run....................................... 533 seconds ago

  DCA Sensitivity Level.......................... STARTUP (5 dB)

  DCA 802.11n Channel Width...................... 20 MHz

  DCA Minimum Energy Limit....................... -95 dBm

  Channel Energy Levels

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  Channel Dwell Times

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  802.11a 5 GHz Auto-RF Channel List

    Allowed Channel List......................... 36,40,44,48,52,56,60,64,149,

                                                  153,157,161

    Unused Channel List.......................... 100,104,108,112,116,132,136,

                                                  140,165

  802.11a 4.9 GHz Auto-RF Channel List

    Allowed Channel List.........................

    Unused Channel List.......................... 1,2,3,4,5,6,7,8,9,10,11,12,

                                                  13,14,15,16,17,18,19,20,21,

                                                  22,23,24,25,26

  DCA Outdoor AP option.......................... Disabled

Radio RF Grouping

  802.11a Group Mode............................. AUTO

  802.11a Group Update Interval.................. 600 seconds

  802.11a Group Leader........................... IMEC-WLAN (192.168.0.7)

    802.11a Group Member......................... IMEC-WLAN (192.168.0.7)

  802.11a Last Run............................... 533 seconds ago

802.11a CleanAir Configuration

Clean Air Solution............................... Disabled

Air Quality Settings:

    Air Quality Reporting........................ Enabled

    Air Quality Reporting Period (min)........... 15

    Air Quality Alarms........................... Enabled

    Air Quality Alarm Threshold.................. 35

Interference Device Settings:

    Interference Device Reporting................ Enabled

    Interference Device Types:

        TDD Transmitter.......................... Enabled

        Jammer................................... Enabled

        Continuous Transmitter................... Enabled

        DECT-like Phone.......................... Enabled

        Video Camera............................. Enabled

        WiFi Inverted............................ Enabled

        WiFi Invalid Channel..................... Enabled

        SuperAG.................................. Enabled

        Canopy................................... Enabled

        WiMax Mobile............................. Enabled

        WiMax Fixed.............................. Enabled

    Interference Device Alarms................... Enabled

    Interference Device Types Triggering Alarms:

        TDD Transmitter.......................... Disabled

        Jammer................................... Enabled

        Continuous Transmitter................... Disabled

        DECT-like Phone.......................... Disabled

        Video Camera............................. Disabled

        WiFi Inverted............................ Enabled

        WiFi Invalid Channel..................... Enabled

        SuperAG.................................. Disabled

        Canopy................................... Disabled

        WiMax Mobile............................. Disabled

        WiMax Fixed.............................. Disabled

Additional Clean Air Settings:

    CleanAir Event-driven RRM State.............. Disabled

    CleanAir Driven RRM Sensitivity.............. Medium

    CleanAir Persistent Devices state............ Disabled

802.11a CleanAir AirQuality Summary

AQ = Air Quality

DFS = Dynamic Frequency Selection

AP Name            Channel Avg AQ Min AQ Interferers DFS

------------------ ------- ------ ------ ----------- ---

802.11b Configuration

802.11b Network.................................. Enabled

11gSupport....................................... Enabled

11nSupport....................................... Enabled

802.11b/g Operational Rates

    802.11b/g 1M Rate............................ Mandatory

    802.11b/g 2M Rate............................ Mandatory

    802.11b/g 5.5M Rate.......................... Mandatory

    802.11b/g 11M Rate........................... Mandatory

    802.11g 6M Rate.............................. Supported

    802.11g 9M Rate.............................. Supported

    802.11g 12M Rate............................. Supported

    802.11g 18M Rate............................. Supported

    802.11g 24M Rate............................. Supported

    802.11g 36M Rate............................. Supported

    802.11g 48M Rate............................. Supported

    802.11g 54M Rate............................. Supported

802.11n MCS Settings:

    MCS 0........................................ Supported

    MCS 1........................................ Supported

    MCS 2........................................ Supported

    MCS 3........................................ Supported

    MCS 4........................................ Supported

    MCS 5........................................ Supported

    MCS 6........................................ Supported

    MCS 7........................................ Supported

    MCS 8........................................ Supported

    MCS 9........................................ Supported

    MCS 10....................................... Supported

    MCS 11....................................... Supported

    MCS 12....................................... Supported

    MCS 13....................................... Supported

    MCS 14....................................... Supported

    MCS 15....................................... Supported

802.11n Status:

    A-MPDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Disabled

        Priority 2............................... Disabled

        Priority 3............................... Disabled

        Priority 4............................... Enabled

        Priority 5............................... Enabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

    A-MSDU Tx:

        Priority 0............................... Enabled

        Priority 1............................... Enabled

        Priority 2............................... Enabled

        Priority 3............................... Enabled

        Priority 4............................... Enabled

        Priority 5............................... Enabled

        Priority 6............................... Disabled

        Priority 7............................... Disabled

    Rifs Rx ..................................... Enabled

    Guard Interval .............................. Any

Beacon Interval.................................. 100

CF Pollable mode................................. Disabled

CF Poll Request mandatory........................ Disabled

CFP Period....................................... 4

CFP Maximum Duration............................. 60

Default Channel.................................. 1

Default Tx Power Level........................... 0

DTPC  Status..................................... Enabled

Call Admission Limit  ........................... 105

G711 CU Quantum ................................. 15

ED Threshold..................................... -50

Fragmentation Threshold.......................... 2346

PBCC mandatory................................... Disabled

RTS Threshold.................................... 2347

Short Preamble mandatory......................... Enabled

Short Retry Limit................................ 7

Legacy Tx Beamforming setting.................... Disabled

Traffic Stream Metrics Status.................... Disabled

Expedited BW Request Status...................... Disabled

World Mode....................................... Enabled

Faster Carrier Tracking Loop..................... Disabled

EDCA profile type................................ default-wmm

Voice MAC optimization status.................... Disabled

Call Admission Control (CAC) configuration

   Voice AC - Admission control (ACM)............ Disabled

   Voice Stream-Size............................. 84000

   Voice Max-Streams............................. 2

   Voice max RF bandwidth........................ 75

   Voice reserved roaming bandwidth.............. 6

   Voice CAC Method.............................. Load-Based

   Voice tspec inactivity timeout................ Disabled

CAC SIP-Voice configuration

   SIP based CAC ................................ Disabled

   SIP Codec Type ............................... CODEC_TYPE_G711

   SIP call bandwidth: .......................... 64

   SIP call bandwidth sample-size ............... 20

   Video AC - Admission control (ACM)............ Disabled

   Video max RF bandwidth........................ Infinite

   Video reserved roaming bandwidth.............. 0

   Best-effort AC - Admission control (ACM)...... Disabled

   Background AC - Admission control (ACM)....... Disabled

802.11b Advanced Configuration

AP Name                          MAC Address        Admin State  Operation State Channel    TxPower

-------------------------------- ------------------ ------------ --------------- ---------- --------

IMEC-AP3                         cc:d5:39:d0:c8:70  ENABLED      UP              11*          1(*)

IMEC-AP2                         cc:d5:39:d0:bf:80  ENABLED      UP              1*           1(*)

IMEC-AP1                         cc:d5:39:d1:0c:20  ENABLED      UP              6*           1(*)

802.11b Airewave Director Configuration

RF Event and Performance Logging

  Channel Update Logging......................... Off

  Coverage Profile Logging....................... Off

  Foreign Profile Logging........................ Off

  Load Profile Logging........................... Off

  Noise Profile Logging.......................... Off

  Performance Profile Logging.................... Off

  Transmit Power Update Logging.................. Off

Default 802.11b AP performance profiles

  802.11b Global Interference threshold.......... 10 %

  802.11b Global noise threshold................. -70 dBm

  802.11b Global RF utilization threshold........ 80 %

  802.11b Global throughput threshold............ 1000000 bps

  802.11b Global clients threshold............... 12 clients

Default 802.11b AP monitoring

  802.11b Monitor Mode........................... enable

  802.11b Monitor Channels....................... Country channels

  802.11b RRM Neighbor Discovery Type............ Transparent

  802.11b AP Coverage Interval................... 180 seconds

  802.11b AP Load Interval....................... 60 seconds

  802.11b AP Noise Interval...................... 180 seconds

  802.11b AP Signal Strength Interval............ 60 seconds

Automatic Transmit Power Assignment

  Transmit Power Assignment Mode................. AUTO

  Transmit Power Update Interval................. 600 seconds

  Transmit Power Threshold....................... -70 dBm

  Transmit Power Neighbor Count.................. 3 APs

  Min Transmit Power............................. -10 dBm

  Max Transmit Power............................. 30 dBm

  Transmit Power Update Contribution............. SNI..

  Transmit Power Assignment Leader............... IMEC-WLAN (192.168.0.7)

  Last Run....................................... 536 seconds ago

Coverage Hole Detection

  802.11b Coverage Hole Detection Mode........... Enabled

  802.11b Coverage Voice Packet Count............ 100 packets

  802.11b Coverage Voice Packet Percentage....... 50%

  802.11b Coverage Voice RSSI Threshold.......... -80 dBm

  802.11b Coverage Data Packet Count............. 50 packets

  802.11b Coverage Data Packet Percentage........ 50%

  802.11b Coverage Data RSSI Threshold........... -80 dBm

  802.11b Global coverage exception level........ 25 %

  802.11b Global client minimum exception lev.... 3 clients

Automatic Channel Assignment

  Channel Assignment Mode........................ AUTO

  Channel Update Interval........................ 600 seconds [startup]

  Anchor time (Hour of the day).................. 0

  Channel Update Contribution.................... SNI..

  CleanAir Event-driven RRM option............... Disabled

  CleanAir Event-driven RRM sensitivity.......... Medium

  Channel Assignment Leader...................... IMEC-WLAN (192.168.0.7)

  Last Run....................................... 536 seconds ago

  DCA Sensitivity Level: ...................... STARTUP (5 dB)

  DCA Minimum Energy Limit....................... -95 dBm

  Channel Energy Levels

    Minimum...................................... unknown

    Average...................................... unknown

    Maximum...................................... unknown

  Channel Dwell Times

    Minimum...................................... 0 days, 00 h 01 m 14 s

    Average...................................... 0 days, 00 h 02 m 17 s

    Maximum...................................... 0 days, 00 h 03 m 27 s

  802.11b Auto-RF Allowed Channel List........... 1,6,11

  Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10

Radio RF Grouping

  802.11b Group Mode............................. AUTO

  802.11b Group Update Interval.................. 600 seconds

  802.11b Group Leader........................... IMEC-WLAN (192.168.0.7)

    802.11b Group Member......................... IMEC-WLAN (192.168.0.7)

  802.11b Last Run............................... 536 seconds ago

802.11a CleanAir Configuration

Clean Air Solution............................... Disabled

Air Quality Settings:

    Air Quality Reporting........................ Enabled

    Air Quality Reporting Period (min)........... 15

    Air Quality Alarms........................... Enabled

    Air Quality Alarm Threshold.................. 35

Interference Device Settings:

    Interference Device Reporting................ Enabled

    Interference Device Types:

        Bluetooth Link........................... Enabled

        Microwave Oven........................... Enabled

        802.11 FH................................ Enabled

        Bluetooth Discovery...................... Enabled

        TDD Transmitter.......................... Enabled

        Jammer................................... Enabled

        Continuous Transmitter................... Enabled

        DECT-like Phone.......................... Enabled

        Video Camera............................. Enabled

        802.15.4................................. Enabled

        WiFi Inverted............................ Enabled

        WiFi Invalid Channel..................... Enabled

        SuperAG.................................. Enabled

        Canopy................................... Enabled

        Microsoft Device......................... Enabled

        WiMax Mobile............................. Enabled

        WiMax Fixed.............................. Enabled

    Interference Device Alarms................... Enabled

    Interference Device Types Triggering Alarms:

        Bluetooth Link........................... Disabled

        Microwave Oven........................... Disabled

        802.11 FH................................ Disabled

        Bluetooth Discovery...................... Disabled

        TDD Transmitter.......................... Disabled

        Jammer................................... Enabled

        Continuous Transmitter................... Disabled

        DECT-like Phone.......................... Disabled

        Video Camera............................. Disabled

        802.15.4................................. Disabled

        WiFi Inverted............................ Enabled

        WiFi Invalid Channel..................... Enabled

        SuperAG.................................. Disabled

        Canopy................................... Disabled

        Microsoft Device......................... Disabled

        WiMax Mobile............................. Disabled

        WiMax Fixed.............................. Disabled

Additional Clean Air Settings:

    CleanAir Event-driven RRM State.............. Disabled

    CleanAir Driven RRM Sensitivity.............. Medium

    CleanAir Persistent Devices state............ Disabled

802.11a CleanAir AirQuality Summary

AQ = Air Quality

DFS = Dynamic Frequency Selection

AP Name            Channel Avg AQ Min AQ Interferers DFS

------------------ ------- ------ ------ ----------- ---

Mobility Configuration

Symmetric Mobility Tunneling (current) .......... Enabled

Symmetric Mobility Tunneling (after reboot) ..... Enabled

Mobility Protocol Port........................... 16666

Default Mobility Domain.......................... IMEC

Multicast Mode .................................. Disabled

Mobility Domain ID for 802.11r................... 0x9344

Mobility Keepalive Interval...................... 10

Mobility Keepalive Count......................... 3

Mobility Group Members Configured................ 1

Mobility Control Message DSCP Value.............. 0

Controllers configured in the Mobility Group

MAC Address        IP Address       Group Name                        Multicast IP     Status

f4:7f:35:b7:70:20  192.168.0.7      IMEC                              0.0.0.0          Up

Mobility Foreign Map Configuration

WLAN ID     Foreign Mac Address     Interface

-------     -------------------     ---------

Advanced Configuration

Probe request filtering..........................  Enabled

Probes fwd to controller per client per radio....  2

Probe request rate-limiting interval.............  500 msec

Aggregate Probe request interval.................  500 msec

EAP-Identity-Request Timeout (seconds)........... 30

EAP-Identity-Request Max Retries................. 2

EAP Key-Index for Dynamic WEP.................... 0

EAP Max-Login Ignore Identity Response........... enable

EAP-Request Timeout (seconds).................... 30

EAP-Request Max Retries.......................... 2

EAPOL-Key Timeout (milliseconds)................. 1000

EAPOL-Key Max Retries............................ 2

EAP-Broadcast Key Interval....................... 3600

Fastpath Packet Capture.......................... disable

Fastpath Fast Cache Control...................... enable

Fastpath Fast Testmode........................... 0x0

dot11-padding.................................... Disabled

Location Configuration

RFID Tag data Collection......................... Enabled

RFID  timeout.................................... 1200 seconds

RFID mobility.................................... Oui:00:14:7e : Vendor:pango  State:Disabled

Interface Configuration

Interface Name................................... management

MAC Address...................................... f4:7f:35:b7:70:20

IP Address....................................... 192.168.0.7

IP Netmask....................................... 255.255.255.0

IP Gateway....................................... 192.168.0.1

External NAT IP State............................ Disabled

External NAT IP Address.......................... 0.0.0.0

VLAN............................................. untagged 

Quarantine-vlan.................................. 0

Active Physical Port............................. 1        

Primary Physical Port............................ 1        

Backup Physical Port............................. Unconfigured

Primary DHCP Server.............................. 192.168.0.1

Secondary DHCP Server............................ Unconfigured

DHCP Option 82................................... Disabled

ACL.............................................. Unconfigured

AP Manager....................................... Yes

Guest Interface.................................. No

L2 Multicast..................................... Disabled

Interface Name................................... virtual

MAC Address...................................... f4:7f:35:b7:70:20

IP Address....................................... 1.1.1.1

DHCP Option 82................................... Disabled

Virtual DNS Host Name............................ Disabled

AP Manager....................................... No

Guest Interface.................................. No

Interface Group Configuration

WLAN Configuration

WLAN Identifier.................................. 1

Profile Name..................................... IMEC-INDIA

Network Name (SSID).............................. IMEC-INDIA

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Enabled

AAA Policy Override.............................. Disabled

Network Admission Control

  Radius-NAC State............................... Disabled

  SNMP-NAC State................................. Disabled

  Quarantine VLAN................................ 0

Maximum number of Associated Clients............. 0

Number of Active Clients......................... 2

Exclusionlist Timeout............................ 60 seconds

Session Timeout.................................. 1800 seconds

CHD per WLAN..................................... Enabled

Webauth DHCP exclusion........................... Disabled

Interface........................................ management

Multicast Interface.............................. Not Configured

WLAN ACL......................................... unconfigured

DHCP Server...................................... Default

DHCP Address Assignment Required................. Disabled

Static IP client tunneling....................... Disabled

Quality of Service............................... Silver (best effort)

Scan Defer Priority.............................. 4,5,6

Scan Defer Time.................................. 100 milliseconds

WMM.............................................. Allowed

WMM UAPSD Compliant Client Support............... Disabled

Media Stream Multicast-direct.................... Disabled

CCX - AironetIe Support.......................... Enabled

CCX - Gratuitous ProbeResponse (GPR)............. Disabled

CCX - Diagnostics Channel Capability............. Disabled

Dot11-Phone Mode (7920).......................... Disabled

Wired Protocol................................... None

IPv6 Support..................................... Disabled

Passive Client Feature........................... Disabled

Peer-to-Peer Blocking Action..................... Disabled

Radio Policy..................................... All

DTIM period for 802.11a radio.................... 1

DTIM period for 802.11b radio.................... 1

Radius Servers

   Authentication................................ Global Servers

   Accounting.................................... Global Servers

   Dynamic Interface............................. Disabled

Local EAP Authentication......................... Disabled

Security

   802.11 Authentication:........................ Open System

   Static WEP Keys............................... Enabled

Key Index:...................................... 2

Encryption:..................................... 104-bit WEP

   802.1X........................................ Disabled

   Wi-Fi Protected Access (WPA/WPA2)............. Disabled

   CKIP ......................................... Disabled

   Web Based Authentication...................... Disabled

   Web-Passthrough............................... Disabled

   Conditional Web Redirect...................... Disabled

   Splash-Page Web Redirect...................... Disabled

   Auto Anchor................................... Disabled

   H-REAP Local Switching........................ Disabled

   H-REAP Local Authentication................... Disabled

   H-REAP Learn IP Address....................... Enabled

   Client MFP.................................... Optional but inactive (WPA2 not configured)

   Tkip MIC Countermeasure Hold-down Timer....... 60

Call Snooping.................................... Disabled

Roamed Call Re-Anchor Policy..................... Disabled

SIP CAC Fail Send-486-Busy Policy................ Enabled

SIP CAC Fail Send Dis-Association Policy......... Disabled

Band Select...................................... Disabled

Load Balancing................................... Disabled

Mobility Anchor List

WLAN ID     IP Address            Status

-------     ---------------       ------

ACL Configuration

CPU ACL Configuration

CPU Acl Name................................ NOT CONFIGURED

Wireless Traffic............................ Disabled

Wired Traffic............................... Disabled

RADIUS Configuration

Vendor Id Backward Compatibility................. Disabled

Call Station Id Case............................. lower

Call Station Id Type............................. IP Address

Aggressive Failover.............................. Enabled

Keywrap.......................................... Disabled

Fallback Test:

    Test Mode.................................... Off

    Probe User Name.............................. cisco-probe

    Interval (in seconds)........................ 300

MAC Delimiter for Authentication Messages........ hyphen

MAC Delimiter for Accounting Messages............ hyphen

Authentication Servers

Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/Phase1/Group/Lifetime/Auth/Encr

---  ----  ----------------  ------  --------  ----  -------  ------------------------------------------------

Accounting Servers

Idx  Type  Server Address    Port    State     Tout  RFC3576  IPSec - AuthMode/Phase1/Group/Lifetime/Auth/Encr

---  ----  ----------------  ------  --------  ----  -------  ------------------------------------------------

TACACS Configuration

Authentication Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

Authorization Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

Accounting Servers

Idx  Server Address    Port    State     Tout

---  ----------------  ------  --------  ----

LDAP Configuration

Local EAP Configuration

User credentials database search order:

    Primary ..................................... Local DB

Timer:

    Active timeout .............................. 300

Configured EAP profiles:

EAP Method configuration:

    EAP-FAST:

      Server key ................................

      TTL for the PAC ........................... 10

      Anonymous provision allowed ............... Yes

      Authority ID .............................. 436973636f0000000000000000000000

      Authority Information ..................... Cisco A-ID

HREAP Group Summary

HREAP Group Summary: Count: 0

Group Name                # Aps

HREAP Group Detail

Route  Info

Number of Routes................................. 0

Destination Network          Netmask               Gateway

-------------------    -------------------   -------------------

Qos Queue Length Info

Platinum queue length............................ 100

Gold queue length................................  75

Silver queue length..............................  50

Bronze queue length..............................  25

Mac Filter Info

Authorization List

Authorize MIC APs against AAA ................... disabled

Authorize LSC APs against Auth-List ............. disabled

APs Allowed to Join

  AP with Manufacturing Installed Certificate.... yes

  AP with Self-Signed Certificate................ no

  AP with Locally Significant Certificate........ no

Load Balancing Info

Aggressive Load Balancing........................ per WLAN enabling

Aggressive Load Balancing Window................. 5 clients

Aggressive Load Balancing Denial Count........... 3

Statistics

Total Denied Count............................... 0 clients

Total Denial Sent................................ 0 messages

Exceeded Denial Max Limit Count.................. 0 times

None 5G Candidate Count.......................... 0 times

None 2.4G Candidate Count........................ 0 times

DHCP Info

No leases allocated.

DHCP Opt-82 RID Format:

DHCP Proxy Behaviour:enabled

DHCP Server IP Address:.......................... 192.168.0.1

  DHCP DISCOVER Count:........................... 24

  DHCP REQUEST Count:............................ 0

  DHCP INFORM Count:............................. 0

  DHCP DECLINE Count:............................ 0

  DHCP RELEASE Count:............................ 0

  DHCP REPLY Count:.............................. 0

  DHCP OFFER Count:.............................. 23

  DHCP ACK Count:................................ 0

  DHCP NAK Count:................................ 0

  Tx Fails:...................................... 0

  Last Rx Time:.................................. 39 seconds ago

  Last Tx Time:.................................. 39 seconds ago

Exclusion List ConfigurationUnable to retrieve exclusion-list entry

CDP Configuration

cdp version v2

Country Channels Configuration

Configured Country............................. US  - United States

      KEY: * = Channel is legal in this country and may be configured manually.

           A = Channel is the Auto-RF default in this country.

           . = Channel is not legal in this country.

           C = Channel has been configured for use by Auto-RF.

           x = Channel is available to be configured for use by Auto-RF.

         (-,-) = (indoor, outdoor) regulatory doamin allowed by this country.

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

    802.11bg     :                           

    Channels     :                   1 1 1 1 1

                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-

US (-A   ,-AB  ): A * * * * A * * * * A . . .

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

    802.11a      :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

    Channels     : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6

                 : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

US (-A   ,-AB  ): . A . A . A . A A A A A * * * * * . . . * * * A A A A *

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

4.9GHz 802.11a  :                                                   

    Channels     :                   1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2

                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

US (-A   ,-AB  ): * * * * * * * * * * * * * * * * * * * A * * * * * A

-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-

WPS Configuration Summary

Auto-Immune

  Auto-Immune.................................... Disabled

Client Exclusion Policy

  Excessive 802.11-association failures.......... Enabled

  Excessive 802.11-authentication failures....... Enabled

  Excessive 802.1x-authentication................ Enabled

  IP-theft....................................... Enabled

  Excessive Web authentication failure........... Enabled

Signature Policy

  Signature Processing........................... Enabled

Custom Web Configuration

Radius Authentication Method..................... PAP

Cisco Logo....................................... Enabled

CustomLogo....................................... None

Custom Title..................................... None

Custom Message................................... None

Custom Redirect URL.............................. None

Web Authentication Type.......................... Internal Default

External Web Authentication URL.................. None

Configuration Per Profile:

Core dump Configuration

Core Dump is disabled

Rogue AP Configuration

Rogue on wire Auto-Contain....................... Disabled

Rogue using our SSID Auto-Contain................ Disabled

Valid client on rogue AP Auto-Contain............ Disabled

Rogue AP timeout................................. 1200

Monitor Mode Report Interval..................... 10

MAC Address        Classification     # APs # Clients Last Heard            

-----------------  ------------------ ----- --------- -----------------------

00:27:22:4e:0a:ac  Pending            1     0         Wed Jan  9 12:34:40 2013

00:e0:4c:00:57:48  Pending            1     0         Wed Jan  9 12:34:40 2013

04:4f:aa:33:08:38  Pending            1     0         Wed Jan  9 12:34:40 2013

Adhoc Rogue Configuration

Detect and report Ad-Hoc Networks................ Enabled

Auto-Contain Ad-Hoc Networks..................... Disabled

Client MAC Address  Adhoc BSSID         State              # APs   Last Heard            

------------------  ------------------  -----------------  ------  -----------------------

Rogue Client Configuration

Validate rogue clients against AAA............... Disabled

MAC Address        State              # APs Last Heard            

-----------------  ------------------ ----- -----------------------

Ignore List Configuration

MAC Address      

-----------------

Rogue Rule Configuration

Priority Rule Name               State    Type          Match Hit Count

-------- ----------------------- -------- ------------- ----- ---------

Media-Stream Configuration

Multicast-direct State........................... disable

Allowed WLANs....................................

Stream Name   Start IP       End IP         Operation Status

------------- -------------- -------------- ----------------

URL..............................................

E-mail...........................................

Phone............................................

Note.............................................

State............................................ disable

2.4G Band Media-Stream Configuration

Multicast-direct................................. Enabled

Best Effort...................................... Disabled

Video Re-Direct.................................. Enabled

Max Allowed Streams Per Radio.................... Auto

Max Allowed Streams Per Client................... Auto

Max Video Bandwidth.............................. 0

Max Voice Bandwidth.............................. 75

Max Media Bandwidth.............................. 85

Min PHY Rate..................................... 6000

Max Retry Percentage............................. 80

5G Band Media-Stream Configuration

Multicast-direct................................. Enabled

Best Effort...................................... Disabled

Video Re-Direct.................................. Enabled

Max Allowed Streams Per Radio.................... Auto

Max Allowed Streams Per Client................... Auto

Max Video Bandwidth.............................. 0

Max Voice Bandwidth.............................. 75

Max Media Bandwidth.............................. 85

Min PHY Rate..................................... 6000

Max Retry Percentage............................. 80

Number of Clients................................ 0

Client Mac         Stream Name  Stream Type  Radio WLAN  QoS    Status

-----------------  -----------  -----------  ----  ----  ------ -------

(Cisco Controller) >?

kcnajaf@25070 Tue, 01/08/2013 - 23:19

Hi,

Could you try modyting yiu configuration as below

WLAN Identifier.................................. 1

Profile Name..................................... IMEC-INDIA

Network Name (SSID).............................. IMEC-INDIA

Status........................................... Enabled

MAC Filtering.................................... Disabled

Broadcast SSID................................... Enabled

DHCP Server...................................... Default (Change to 192.168.0.1)

DHCP Address Assignment Required................. Disabled (Change to Enable)

Regards

Najaf

Please rate when applicable or helpful !!!

shibivdev Wed, 01/09/2013 - 02:47

Hav you checked the Configuration of the Virtual Interface associated with SSID, because DHCP Server IP should be added in the interface, you can confirm that through GUI of the Controller

amankhang Wed, 01/09/2013 - 05:51

Hi,

-Najaf

Not able to find the command or in the GUI to change the following parameters.. any idea on that

DHCP Server...................................... Default (Change to 192.168.0.1)

DHCP Address Assignment Required................. Disabled (Change to Enable)

-shibivdev

i did'nt got similar to that in the interfaces but i have:

and

kcnajaf@25070 Wed, 01/09/2013 - 06:12

Hi,

This will under WLANs-->Click on WLAN ID (Of the SSID which you want this change)-->Advance Tab --> DHCP

Hope this is the path as i have not worked on 2504 :-)

Regards

Najaf

amankhang Wed, 01/09/2013 - 06:32

made those changes:

before changes:

after changes:

I have a remote of it and gonna check it tomarrow morning

But tell me "every thing was working fine from past two months" the client used to get ip address and accesability.

how can it stop working with out any changes..

Scott Fella Wed, 01/09/2013 - 08:18

Well maybe the configuration was never saved and then it was rebooted without saving the changes?

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

Stephen Rodriguez Wed, 01/09/2013 - 08:22

So, the config on the WLC looks fine.  You do not need to do the DHCP overide under the WLAN, just have the server configured in the interface.

But out of curiosity, can you look at the switch to see if someone has enabled teh dot1q native vlan tag command?

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

amankhang Wed, 01/09/2013 - 08:52

Yes the switch Port (gig interface 1/0/2) to which the WLAN is connectd is dot1q. i.e., trunk port right....?

find this:

SW1#show interfaces trunk

Port        Mode             Encapsulation  Status        Native vlan

Gi1/0/2     on               802.1q         trunking      1

Port        Vlans allowed on trunk

Gi1/0/2     1-4094

Port        Vlans allowed and active in management domain

Gi1/0/2     1-3

Port        Vlans in spanning tree forwarding state and not pruned

Gi1/0/2     1-3

It is just a basic setup with a single vlan i.e., default vlan 1 and with router, WLAN and acces points.

Stephen Rodriguez Wed, 01/09/2013 - 09:11

pull a show run of the switch, there might be a command that is vlan dot1q tag native.  it changes the behavior of the switch.  If it somehow got enabled, turn it off.

HTH,
Steve

------------------------------------------------------------------------------------------------
Please remember to rate useful posts, and mark questions as answered

amankhang Wed, 01/09/2013 - 20:36

weather dhcp server over ride checked are not but still not able to get the dhcp ip..

as the client laptops wifi adapter says limited connectivity and gets ip address of 169.17.x.x some thing..

i.e., no dhcp ip address.

amankhang Wed, 01/09/2013 - 20:51

will this be the issue as i am using the thwo sets of passwords to get connected to the wifi. (Keysize=104bits, Key Index=1&2, Encryption key=*************, Key format= ASCII)

Correct Answer
kcnajaf@25070 Wed, 01/09/2013 - 21:12

Hi,

Use only Key Index 1.

Try creating an new SSID or may be make this SSID itself for testing with open authetication (Security None) and verify if the DHCP works.

Regards

Najaf

amankhang Wed, 01/09/2013 - 23:10

Solved

Thank you Guys.

Changed the single set index key to access the wifi and got the dhcp working fine....

but recreated agin the same problem in order toconfirm it. as with two set of keys it dosent provide the dhcp itself where as with single set of index key it works fine..

Dont know why there is different set index keys option is it releated to some other things.

Actions

Login or Register to take actions

This Discussion

Posted January 8, 2013 at 6:01 AM
Stats:
Replies:36 Avg. Rating:5
Views:1091 Votes:0
Shares:0
Tags: No tags.

Discussions Leaderboard