cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1110
Views
0
Helpful
4
Replies

Aironet C1140 - dot11radio1 does not work

mrgrn_1981
Level 1
Level 1

Hi

I Have A Cisco Access Point. The exact model is  C1142(AIR-AP1142N-E-K9) and firmware c1140-k9w7-mx.152-2.JB

As you know it has two Radio interface, one for 2.4Ghz and one for 5Ghz

I have set mbssid on both of them and turned the guest mode On in two SSID (one in each of them)

so, normally both of them should be broadcasted and discovered by wireless adapters

and i should add the configuration (authentication method profile and ...) is exactly the same for all of them and both interfaces are up

but the problem is that the SSID set on 5GHz Radio is not broadcasted and worse than that, it is not even functioning when i try to add it manually on a windows client

Am i missing anything in my configuration or ... ?

here is the configuration lines which may be necessary for your troubleshoot

*************************************************************

no ip routing

no ip cef

!

dot11 syslog

!

dot11 ssid TEST

   vlan 400

   authentication open eap eap_methods

   authentication network-eap eap_methods

   authentication key-management wpa version 2

   accounting acct_methods

   dot1x eap profile TEST

   mbssid guest-mode

!

dot11 ssid TEST-Guest

   vlan 450

   authentication open

   mbssid guest-mode

!

dot11 ssid TEST5

   vlan 440

   authentication open eap eap_methods

   authentication network-eap eap_methods

   authentication key-management wpa version 2

   accounting acct_methods

   dot1x eap profile TEST

   mbssid guest-mode

!

!

eap profile TEST

method peap

method mschapv2

!

crypto pki token default removal timeout 0

!

!

!

bridge irb

!

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

encryption vlan 400 mode ciphers aes-ccm

!

encryption vlan 440 mode ciphers aes-ccm

!

encryption vlan 450 key 1 size 40bit CISCOCISCO transmit-key

encryption vlan 450 mode wep mandatory

!

ssid TEST

!

ssid TEST-Guest

!

antenna gain 0

mbssid

station-role root

no cdp enable

!

interface Dot11Radio0.5

encapsulation dot1Q 5 native

no ip route-cache

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Dot11Radio0.400

encapsulation dot1Q 400

no ip route-cache

bridge-group 255

bridge-group 255 subscriber-loop-control

bridge-group 255 spanning-disabled

bridge-group 255 block-unknown-source

no bridge-group 255 source-learning

no bridge-group 255 unicast-flooding

!

interface Dot11Radio0.440

encapsulation dot1Q 440

no ip route-cache

bridge-group 254

bridge-group 254 subscriber-loop-control

bridge-group 254 spanning-disabled

bridge-group 254 block-unknown-source

no bridge-group 254 source-learning

no bridge-group 254 unicast-flooding

!

interface Dot11Radio0.450

encapsulation dot1Q 450

no ip route-cache

bridge-group 253

bridge-group 253 subscriber-loop-control

bridge-group 253 spanning-disabled

bridge-group 253 block-unknown-source

no bridge-group 253 source-learning

no bridge-group 253 unicast-flooding

!

interface Dot11Radio1

no ip address

no ip route-cache

!

encryption vlan 400 mode ciphers aes-ccm

!

encryption vlan 440 mode ciphers aes-ccm

!

encryption vlan 450 key 1 size 40bit CISCOCISCO transmit-key

encryption vlan 450 mode wep mandatory

!

ssid TEST-Guest

!

ssid TEST5

!

antenna gain 0

mbssid

station-role root

no cdp enable

!

interface Dot11Radio1.5

encapsulation dot1Q 5 native

no ip route-cache

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Dot11Radio1.400

encapsulation dot1Q 400

no ip route-cache

bridge-group 255

bridge-group 255 subscriber-loop-control

bridge-group 255 spanning-disabled

bridge-group 255 block-unknown-source

no bridge-group 255 source-learning

no bridge-group 255 unicast-flooding

!

interface Dot11Radio1.440

encapsulation dot1Q 440

no ip route-cache

bridge-group 254

bridge-group 254 subscriber-loop-control

bridge-group 254 spanning-disabled

bridge-group 254 block-unknown-source

no bridge-group 254 source-learning

no bridge-group 254 unicast-flooding

!

interface Dot11Radio1.450

encapsulation dot1Q 450

no ip route-cache

bridge-group 253

bridge-group 253 subscriber-loop-control

bridge-group 253 spanning-disabled

bridge-group 253 block-unknown-source

no bridge-group 253 source-learning

no bridge-group 253 unicast-flooding

!

Power inline negotiation injector installed

****************************************************************************

4 Replies 4

Von Jones
Level 4
Level 4

It appears this post is in the wrong area.  This area is for the Cisco Intelligent Automation for Cloud and Cisco Intelligent Automation for SAP solutions.  You should probably repost the item in another area which the appropriate experts monitor.

Leo Laohoo
Hall of Fame
Hall of Fame

Boot the AP and post the bootup process.

hi leolaohoo

plz answer me in my new post

https://supportforums.cisco.com/thread/2210640

plz answer me in my new post

https://supportforums.cisco.com/thread/2210640

No, I won't. 

I won't respond to your duplicate post(s). 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: