Cisco Aironet AIR-AP1142N-E-K9 5ghz problem

mehdi bahramipour · ‎06-01-2013

hi we have aironet 1142

in FR 2.4 all thing is ok and client connect to ap

but in 5 ghz band , in webbase ap show up up but cliend didnt see the ssid of this ap

plz help

thx

Leo Laohoo · ‎06-01-2013

Sorry, I don't understand what you are trying to say.

Are you saying that your AP is in China? If yes, do you have a WLC?

mehdi bahramipour · ‎06-01-2013

my problem is FR 5 didnt work ,

Leo Laohoo · ‎06-01-2013

What do mean by "FR 5"?

Sent from Cisco Technical Support Nintendo App

mehdi bahramipour · ‎06-01-2013

5 ghz band

Scott Fella · ‎06-01-2013

Post your show version and your show run-config

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***

mehdi bahramipour · ‎06-01-2013

System Software Filename:

c1140-k9w7-tar.152-2.JB

System Software Version:

15.2(2)JB

Bootloader Version:

12.4(23c)JA6

interface Dot11Radio1

no ip address

!

ssid test

!

antenna gain 0

speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6.

m7. m8. m9. m10. m11. m12. m13. m14. m15.

power client 17

channel 5825

station-role root

world-mode dot11d country-code RU both

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

and controller

interface Dot11Radio1

Radio AIR-AP1140A, Base Address 2401.c774.70b0, BBlock version 0.00, Software ve

rsion 4.10.1

Unused dynamic SQRAM memory: 0x00002B4C (10 KB)

Unused dynamic SDRAM memory: 0x00070B98 (450 KB)

Number of supported simultaneous BSSID on Dot11Radio1: 16

*************Carrier Set: China (UNI3) (CN) (-C)*************

Uniform Spreading Required: No

Configured Frequency: 5825 MHz Channel 165

Leo Laohoo · ‎06-01-2013

Post the output to the command "sh ip int brie".

And remove this line: channel 5825

mehdi bahramipour · ‎06-01-2013

ap#show ip int br

Interface IP-Address OK? Method Status Prot

ocol

BVI1 192.168.0.70 YES NVRAM up up

Dot11Radio0 unassigned YES NVRAM up up

Dot11Radio1 unassigned YES NVRAM up up

GigabitEthernet0 unassigned YES NVRAM up up

Scott Fella · ‎06-02-2013

post the wlc show run-config no ap

Thanks,

Scott

Help out other by using the rating system and marking answered questions as "Answered"

-Scott
*** Please rate helpful posts ***

art-barrera · ‎06-02-2013

Given the filename of the code running "w7" indicates standalone deployment. Your interface output shows the 5GHz radio (Dot11Radio1) on so I'm assuming you just can't "see" the SSID from your station. Look at your config under the dot11 ssid "ssid name" section and look for the config statement guest-mode. This will instruct the ap to broadcast the ssid that you defined. I'm assuming that you have a different SSID configured for each radio given that you "see" the ssid under your 2.4GHz radio. //art

Scott Fella · ‎06-02-2013

Haha... Got confused:). Can you post your whole show run-config

Sent from Cisco Technical Support iPhone App

-Scott
*** Please rate helpful posts ***

Abhishek Abhishek · ‎06-02-2013

Hello Mehdi,

As per your query i can suggest you the following solution-

Data Rates Supported in Aironet 1140 Series Access Point

802.11a: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps

802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps

802.11n data rates (2.4 GHz and 5 GHz):

For more information please refer to the link -

http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10092/datasheet_c78-502793.html

Hope this will help you.

mehdi bahramipour · ‎07-08-2013

hi this is my config ,

unfortunately i cant work with 5 ghz band yet pls check this thanks

!

! Last configuration change at 23:23:49 UTC Mon Mar 1 1993

version 15.2

no service pad

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname ap

!

logging rate-limit console 9

enable secret 5 $

no aaa new-model

ip cef

!

dot11 syslog

!

dot11 ssid golestan

authentication open

guest-mode

!

dot11 ssid golestan2

authentication open

guest-mode

!

crypto pki token default removal timeout 0

!

username Cisco password 7 112A1016141D

!

bridge irb

!

interface Dot11Radio0

no ip address

!

ssid golestan2

!

antenna gain 0

station-role root

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Dot11Radio1

no ip address

!

ssid golestan

!

antenna gain 0

speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.

power client 17

channel 5745

station-role root

world-mode dot11d country-code US both

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface GigabitEthernet0

no ip address

duplex auto

speed auto

no keepalive

bridge-group 1

bridge-group 1 spanning-disabled

no bridge-group 1 source-learning

!

interface BVI1

ip address 192.168.0.70 255.255.255.0

!

ip forward-protocol nd

ip http server

no ip http secure-server

ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

ip route 0.0.0.0 0.0.0.0 192.168.0.1

!

snmp-server community cisco RW

bridge 1 route ip

!

wlccp ap username root password 7 06000A25435C08

wlccp ap wds ip address 192.168.0.3

wlccp wds priority 1 interface BVI1

wlccp wnm ip address 192.168.0.3

!

line con 0

line vty 0 4

password 7 01300F175804

login

transport input all

!

end

Leo Laohoo · ‎07-08-2013

Can you please post the following outputs:

1. sh inventory;

2. sh version; and

3. dir