show client ccx rm <mac> status

Unanswered Question
Jul 9th, 2013
User Badges:

Hi there,


I have a WLC 2504 v7.4, AP1602, and a client with CCX v5.

In the WLC, I already enable the CCX Location Measurement from GUI... WIRELESS > 802.11b/g/n > Network

In the WLC, I can see my laptop as a "client" and it shows that my laptop is CCXv5

In the WLC, in the Clients > Detail page, I click the button "Send CCX Req"... wait..then click "Display" wait..wait.. nothing happens.


I then go to the WLC command line, and issue command.... (note that 08:3e:8e:32:19:09 is my laptop wireless adapter MAC)


>show client ccx rm 08:3e:8e:32:19:09 status

Client not in the unicast rm list


What is the "unicast rm list" and how do I put my laptop into the WLC rm list?


Thanks,

[email protected]

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Scott Fella Tue, 07/09/2013 - 05:28
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    The Hall of Fame designation is a lifetime achievement award based on significant overall achievements in the community. 

  • Cisco Designated VIP,

    2017 Wireless

Post the show client detail 08:3e:8e:32:19:09


Thanks,


Scott

Help out other by using the rating system and marking answered questions as "Answered"

sakul tunboonek Tue, 07/09/2013 - 18:44
User Badges:

Hi Scott, thanks and pls find below the result.


(Cisco Controller) >show client detail 08-3E-8E-32-19-09

Client MAC Address............................... 08:3e:8e:32:19:09

Client Username ................................. N/A

AP MAC Address................................... 20:bb:c0:82:ff:80

AP Name.......................................... PSCTH_AP1

Client State..................................... Associated

Client NAC OOB State............................. Access

Wireless LAN Id.................................. 1

Hotspot (802.11u)................................ Not Supported

BSSID............................................ 20:bb:c0:82:ff:80

Connected For ................................... 256 secs

Channel.......................................... 1

IP Address....................................... 172.16.1.250

Gateway Address.................................. Unknown

Netmask.......................................... Unknown

Association Id................................... 6

Authentication Algorithm......................... Open System

Reason Code...................................... 1

Status Code...................................... 0

Session Timeout.................................. 1800

Client CCX version............................... 5

Client E2E version............................... No E2E support

Diagnostics Capability........................... Supported



--More-- or (q)uit

S69 Capability................................... Not Supported

QoS Level........................................ Silver

802.1P Priority Tag.............................. disabled

CTS Security Group Tag........................... Not Applicable

KTS CAC Capability............................... No

WMM Support...................................... Enabled

  APSD ACs.......................................  BK  BE  VI  VO

Power Save....................................... OFF

Current Rate..................................... m7

Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,

    ............................................. 12.0,18.0,24.0,36.0,48.0,

    ............................................. 54.0

Mobility State................................... Local

Mobility Move Count.............................. 0

Security Policy Completed........................ Yes

Policy Manager State............................. RUN

Policy Manager Rule Created...................... Yes

Audit Session ID................................. none

IPv4 ACL Name.................................... none

IPv4 ACL Applied Status.......................... Unavailable

IPv6 ACL Name.................................... none

IPv6 ACL Applied Status.......................... Unavailable

mDNS Status...................................... Disabled



--More-- or (q)uit

mDNS Profile Name................................ none

No. of mDNS Services Advertised.................. 0

Policy Type...................................... N/A

Encryption Cipher................................ None

Protected Management Frame ...................... No

Management Frame Protection...................... No

EAP Type......................................... Unknown

Interface........................................ management

VLAN............................................. 0

Quarantine VLAN.................................. 0

Access VLAN...................................... 0

Client Capabilities:

      CF Pollable................................ Not implemented

      CF Poll Request............................ Not implemented

      Short Preamble............................. Implemented

      PBCC....................................... Not implemented

      Channel Agility............................ Not implemented

      Listen Interval............................ 5

      Fast BSS Transition........................ Not implemented

Client Wifi Direct Capabilities:

      WFD capable................................ No

      Manged WFD capable......................... No

      Cross Connection Capable................... No



--More-- or (q)uit

      Support Concurrent Operation............... No

Fast BSS Transition Details:

Client Statistics:

      Number of Bytes Received................... 377711

      Number of Bytes Sent....................... 2315955

      Number of Packets Received................. 2747

      Number of Packets Sent..................... 3214

      Number of Interim-Update Sent.............. 0

      Number of EAP Id Request Msg Timeouts...... 0

      Number of EAP Id Request Msg Failures...... 0

      Number of EAP Request Msg Timeouts......... 0

      Number of EAP Request Msg Failures......... 0

      Number of EAP Key Msg Timeouts............. 0

      Number of EAP Key Msg Failures............. 0

      Number of Data Retries..................... 293

      Number of RTS Retries...................... 0

      Number of Duplicate Received Packets....... 1

      Number of Decrypt Failed Packets........... 0

      Number of Mic Failured Packets............. 0

      Number of Mic Missing Packets.............. 0

      Number of RA Packets Dropped............... 0

      Number of Policy Errors.................... 0

      Radio Signal Strength Indicator............ -47 dBm



--More-- or (q)uit

      Signal to Noise Ratio...................... 49 dB

Client Rate Limiting Statistics:

      Number of Data Packets Recieved............ 0

      Number of Data Rx Packets Dropped.......... 0

      Number of Data Bytes Recieved.............. 0

      Number of Data Rx Bytes Dropped............ 0

      Number of Realtime Packets Recieved........ 0

      Number of Realtime Rx Packets Dropped...... 0

      Number of Realtime Bytes Recieved.......... 0

      Number of Realtime Rx Bytes Dropped........ 0

      Number of Data Packets Sent................ 0

      Number of Data Tx Packets Dropped.......... 0

      Number of Data Bytes Sent.................. 0

      Number of Data Tx Bytes Dropped............ 0

      Number of Realtime Packets Sent............ 0

      Number of Realtime Tx Packets Dropped...... 0

      Number of Realtime Bytes Sent.............. 0

      Number of Realtime Tx Bytes Dropped........ 0

Nearby AP Statistics:

      PSCTH_AP1(slot 0)

        antenna0: 190 secs ago................... -50 dBm

        antenna1: 190 secs ago................... -47 dBm

DNS Server details:



--More-- or (q)uit

      DNS server IP ............................. 0.0.0.0

      DNS server IP ............................. 0.0.0.0

Assisted Roaming Prediction List details:





Client Dhcp Required:     True



(Cisco Controller) >

Saurav Lodh Tue, 07/09/2013 - 19:12
User Badges:
  • Gold, 750 points or more

For your information, 2 CCX enabled clients per AP are supported at max. When you issued show client ccx rm status, it revealed , that particular client has not received any unicast request from AP. For more info refer below


http://www.cisco.com/en/US/docs/wireless/controller/7.4/configuration/guides/consolidated/b_cg74_CONSOLIDATED_chapter_010000111.html#ID2083

sakul tunboonek Tue, 07/09/2013 - 21:09
User Badges:

Hi, thanks Scott and Saurav... yes, I have enable the RM. I have followed the docs in your link.. however, seem like the AP still does not send out any unicast request..


note: in Step3 in the document, it guide to issue command >config client location-calibration {enable | disable} client _mac interval_seconds but my WLC_2504 does not support this command.



(Cisco Controller) >config advanced 802.11b ccx location-meas global enable 60



No change - configured values are same as previous





(Cisco Controller) >config advanced 802.11b ccx customize PSCTH_AP1 on



Operation completed successfully





(Cisco Controller) >config advanced 802.11b ccx location-meas ap PSCTH_AP1 enable 60



Cisco AP CCX options set



Operation completed successfully



(Cisco Controller) >config client ?



ccx            Configure Cisco Client Extension(CCX) diagnostic options.

deauthenticate Disconnects a client.



(Cisco Controller) >config client ccx ?



clear-reports  Clear all stored Client Profile Information.

clear-results  Clear All test Results.

default-gw-ping Send request to perform Default Gateway Ping test.

dhcp-test      Send request to perform DHCP test.

dns-ping       Send request to perform DNS Server Ping test.

dns-resolve    Send request to perform DNS Name Resolution test.

get-client-capability Send a request to get Client's Capabilty Info.

get-manufacturer-info Send a request to get Client's Manufactured Info.

get-operating-parameters Send a request to get Client's Current  Operating Parameters.

get-profiles   Send a request to get Client Profiles.

log-request    Send a CCX Log Request.

send-message   Send a message to the Client,

stats-request  Send a CCX Client Statistics Request.

test-abort     Abort the Current test.

test-association Send request to perform Association test.

test-dot1x     Send request to perform 802.1x test.

test-profile   Send request to perform Profile Redirect test.



(Cisco Controller) >show advanced 802.11b ccx global

  802.11b Client Beacon Measurements:

    enabled with (interval=60) seconds



(Cisco Controller) >show advanced 802.11b ccx ap PSCTH_AP1

  802.11b Client Beacon Measurements for Cisco AP:

    enabled with (interval=60) seconds



(Cisco Controller) >show ap ccx rm PSCTH_AP1 status





B Radio



  Beacon Request................................. Disabled

  Channel Load Request........................... Disabled

  Frame Request.................................. Disabled

  Noise Histogram Request........................ Disabled

  Path Loss Request.............................. Disabled

  Interval....................................... 60

  Iteration...................................... 0



                                                   A Radio



  Beacon Request................................. Disabled

  Channel Load Request........................... Disabled

  Frame Request.................................. Disabled

  Noise Histogram Request........................ Disabled

  Path Loss Request.............................. Disabled

  Interval....................................... 60

  Iteration...................................... 0



(Cisco Controller) >



(Cisco Controller) >show client ccx rm 08-3E-8E-32-19-09 status

Client not in the unicast rm list



(Cisco Controller) >

Actions

This Discussion

Related Content

 

 

Trending Topics: Other Wireless Mobility

client could not be authenticated
Network Analysis Module (NAM) Products
Cisco 6500 nam
reason 440 driver failure
Cisco password cracker
Cisco Wireless mode