×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.
Jonathan Schulenberg Tue, 08/13/2013 - 06:03
User Badges:
  • Super Bronze, 10000 points or more
  • Cisco Designated VIP,

    2017 IP Telephony

Check under voice register global. I don't have a CME box in front of me but at least url directory exists there in the CME Admin Guide; I would expect other keywords to as well.


conf t

voice register global

url idle http://XXX/idle.php idle-timeout 5



Please remember to rate helpful responses and identify helpful or correct answers.

michaelngai Thu, 08/15/2013 - 15:49
User Badges:

Hi Jonathan, thank you for the response.  I've tried that but there's no such commands under "voice register global", nothing seemed remotely close to it.


CME(config-register-global)#?

voice register global configuration commands:

  application              Define application

  attempted-registrations  Define size of the attempted-registrations table

  authenticate             Define auth mode for SIP CME/SRST

  bandwidth                allow SIP SDP bandwidth related options

  call-forward             Decide call forward parameters for an SIP phone

  default                  Set a command to its defaults

  dialplan-pattern         Define E.164 telephone number prefix

  exit                     Exit from voice register global configuration mode

  external-ring            Set external ringing to be included into alert-info

  fac                      Voice register global FAC setup

  ip                       Set ip packet options

  max-dn                   Define max number of dn

  max-pool                 Define max number of pool

  mode                     Define mode: CME/SRST

  mwi                      MWI service in SRST mode

  no                       Negate a command or set its defaults

  outbound-proxy           Configure an Outbound Proxy Server

  overlap-signal           Configure Overlap Signaling support

  service                  Service configuration in voice reg global

  system                   Define system message

  timeouts                 Define timeout value for sip phone

  timezone                 Set timezone for SIP Phones


I have tried putting it under "telephony-service" but being a SIP phone it didn't pick it up there.


I'm ok if it's not supported under CME but just wanted some confirmation.

brmeade Thu, 08/15/2013 - 16:45
User Badges:
  • Silver, 250 points or more

Michael,


This guide- http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/command/reference/cme_u1ht.html#wp1016489
shows that some CME versions have a URL command under voice register global but it doesn't seem that it there is idle URL in any CME version for SIP.


It may just be one of the things that applies from telephony service.  Did you try regenerating the CNF Files afterwards?


Brian

michaelngai Sat, 08/17/2013 - 04:33
User Badges:

Hi Brian, sorry previous output I didn't fully enable SIP.  URL command does exist and after drilling deeper into the command there doesn't seemed to be anything related to idle URL. 


I did regenerate CNF Files and SIP profiles after enabling it under "telephony service", I rebooted the handsets too but they don't seemed to acknowledge "url idle".


The php script is dedinately valid, I tried enabling it under the "service url" button and the 9971 would correctly load the page after pressing the service button.


CME(config-register-global)#?

voice register global configuration commands:

  application              Define application

  apply-config             apply config for the 99/89 phones, restart all other sip phones

  attempted-registrations  Define size of the attempted-registrations table

  authenticate             Define auth mode for SIP CME/SRST

  bandwidth                allow SIP SDP bandwidth related options

  bulk                     Define a pattern for bulk registration

  call-feature-uri         Define TNP SIP phone's Call Feature URI

  call-forward             Decide call forward parameters for an SIP phone

  camera                   Enable camera

  conference               Configure conference type for adhoc

  create                   Create profile for SIP phone

  date-format              Set date format for IP Phone display

  default                  Set a command to its defaults

  dialplan-pattern         Define E.164 telephone number prefix

  dst                      Enable / define daylight saving time

  exit                     Exit from voice register global configuration mode

  external-ring            Set external ringing to be included into alert-info

  fac                      Voice register global FAC setup

  file                     Enable generation of the text profile

  forwarding               Decide if forwarding local is enabled for SIP phone

  hold-alert               Enable On-Hold alert for SIP phone

  ip                       Set ip packet options

  load                     Select the firmware load file

  logo                     Define logo url that will be used by SIP phone

  max-dn                   Define max number of dn

  max-pool                 Define max number of pool

  mode                     Define mode: CME/SRST

  mwi                      Generate stutter tone for SIP mwi

  network-locale           Define network locale

  no                       Negate a command or set its defaults

  ntp-server               Define NTP server address for TNP phones

  olsontimezone            Set olson timezone for IP Phones

  outbound-proxy           Configure an Outbound Proxy Server

  overlap-signal           Configure Overlap Signaling support

  phone-redirect-limit     Define max number of redirect per call for SIP phone

  privacy                  Enable privacy for SIP shared-line phone

  privacy-on-hold          Enable privacy-on-hold for SIP shared-line phone

  reset                    Reset all SIP phones

  restart                  restart all SIP phone

  service                  Service configuration in voice reg global

  source-address           Define IP address and port for SIP CME

  tftp-path                Define tftp path for SIP CME

  time-format              Set time format for IP Phone display

  timeouts                 Define timeout value for sip phone

  timezone                 Set timezone for SIP Phones

  upgrade                  Generate OS79XX.TXT for firmware upgrade

  url                      Define SIP phone URL's

  user-locale              Define SIP Phone user locale

  video                    Enable video

  voicemail                Set the voicemail access number called when the messages button is pressed



CME(config-register-global)#url ?

  authentication  authentication url

  directory       directory url

  service         service url

Actions

This Discussion