×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Cisco AIR-LAP1252AG-A-K9

Unanswered Question
Aug 15th, 2013
User Badges:

I am working with a AIR-LAP1252AG-A-K9. It currently has a password set for it that I do not know.


The reset to factory defaults instructions off the cisco software configuration guide simply states "when the access point reboots and the summary status screen appears, type :resetall, and press enter." my understanding from the manual you have 2 mintues to do this once you have a cli prompt and after the ap has booted it should display a status screen.  I however only seem to get a login screen.


Can someone please help me reset this AP to factory defaults so that I may test and configure it?




IOS Bootloader - Starting system.

Xmodem file system is available.

flashfs[0]: 153 files, 8 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 31868928

flashfs[0]: Bytes used: 8750080

flashfs[0]: Bytes available: 23118848

flashfs[0]: flashfs fsck took 17 seconds.

Reading cookie from flash parameter block...done.

Base Ethernet MAC address: 1c:df:0f:c3:38:ae

Loading "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"...#######

################################################################################

################################################################################

###########################################


File "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3" uncompressed

and installed, entry point: 0x3000

executing...


              Restricted Rights Legend


Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.


           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706




Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEAS

E SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2009 by Cisco Systems, Inc.

Compiled Sun 07-Jun-09 03:50 by prod_rel_team

Image text-base: 0x00003000, data-base: 0x01000000


Initializing flashfs...


flashfs[1]: 153 files, 8 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 31868928

flashfs[1]: Bytes used: 8750080

flashfs[1]: Bytes available: 23118848

flashfs[1]: flashfs fsck took 4 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.


Warning:  the compile-time code checksum does not appear to be present.

Radio 1 A600 8000 0 0 A8030000 30

Radio 1 A600 8000 0 0 B8030000 13

tx_paks 1293

tx_paks 646


This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.


A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html


If you require further assistance please contact us by sending email to

export@cisco.com.


cisco AIR-LAP1252AG-A-K9   (PowerPC 8349) processor (revision C0) with 49142K/16

384K bytes of memory.

Processor board ID FTX144390KE

PowerPC 8349 CPU at 533Mhz, revision number 0x0031

Last reset from power-on

1 Gigabit Ethernet interface

2 802.11 Radio(s)


32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 1C:DF:0F:C3:38:AE

Part Number                          : 73-10425-06

PCA Assembly Number                  : 800-27630-06

PCA Revision Number                  : B0

PCB Serial Number                    : FOC14390WYP

Top Assembly Part Number             : 800-29536-03

Top Assembly Serial Number           : FTX144390KE

Top Revision Number                  : A0

Product/Model Number                 : AIR-LAP1252AG-A-K9

The name for the keys will be: ap01.u00924.albertsons.com


% The key modulus size is 1024 bits

% Generating 1024 bit RSA keys, keys will be non-exportable...[OK]




Press RETURN to get started!



otCisco Systems, Inc.

Compiled Sun 07-Jun-09 03:50 by prod_rel_team

*Jun  1 08:25:45.047 MDT: %SNMP-5-COLDSTART: SNMP agent on host ap01 is undergoi

ng a cold start

*Jun  1 08:25:46.083 MDT: %IP_SNMP-3-SOCKET: can't open UDP socket

*Jun  1 08:25:46.083 MDT: Unable to open socket on port 161

*Jun  1 08:25:46.083 MDT: %SSH-5-ENABLED: SSH 1.99 has been enabled

*Jun  1 08:25:46.083 MDT: %LINK-5-CHANGED: Interface Dot11Radio0, changed state

to administratively down

*Jun  1 08:25:47.287 MDT: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11R

adio0, changed state to down

*Jun  1 08:25:49.267 MDT: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inl

ine power source

*Jun  1 08:25:52.839 MDT: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP a

ddress 192.168.0.143, mask 255.255.255.0, hostname ap01



User Access Verification


Username: resetall

Password:


% Authentication failed


Username:

Username:

Username:

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Leo Laohoo Thu, 08/15/2013 - 16:08
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    The Hall of Fame designation is a lifetime achievement award based on significant overall achievements in the community. 

  • Cisco Designated VIP,

    2017 LAN, Wireless

There's a method but it means it will erase your config.  You want that?

djelizondo Thu, 08/15/2013 - 16:12
User Badges:

Yes please. I do not care about erasing the config. As these units need to be fully tested and restored to factory defaults anyways. They can be reconfigured once they are put back into the field.

Leo Laohoo Thu, 08/15/2013 - 16:31
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    The Hall of Fame designation is a lifetime achievement award based on significant overall achievements in the community. 

  • Cisco Designated VIP,

    2017 LAN, Wireless

I do not care about erasing the config.

Ahhhh ... Music to my ears.



Using a TFTP Server to Return to a Previous Release

djelizondo Fri, 08/16/2013 - 10:14
User Badges:

I dont get it I get this error whenever trying to download software.




Service Contract RequiredClose
 
ErrorTo Download this software, you must have a valid service contract associated to your Cisco.com profile.
If you do not have a service contract you can get one through:

  • Your Cisco Account Team if you have a direct purchase agreement with Cisco

  • Your Cisco Partner or Reseller
Once you have the service contract you must associate your service contract to your Cisco.com user ID with Profile Manager




Is there anywhere I can get this software to flash it for free?

Actions

This Discussion

Related Content