×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

nexus 5548up loader> how to resolve this issue?

Answered Question
Sep 4th, 2013
User Badges:

loader> dir

bootflash:

  lost+found

  n5000-uk9-kickstart.5.1.3.N1.1a.bin

  n5000-uk9.5.1.3.N1.1a.bin

  mts.log

  vdc_2

  vdc_3

  vdc_4

  vlan.dat

  MDS201309012310597480.lic


loader> boot n5000-uk9-kickstart.5.1.3.N1.1a.bin


Cisco Nexus Operating System (NX-OS) Software

TAC support: http://www.cisco.com/tac

Copyright (c) 2002-2012, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

switch(boot)#



How to recover from the mode

after reload the switch its going back to loader>

Correct Answer by InayathUlla Sharieff about 3 years 11 months ago

Rupesh,

I just finished from the same situation and resolved it

Please follow th document mentioned below;

http://www.cisco.com/en/US/docs/switches/datacenter/sw/password_recovery/nx_os_pw.html


Step 14 Boot the Cisco NX-OS kickstart image on the standby supervisor module, if necessary.

In the following example, the kickstart image filename is nx-os_kickstart.bin:

loader# boot bootflash:nx-os_kickstart.bin


Step 15 Load the Cisco NX-OS system software on the standby supervisor module, if necessary.

In the following example, the system image filename is nx-os.bin:

switch(boot)# load bootflash:nx-os.bin


Step 16 Save the configuration.




HTH

Regards

Inayath

***Plz  don't forget to rate this post if this info is helpfull***************

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Marvin Rhoads Thu, 09/05/2013 - 06:02
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 Firewalling, Network Management, VPN

Start with:


boot n5000-uk9-kickstart.5.1.3.N1.1a.bin


After that completes:


load n5000-uk9.5.1.3.N1.1a.bin

Correct Answer
InayathUlla Sharieff Wed, 09/04/2013 - 23:56
User Badges:
  • Cisco Employee,

Rupesh,

I just finished from the same situation and resolved it

Please follow th document mentioned below;

http://www.cisco.com/en/US/docs/switches/datacenter/sw/password_recovery/nx_os_pw.html


Step 14 Boot the Cisco NX-OS kickstart image on the standby supervisor module, if necessary.

In the following example, the kickstart image filename is nx-os_kickstart.bin:

loader# boot bootflash:nx-os_kickstart.bin


Step 15 Load the Cisco NX-OS system software on the standby supervisor module, if necessary.

In the following example, the system image filename is nx-os.bin:

switch(boot)# load bootflash:nx-os.bin


Step 16 Save the configuration.




HTH

Regards

Inayath

***Plz  don't forget to rate this post if this info is helpfull***************

Actions

This Discussion