×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Agents become not ready after ring no answer !

Unanswered Question
Sep 19th, 2013
User Badges:

Hi,guys .

Agents become not ready after ring no answer even though i have configured the service parameter of :


Agent state after ring no answer : to be Ready always instead of the default of not ready.


Thanks in advance

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Carlo Poggiarelli Thu, 09/19/2013 - 01:41
User Badges:
  • Green, 3000 points or more

Hi Ahmed.

Wich platform and version are you running?


THX


Regards


Carlo



Please rate all helpful posts

"The more you help the more you learn"

Ahmed Awida Thu, 09/19/2013 - 01:50
User Badges:

Hi Carlo.

UCS C24 M3,

UCCX :

System version: 9.0.1.10000-100.


If i make any reset or restart to the phones,will this make the agent in not ready state ?


Thanks.

Carlo Poggiarelli Thu, 09/19/2013 - 02:11
User Badges:
  • Green, 3000 points or more

Hi Ahmed.

No if you reset the phone yuo make the device unavailable to the CAD so it goes on disconnected mode.



restart Cisco Desktop Sync Service and Cisco Desktop Enterprise Service under uccx serviceability -->tools-->>network services


HTH


Regards


Carlo





Please rate all helpful posts

"The more you help the more you learn"

Ahmed Awida Thu, 09/19/2013 - 02:17
User Badges:

Hi Carlo.

I am not using CAD ,i am using ip phone agent.

ganapathi s Thu, 09/19/2013 - 10:09
User Badges:

Hi Ahmed,


Did u try restarting the PG service once.



Regards,

Ganapathi.S

Jason Hutchinson Thu, 09/19/2013 - 10:13
User Badges:
  • Cisco Employee,

Please keep in mind:


In an extreme situation, if there is only one agent in the Ready state, the specific call, which the lone agent did not answer previously, continues to queue to the lone agent in a recursive manner until the agent answers the call or logs out.

Neal haas Sat, 09/21/2013 - 08:36
User Badges:

If you wait, say 5 minutes, does it come back to active? What is the Wrap-Up timer set to?

dshumake Sun, 09/22/2013 - 11:47
User Badges:

I am also having this issue:


But I have two queues,  agent 1 in CNC1,  agent 2 CNC2...


Calls come into CNC1,  ring not answer...   agent 1 will go to not ready.  Call will then goes to CNC2...  OK

So how can I set it up so that agent 1 will go back to ready state. 


     the problem the agent is busy and does not realize that they have been put in to not ready state.



If I change the system parm to the ring no answer to all go back to ready. then the call will never reach CNC2


thanks


using uccx 9

Kartik Bhatia Sun, 09/22/2013 - 16:08
User Badges:

On the point - If I change the system parm to the ring no answer to all go back to ready. then the call will never reach CNC2


If the agent goes into Reserver and then Ringing and then RONAs - will this not put him on the bottom of teh Longest Idle list anyways - or you sing Most Skilled Routing?


I wonder if there is a way to disbale this in UCCE.

Gaurav Purohit Wed, 09/25/2013 - 21:31
User Badges:

Hi,

I believe this is a default behavior to put agents into not ready. This helps the system to avoid sending subsequent calls to "Not Available" agent and to correctly calculate things like Estimate Wait Time for the Queue.


I don't think it can be overridden, still curious to know otherwise.

Actions

This Discussion