cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
9775
Views
0
Helpful
4
Replies

Nexus 7000 6.2.2 xcvrInval

csco10387876
Level 1
Level 1

Good evening,

after upgrading some 7K from 6.1 to 6.2.2 we encounter the following issue

interface go in xcvrInval state and nothing we do can change it unless changing to a fet or 1G spf.

The same optic in a 6.1 chassi is seen correctly.

xcvrInval is seen on any interface config, from fabricpath to a routed interface.

any advice would be welcome.

4 Replies 4

Hi,

I would appreciate if you could get some information in regards of this situation.

sh int e x/x transceiver details

Sh run int ex/x

sh version

What type of transceiver is been use in there?

Could you test those trasnceivers on any other port?

Regards,

Robert Rodriguez

Hello Roberto,

Here are the outpur you asked ;-)

Ethernet1/8

    transceiver is present

    type is 10Gbase-SR

    name is Solid-Optics

    part number is SFP-10G-SR+-SO

    revision is 2.0

    serial number is SO120806478

    nominal bitrate is 10300 MBit/sec

    cisco id is --

    cisco extended id number is 4

    number of lanes 1

           SFP Detail Diagnostics Information (internal calibration)

  ----------------------------------------------------------------------------

                Current              Alarms                  Warnings

                Measurement     High        Low         High          Low

  ----------------------------------------------------------------------------

  Temperature   28.73 C        90.00 C    -10.00 C     85.00 C       -5.00 C

  Voltage        3.30 V         3.59 V      3.00 V      3.50 V        3.04 V

  Current           N/A        50.00 mA     1.00 mA    40.00 mA       2.00 mA

  Tx Power          N/A        20.99 dBm   10.70 dBm   20.00 dBm     11.69 dBm

  Rx Power      18.21 dBm      20.99 dBm    6.90 dBm   20.00 dBm      7.90 dBm

  Transmit Fault Count = 0

  ----------------------------------------------------------------------------

  Note: ++  high-alarm; +  high-warning; --  low-alarm; -  low-warning

****************************************

interface Ethernet1/8

  description SwDCSmaD02IN

  switchport

  switchport mode fabricpath

  medium p2p

  no shutdown

****************************************

Cisco Nexus Operating System (NX-OS) Software

TAC support: http://www.cisco.com/tac

Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.ht

ml

Copyright (c) 2002-2013, Cisco Systems, Inc. All rights reserved.

The copyrights to certain works contained in this software are

owned by other third parties and used and distributed under

license. Certain components of this software are licensed under

the GNU General Public License (GPL) version 2.0 or the GNU

Lesser General Public License (LGPL) Version 2.1. A copy of each

such license is available at

http://www.opensource.org/licenses/gpl-2.0.php and

http://www.opensource.org/licenses/lgpl-2.1.php

Software

  BIOS:      version 2.12.0

  kickstart: version 6.2(2)

  system:    version 6.2(2)

  BIOS compile time:       05/29/2013

  kickstart image file is: bootflash:///n7000-s2-kickstart.6.2.2.bin

  kickstart compile time:  7/9/2013 20:00:00 [08/22/2013 06:51:27]

  system image file is:    bootflash:///n7000-s2-dk9.6.2.2.bin

  system compile time:     7/9/2013 20:00:00 [08/22/2013 10:07:03]

Hardware

  cisco Nexus7000 C7010 (10 Slot) Chassis ("Supervisor Module-2")

  Intel(R) Xeon(R) CPU         with 32745068 kB of memory.

  Processor Board ID JAF1632BFTJ

  Device name: SwDcSmaRIN

  bootflash:    2007040 kB

  slot0:              0 kB (expansion flash)

Kernel uptime is 2 day(s), 18 hour(s), 12 minute(s), 34 second(s)

Last reset

  Reason: Unknown

  System version: 6.1(1)

  Service:

plugin

  Core Plugin, Ethernet Plugin

****************************************

spf type is 10G spf+ SR from solid optics, we have the same problem with option from other manufacturers, only when using a cisco branded optic does it work.

****************************************

loss of link or shut of an interface that is currently working (after ISSU from 6.1.1  to 6.2.2) change the state from valid to invalid.

Regards,

Hi,

I have a similar problem since the upgrade to 6.2.2.

Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_serie
s_home.html
Copyright (c) 2002-2013, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained in this software are
owned by other third parties and used and distributed under
license. Certain components of this software are licensed under
the GNU General Public License (GPL) version 2.0 or the GNU
Lesser General Public License (LGPL) Version 2.1. A copy of each
such license is available at
http://www.opensource.org/licenses/gpl-2.0.php and
http://www.opensource.org/licenses/lgpl-2.1.php

Software
  BIOS:      version 2.12.0
  kickstart: version 6.2(2a)
  system:    version 6.2(2a)
  BIOS compile time:       05/29/2013
  kickstart image file is: bootflash:///n7000-s2-kickstart.6.2.2a.bin
  kickstart compile time:  8/23/2013 15:00:00 [10/14/2013 23:54:28]
  system image file is:    bootflash:///n7000-s2-dk9.6.2.2a.bin
  system compile time:     8/23/2013 15:00:00 [10/15/2013 03:58:57]


Hardware
  cisco Nexus7000 C7004 (4 Slot) Chassis ("Supervisor Module-2")
  Intel(R) Xeon(R) CPU         with 12224956 kB of memory.

  bootflash:    2007040 kB
  slot0:        7989768 kB (expansion flash)

Kernel uptime is 0 day(s), 1 hour(s), 8 minute(s), 14 second(s)

Last reset at 773401 usecs after  Sat Nov 23 14:53:21 2013

  Reason: Reset triggered due to Switchover Request by User
  System version: 6.1(4a)
  Service: SAP(93): Swover due to install

plugin
  Core Plugin, Ethernet Plugin

Ethernet4/25 is down (Transceiver validation failed)

admin state is up, Dedicated Interface

Ethernet4/25

    transceiver is present

    type is 10Gbase-SR

    name is CISCO-AVAGO

    part number is SFP-10G-SR

    revision is V03

    serial number is AGD1603405J

    nominal bitrate is 10300 MBit/sec

    Link length supported for 50/125um OM3 fiber is 300 m

    cisco id is --

    cisco extended id number is 4

    cisco part number is 10-2415-03

    cisco product id is SFP-10G-SR

    cisco vendor id is V03

Hi Gilles,

you need to make sure you have the following command :

"service unsupported-transceiver", I guess you are using 3-party transceivers too.

Regards,

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: