2620Xm and a nm-2fe2w

Unanswered Question
Oct 27th, 2013
User Badges:

I am having difficulty getting these two to play nicely. My router has 128 memory and 32 flash. Thr card has a solid light until the ios finishes booting and then it dims. I have the 12.4T advanced enterprise ios. Exact IOS escapes me right now but all I should require is the 12.2(8)T IOS. On boot IOS reports an Unknown device. Show diag provides the card information and part number but lists the port disabled (216). Has any one gotten these devices to work together? If so, could you tell me the IOS that worked? Is there something special that has to be done for this card to be installed? Thank you very much!

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
andyurban1 Mon, 10/28/2013 - 03:30
User Badges:

I have the output of my router here, just to clarify it is the v1 and not the v2 of this module.


Smart Init is enabled

smart init is sizing iomem

  ID            MEMORY_REQ                 TYPE

00036C          0X000B3B80 C2620XM Single Fast Ethernet

0000D8           UNKNOWN port adapter

                0X00098670 public buffer pools

                0X00211000 public particle pools

TOTAL:          0X0035D1F0



Cisco IOS Software, C2600 Software (C2600-SPSERVICESK9-M), Version 12.4(15)T14


Cisco 2620XM (MPC860P) processor (revision 1.0) with 127627K/3445K bytes of memo

ry.

Processor board ID JAD07070TZU

M860 processor: part number 5, mask 2

1 FastEthernet interface

1 Serial interface

32K bytes of NVRAM.

32768K bytes of processor board System flash (Read/Write)



Mar  1 00:00:09.915: %PA-3-NOTSUPPORTED: PA in slot1 (Unknown (type 216)) is no

t supported on this image.

           Please issue "show diag" in fully loaded IOS image

           to get the PA's information and verify if it is supported

           by this image, a newer version may be needed.



Slot 1:

        Unknown (type 216) Port adapter

        Port adapter is disabled

        Port adapter insertion time unknown

        EEPROM contents at hardware discovery:

        Hardware Revision        : 1.0

        Top Assy. Part Number    : 800-04797-01

        Board Revision           : F0

        Deviation Number         : 0-8707

        Fab Version              : 05

        PCB Serial Number        : JAD05310GPC

        RMA Test History         : 00

        RMA Number               : 0-0-0-0

        RMA History              : 00

        Product (FRU) Number     : NM-2FE2W=

        EEPROM format version 4

andyurban1 Mon, 10/28/2013 - 04:01
User Badges:

I was reading this,


http://www.cisco.com/en/US/prod/collateral/routers/ps259/product_data_sheet09186a00801aa71c.html


Looking at it seems like it would be compatible, Is table five only refering to the 2m? Do you have any recommendation on how to get an additional FastEthernet port? I am studying for my CCNA and would like to get connectivity to my Cable internet. I actually have 2 2620XM's thank you!

johnlloyd_13 Mon, 10/28/2013 - 04:38
User Badges:
  • Blue, 1500 points or more

Hi,

It looks like there might be some inconsistencies in the docs. Did you try to install it on the other router and was able to detect it?

Otherwise you can opt for an NM-1E. Was recently browsing through the 2600XM series and I always go for at least 2 FE ports. I'm eyeing for an 2651XM for a FR switch or terminal server.

http://www.cisco.com/en/US/products/hw/routers/ps274/products_data_sheet...

Sent from Cisco Technical Support iPhone App

Actions

This Discussion

Related Content