×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Dial peer for variable length numbers in Germany and Interdigit Timeout (CME)

Answered Question
Nov 13th, 2013
User Badges:

Hi,


I'm using CME 8.6 with a VIC2-2BRI on an ISDN BRI line. Because of the variable length numbers in Germany a use .T as my destination pattern in the ISDN dial peer. If a dial a number, it takes 10 seconds before the call gets placed. If I dial # at the end of the number, the calls gets placed immediately. I understand that this behaviour is controlled by the interdigit timer? I set it to 2 seconds under my voice port, but it still takes 10 seconds for the router to dial.


interface BRI0/0/0

description CONNECTION_TO_NTBA

no ip address

isdn switch-type basic-net3

isdn overlap-receiving T302 3000

isdn point-to-point-setup

isdn incoming-voice voice


voice-port 0/0/0

translation-profile incoming ADD_LEADING_ZERO_INCOMING_ISDN

compand-type a-law

no comfort-noise

cptone DE

timeouts interdigit 2

description ISDN_SPEECH

bearer-cap Speech


dial-peer voice 10 pots

description INCOMING_AND_OUTGOING_ISDN_CALLS

translation-profile incoming INCOMING_ISDN_CALLS

translation-profile outgoing OUTGOING_ISDN_CALLS

incoming called-number 800XX[YZ]

destination-pattern .T

no digit-strip

port 0/0/0

no sip-register

Correct Answer by Amine Nouasri about 3 years 9 months ago

then set the timer manually. Uner Telephony-service

timeouts interdigit x (value in seconds)


Please rate helpful answers!

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Amine Nouasri Wed, 11/13/2013 - 11:09
User Badges:
  • Bronze, 100 points or more

Do you have any timer set under telephony-service? Please post your running-config here.

Correct Answer
Amine Nouasri Wed, 11/13/2013 - 11:45
User Badges:
  • Bronze, 100 points or more

then set the timer manually. Uner Telephony-service

timeouts interdigit x (value in seconds)


Please rate helpful answers!

johannesmoos Wed, 11/13/2013 - 11:56
User Badges:

Thanks, I guess I just set the timer in the wrong place.
Now I set it under 'telephone-service' for SCCP and under 'voice-register-global' for SIP. Works as expected.

Carlo Poggiarelli Wed, 11/13/2013 - 11:51
User Badges:
  • Green, 3000 points or more

Hi.
Can you please collect debug vpm all and debug isdn q931 while dialing out without pressing #

Thanks

Carlo

Sent from Cisco Technical Support iPhone App

johannesmoos Wed, 11/13/2013 - 12:08
User Badges:

Of course:


000451: Nov 13 2013 21:06:14.277 CET: ISDN BR0/0/0 Q931: RX <- FACILITY pd = 8  callref = N/A

    Facility i = 0x91A10F02024275060604008267010A020101

        Protocol Profile = Remote Operations Protocol

        0xA10F02024275060604008267010A020101

        Component = Invoke component

             3PTY Request

    Called Party Number i = 0xA1, '2774XXXXXX'

        Plan:ISDN, Type:National

000452: Nov 13 2013 21:06:15.517 CET: ISDN BR0/0/0 Q931: Applying typeplan for sw-type 0x1 is 0x0 0x0, Calling num 02774XXXXXX

000453: Nov 13 2013 21:06:15.517 CET: ISDN BR0/0/0 Q931: Sending SETUP  callref = 0x0018 callID = 0x801E switch = basic-net3 interface = User

000454: Nov 13 2013 21:06:15.521 CET: ISDN BR0/0/0 Q931: TX -> SETUP pd = 8  callref = 0x18

    Bearer Capability i = 0x8090A3

        Standard = CCITT

        Transfer Capability = Speech 

        Transfer Mode = Circuit

        Transfer Rate = 64 kbit/s

    Channel ID i = 0x81

        Preferred, B1

    Calling Party Number i = 0x0080, '02774XXXXXX'

        Plan:Unknown, Type:Unknown

    Called Party Number i = 0x80, '02774XXXXXX'

        Plan:Unknown, Type:Unknown

000455: Nov 13 2013 21:06:15.761 CET: ISDN BR0/0/0 Q931: RX <- SETUP_ACK pd = 8  callref = 0x98

    Channel ID i = 0x89

        Exclusive, B1

000456: Nov 13 2013 21:06:16.093 CET: ISDN BR0/0/0 Q931: RX <- ALERTING pd = 8  callref = 0x98

    Facility i = 0x91A10F0202447F0606040082670101020101

        Protocol Profile = Remote Operations Protocol

        0xA10F0202447F0606040082670101020101

        Component = Invoke component

             3PTY Request

    Progress Ind i = 0x8288 - In-band info or appropriate now available 

    Display i = 'CCNR moeglich'

000457: Nov 13 2013 21:06:16.101 CET: mars_flex_dsprm_current_codec_comp:DSP:0 FLEX Complexity Codec

000458: Nov 13 2013 21:06:16.105 CET: flex_dsprm_forking_mixing_support:

000459: Nov 13 2013 21:06:16.109 CET: mars_flex_dsprm_current_codec_comp:DSP:0 FLEX Complexity Codec

000460: Nov 13 2013 21:06:22.412 CET: ISDN BR0/0/0 Q931: TX -> DISCONNECT pd = 8  callref = 0x18

    Cause i = 0x8090 - Normal call clearing

000461: Nov 13 2013 21:06:22.492 CET: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8  callref = 0x01

    Cause i = 0x8090 - Normal call clearing

000462: Nov 13 2013 21:06:22.516 CET: ISDN BR0/0/0 Q931: RX <- RELEASE pd = 8  callref = 0x98

000463: Nov 13 2013 21:06:22.520 CET: ISDN BR0/0/0 Q931: TX -> RELEASE_COMP pd = 8  callref = 0x18

000464: Nov 13 2013 21:06:22.524 CET: flex_dsprm_close_cleanup

Actions

This Discussion