cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
253
Views
0
Helpful
1
Replies

Frame Relay Lab Problem

nicholas dentry
Level 1
Level 1

I am using all Vwic-2mft's. I have the voice t1's making calls between sites using the PSTN. I am having an issue with getting frame relay up. I have matched the configuration from configs found on the web, and done my frame relay research. I am getting green link lights on all my frame relay interfaces but showing down, down. I cannot ping the local frame relay sub interface from the local router BTW. I am using the same pinout for both my t1 rj-45's, as well as my Frame relay rj-45's as well. Below is the configuration from my PSTN, and R3 routers.


PSTN:

interface Serial0/0/0:23

description ***Voice to R1***

no ip address

encapsulation hdlc

isdn switch-type primary-ni

isdn protocol-emulate network

isdn incoming-voice voice

no cdp enable

!

interface Serial0/0/1:0

description ***Data to R1***

no ip address

encapsulation frame-relay IETF

frame-relay lmi-type ansi

frame-relay intf-type dce

!

interface Serial0/1/0:23

description ***Voice to R2***

no ip address

encapsulation hdlc

isdn switch-type primary-ni

isdn protocol-emulate network

isdn incoming-voice voice

no cdp enable

!

interface Serial0/1/1:0

description ***Data to R2***

no ip address

encapsulation frame-relay IETF

frame-relay lmi-type ansi

frame-relay intf-type dce

!

interface Serial0/2/0:15

description ***Voice to R3***

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn protocol-emulate network

isdn incoming-voice voice

no cdp enable

!

interface Serial0/2/1:0

description ***Data to R3***

no ip address

encapsulation frame-relay IETF

frame-relay lmi-type ansi

frame-relay intf-type dce



interface Serial0/1/1:0

description frame-relay link to R2

no ip address

encapsulation frame-relay

no fair-queue

clock rate 128000

frame-relay lmi-type cisco

frame-relay intf-type dce

frame-relay route 301 interface Serial0/0/1 103

!

interface Serial0/0/1:0

description frame-relay to R1

no ip address

encapsulation frame-relay

clock rate 128000

frame-relay lmi-type cisco

frame-relay intf-type dce

frame-relay route 102 interface Serial0/1/0 201

frame-relay route 103 interface Serial0/0/0 301

!

interface Serial0/2/1:0

description frame-relay link to R3

no ip address

encapsulation frame-relay

clock rate 128000

frame-relay lmi-type cisco

frame-relay intf-type dce

frame-relay route 201 interface Serial0/0/1 102


R3:


interface Serial0/1/0:15

description ***Voice to PSTN***

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

no cdp enable

!

interface Serial0/1/1:0

description ***Data to PSTN***

no ip address

encapsulation frame-relay IETF

frame-relay lmi-type ansi



interface Serial0/1/1:0 201 point-to-point

description frame relay to R1

ip address 177.0.201.2 255.255.255.252

ip ospf network point-to-point

snmp trap link-status

frame-relay interface-dlci 201

1 Reply 1

nicholas dentry
Level 1
Level 1

I forgot to mentions I am using the CCIE v3.0 lab topology. The PSTN has 3 vwic-2mft cards, 3 ports acting as voice t1's, and the other three acting as frame relay.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: