11-13-2013 05:00 PM - edited 03-16-2019 08:23 PM
I am using all Vwic-2mft's. I have the voice t1's making calls between sites using the PSTN. I am having an issue with getting frame relay up. I have matched the configuration from configs found on the web, and done my frame relay research. I am getting green link lights on all my frame relay interfaces but showing down, down. I cannot ping the local frame relay sub interface from the local router BTW. I am using the same pinout for both my t1 rj-45's, as well as my Frame relay rj-45's as well. Below is the configuration from my PSTN, and R3 routers.
PSTN:
interface Serial0/0/0:23
description ***Voice to R1***
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
!
interface Serial0/0/1:0
description ***Data to R1***
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
frame-relay intf-type dce
!
interface Serial0/1/0:23
description ***Voice to R2***
no ip address
encapsulation hdlc
isdn switch-type primary-ni
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
!
interface Serial0/1/1:0
description ***Data to R2***
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
frame-relay intf-type dce
!
interface Serial0/2/0:15
description ***Voice to R3***
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
!
interface Serial0/2/1:0
description ***Data to R3***
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
frame-relay intf-type dce
interface Serial0/1/1:0
description frame-relay link to R2
no ip address
encapsulation frame-relay
no fair-queue
clock rate 128000
frame-relay lmi-type cisco
frame-relay intf-type dce
frame-relay route 301 interface Serial0/0/1 103
!
interface Serial0/0/1:0
description frame-relay to R1
no ip address
encapsulation frame-relay
clock rate 128000
frame-relay lmi-type cisco
frame-relay intf-type dce
frame-relay route 102 interface Serial0/1/0 201
frame-relay route 103 interface Serial0/0/0 301
!
interface Serial0/2/1:0
description frame-relay link to R3
no ip address
encapsulation frame-relay
clock rate 128000
frame-relay lmi-type cisco
frame-relay intf-type dce
frame-relay route 201 interface Serial0/0/1 102
R3:
interface Serial0/1/0:15
description ***Voice to PSTN***
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
!
interface Serial0/1/1:0
description ***Data to PSTN***
no ip address
encapsulation frame-relay IETF
frame-relay lmi-type ansi
interface Serial0/1/1:0 201 point-to-point
description frame relay to R1
ip address 177.0.201.2 255.255.255.252
ip ospf network point-to-point
snmp trap link-status
frame-relay interface-dlci 201
11-13-2013 05:02 PM
I forgot to mentions I am using the CCIE v3.0 lab topology. The PSTN has 3 vwic-2mft cards, 3 ports acting as voice t1's, and the other three acting as frame relay.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: