×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

VSOM 6.3.3 Drive Rebuild

Answered Question
Jan 10th, 2014
User Badges:

Hello all!

I was wondering if someone can post the commands to check a drive rebuild status for VSOM 6.3.3. I can see it via the WebIOS but need to check remotely. This is on an MSP series server running Linux.


Thanks

Correct Answer by Scott Olsen about 3 years 7 months ago

/opt/MegaRAID/MegaCli/MegaCli -pdrbld -showprog -physdrv "[:]" -a0


... likely.


Others are:



Info on the raid (assuming the raid is a0)


/opt/MegaRAID/MegaCli/MegaCli -ldinfo -lall -a0


/opt/MegaRAID/MegaCli/MegaCli -pdlist -a0


The file MegaSAS.log from the current directory will also contain the output of the commands,



To start the rebuild of drive 0, run the command (only if it didn't start on its own), this makes the drive a hot spare:


/opt/MegaRAID/MegaCli/MegaCli -pdrbld -start -physdrv "[:]" -a0


If a drive gets marked as "foreign", clear the foreign configuration:


/opt/MegaRAID/MegaCli/MegaCli -CfgForeign -Clear -a0


And, to silence the beeping:

/opt/MegaRAID/MegaCli/MegaCli -adpsetprop AlarmSilence -aALL



Flash start / stop

/opt/MegaRAID/MegaCli/MegaCli -pdlocate start physdrv [8:1] -a0 -nolog

/opt/MegaRAID/MegaCli/MegaCli -pdlocate stop physdrv [8:1] -a0 -nolog


Hope this helps!!



Scott Olsen
Solutions Specialist
Bulletproof Solutions Inc.
Web: www.bulletproofsi.com


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
Scott Olsen Fri, 01/10/2014 - 12:37
User Badges:
  • Silver, 250 points or more

/opt/MegaRAID/MegaCli/MegaCli -pdrbld -showprog -physdrv "[:]" -a0


... likely.


Others are:



Info on the raid (assuming the raid is a0)


/opt/MegaRAID/MegaCli/MegaCli -ldinfo -lall -a0


/opt/MegaRAID/MegaCli/MegaCli -pdlist -a0


The file MegaSAS.log from the current directory will also contain the output of the commands,



To start the rebuild of drive 0, run the command (only if it didn't start on its own), this makes the drive a hot spare:


/opt/MegaRAID/MegaCli/MegaCli -pdrbld -start -physdrv "[:]" -a0


If a drive gets marked as "foreign", clear the foreign configuration:


/opt/MegaRAID/MegaCli/MegaCli -CfgForeign -Clear -a0


And, to silence the beeping:

/opt/MegaRAID/MegaCli/MegaCli -adpsetprop AlarmSilence -aALL



Flash start / stop

/opt/MegaRAID/MegaCli/MegaCli -pdlocate start physdrv [8:1] -a0 -nolog

/opt/MegaRAID/MegaCli/MegaCli -pdlocate stop physdrv [8:1] -a0 -nolog


Hope this helps!!



Scott Olsen
Solutions Specialist
Bulletproof Solutions Inc.
Web: www.bulletproofsi.com


Actions

This Discussion

Related Content