02-11-2014 01:12 AM
we have inserted pvdm3 module in to the 2901 router
but its LED status is showing Amber continuolsly.
I would like configure the VIC3-2FXS/DID card but I am not able to see the card in running configuration but I could see the card in sh diag.
Can any ony help?
Its sh diag command giving the following output.
/#sh diag
Slot 0:
C2901 Mother board 2GE, integrated VPN and 4W Port adapter, 4 ports
Port adapter is analyzed
Port adapter insertion time 00:58:11 ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC16310CSA
Hardware Revision : 1.0
Part Number : 73-11834-09
Top Assy. Part Number : 800-30795-05
Board Revision : A0
Deviation Number : 0
Fab Version : 03
Product (FRU) Number : CISCO2901/K9
Version Identifier : V05
CLEI Code : CMMHB10ARA
Processor type : C1
Chassis Serial Number : FGL16312126
Chassis MAC Address : 6073.5c26.7440
MAC Address block size : 72
Manufacturing Test Data : 00 00 00 00 00 00 00 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 36 33 31 30 43 53 41 40
0x10: 06 17 41 01 00 82 49 2E 3A 09 C0 46 03 20 00 78
0x20: 4B 05 42 41 30 88 00 00 00 00 02 03 CB 8C 43 49
0x30: 53 43 4F 32 39 30 31 2F 4B 39 89 56 30 35 20 D9
0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 48 42 31 30 41 52
0x50: 41 09 C1 C2 8B 46 47 4C 31 36 33 31 32 31 32 36
0x60: C3 06 60 73 5C 26 74 40 43 00 48 C4 08 00 00 00
0x70: 00 00 00 00 00 F3 00 65 40 01 25 41 00 87 42 00
0x80: 00 F8 00 28 03 E8 1C 89 07 D0 20 21 0B B8 20 93
0x90: 0F A0 21 2F 13 88 21 83 17 70 21 A8 1B 58 21 B0
0xA0: 1F 40 21 AB 23 28 21 79 27 10 21 78 41 01 1D 42
0xB0: 00 00 F8 00 28 03 E8 1C 20 07 D0 1F 40 0B B8 20
0xC0: 6C 0F A0 21 34 13 88 21 34 17 70 21 98 1B 58 21
0xD0: 98 1F 40 21 98 23 28 21 34 27 10 21 34 FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
PVDM Slot 1:
16-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
Hardware Revision : 1.0
Part Number : 73-11576-03
Board Revision : C0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC162257KD
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM3-16
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 D8 41 01 00 82 49 2D 38 03 42 43 30
0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 36 32 32
0x20: 35 37 4B 44 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 8F 50 56 44 4D 33 2D 31 36 20 20 20 20 20 20 20
0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
3rd generation - FXS DID Voice daughter card (2 port)
Hardware Revision : 1.0
Top Assy. Part Number : 800-30501-02
Board Revision : A0
Deviation Number : 0
Fab Version : 07
PCB Serial Number : FOC1350420M
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VIC3-2FXS/DID
Version Identifier : V02
CLEI Code : IP9IAB3CAB
Longitudinal Calibration : 01 10 10 4F 8D 10 10 8F
9F
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 06 21 41 01 00 C0 46 03 20 00 77 25 02
0x10: 42 41 30 88 00 00 00 00 02 07 C1 8B 46 4F 43 31
0x20: 33 35 30 34 32 30 4D 03 00 81 00 00 00 00 04 00
0x30: CB 8D 56 49 43 33 2D 32 46 58 53 2F 44 49 44 89
0x40: 56 30 32 20 D9 02 40 C1 C6 8A 49 50 39 49 41 42
0x50: 33 43 41 42 D3 09 01 10 10 4F 8D 10 10 8F 9F FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Embedded Service Engine 0/0 :
Total platform memory : 524288K bytes
Total 2nd core memory : 0K bytes
Start of physical address for 2nd core : 0x80000000
Virtual address start of 2nd core memory : 0x0 - 0x0
2nd core configured disabled
L2 cache ways for 2nd core : 0
Its sh running-conf command giving the following output.
/#sh running-config
Building configuration...
Current configuration : 1228 bytes
!
! Last configuration change at 06:29:29 UTC Fri Feb 7 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname /
!
boot-start-marker
boot-end-marker
!
!
enable secret 4 tnhtc92DXBhelxjYk8LWJrPV36S2i4ntXrpb4RFmfqY
!
no aaa new-model
!
no ipv6 cef
ip source-route
ip cef
!
!
!
!
!
multilink bundle-name authenticated
!
!
crypto pki token default removal timeout 0
!
!
license udi pid CISCO2901/K9 sn FGL16312126
hw-module pvdm 0/1
!
!
!
username cisco
!
!
!
!
!
!
interface Embedded-Service-Engine0/0
no ip address
no ip route-cache
shutdown
!
interface GigabitEthernet0/0
ip address 172.169.2.152 255.255.255.0
duplex auto
speed auto
!
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
!
!
!
!
control-plane
!
!
!
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password cisco
login
transport input all
line vty 5 15
password cisco
login
transport input all
!
scheduler allocate 20000 1000
end
and sh flash giving me the following output.
/#sh flash
-#- --length-- -----date/time------ path
1 74503236 Jul 30 2012 20:08:54 +00:00 c2900-universalk9-mz.SPA.151-4.M4.bin
2 2903 Jul 30 2012 20:21:54 +00:00 cpconfig-29xx.cfg
3 3000320 Jul 30 2012 20:22:10 +00:00 cpexpress.tar
4 1038 Jul 30 2012 20:22:18 +00:00 home.shtml
5 122880 Jul 30 2012 20:22:26 +00:00 home.tar
6 1697952 Jul 30 2012 20:22:40 +00:00 securedesktop-ios-3.1.1.45-k9.pkg
7 415956 Jul 30 2012 20:22:54 +00:00 sslclient-win-1.1.4.176.pkg
02-11-2014 01:28 PM
Duplicate posts.
02-19-2014 09:58 PM
Attach show version.
Regards,
Kevin
Sent from Cisco Technical Support Android App
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: