05-23-2014 01:09 PM - edited 03-04-2019 11:01 PM
Would like your assistance please regarding below quesitos
1- As you know to verify multicast we can use ping.
My problem is that when you ping using source loopback address it does not work [spare-mode is configured normally under loopback] however when you configure using outgoing interface it pings normally
What could be the reason for this ?
2- Does XRv simulator works fine with multicast. I am having very strange behavior is that OIL list is always null although source is directly connected. Not sure if its a bug or XRv issue
R8#ping 227.7.7.7 repeat 10
Type escape sequence to abort.
Sending 10, 100-byte ICMP Echos to 227.7.7.7, timeout is 2 seconds:
..........
R8#
RP/0/0/CPU0:XR2#show pim topology
Thu May 22 06:14:34.625 UTC
IP PIM Multicast Topology Table
Entry state: (*/S,G)[RPT/SPT] Protocol Uptime Info
Entry flags: KAT - Keep Alive Timer, AA - Assume Alive, PA - Probe Alive
RA - Really Alive, IA - Inherit Alive, LH - Last Hop
DSS - Don't Signal Sources, RR - Register Received
SR - Sending Registers, SNR - Sending Null Registers
E - MSDP External, EX - Extranet
MFA - Mofrr Active, MFP - Mofrr Primary, MFB - Mofrr Backup
DCC - Don't Check Connected, ME - MDT Encap, MD - MDT Decap
MT - Crossed Data MDT threshold, MA - Data MDT Assigned
SAJ - BGP Source Active Joined, SAR - BGP Source Active Received,
SAS - BGP Source Active Sent, IM - Inband mLDP
Interface state: Name, Uptime, Fwd, Info
Interface flags: LI - Local Interest, LD - Local Dissinterest,
II - Internal Interest, ID - Internal Dissinterest,
LH - Last Hop, AS - Assert, AB - Admin Boundary, EX - Extranet,
BGP - BGP C-Multicast Join, BP - BGP Source Active Prune,
MVS - MVPN Safi Learned, MV6S - MVPN IPv6 Safi Learned
(*,224.0.1.40) DM Up: 00:56:21 RP: 0.0.0.0
JP: Null(never) RPF: Null,0.0.0.0 Flags: LH DSS
Loopback0 00:56:21 off LI II LH
GigabitEthernet0/0/0/2 00:56:14 off LI LH
(*,227.7.7.7) SM Up: 00:29:15 RP: 20.20.20.20*
JP: Join(never) RPF: Decapstunnel3,20.20.20.20 Flags:
GigabitEthernet0/0/0/2 00:29:15 fwd Join(00:03:13) <<--- receiver sends PIM Join normally
(10.8.20.8,227.7.7.7)SPT SM Up: 00:00:03
JP: Join(00:00:46) RPF: GigabitEthernet0/0/0/0.820,10.8.20.8* Flags: KAT(00:03:29) RA RR (00:04:33)
No interfaces in immediate olist <<<<<------
Appreciate your assistance
Regards
Sherif Ismail
07-16-2014 11:39 PM
Hi Sherif Ismail,
I encountered this and checked around. It seems that XRv supports Control-Plane features fully - BGP/IGP/LDP/PIM/etc. will work. However, Data-plane is supported with limitations.
Cheers,
Cuong.
09-12-2014 08:52 AM
Hello,
I just installed XRv 5.2.0. Shall I expect MVPN data plane work?
Thanks,
Ato
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: