Solved: redundant supervisor in Stanby Cold state

Mike Mott · ‎06-12-2014

We had a Sup 2T throw a parity error, TAC RMA'd a replacement SUP2T. I ensured that the same IOS version was on the replacement. Inserted the card and in Show Mod it shows pass and ok however when I look at the show redundancy I am seeing the replacement SUP i as Standby COLD. when I look at the show redundancy states I see the following:

Redundancy Mode (Operational) = rpr Reason: Software mismat

when I look at the Bootvar I see the following:

BOOT variable = bootdisk:s2t54-advipservicesk9-mz.SPA.151-1.SY1.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102

Standby BOOT variable = bootdisk:s2t54-advipservicesk9-mz.SPA.151-1.SY1.bin,1;
Standby CONFIG_FILE variable =
Standby BOOTLDR variable =
Standby Configuration register is 0x2102

Any Ideas ?

Marvin Rhoads · ‎06-12-2014

That all looks good. I notice your operational redundancy mode is RPR. Is that the configured mode (normally SSO would be the configured mode).

Does "show module" recognize the replaced card properly? Have you tried reloading the standby supervisor ("redundancy reload peer")? I'd do that while checking if any console or syslog messages are generated during that process to give more troubleshooting clues.

View solution in original post

Marvin Rhoads · ‎06-12-2014

Do you perhaps have licensing (e.g., MacSEC) on the primary that isn't matched on the secondary?

"show license all"

"show license feature"

Mike Mott · ‎06-12-2014

Here is the output from these two commands

show license all
License Store: Primary License Storage
License Store: Evaluation License Storage
StoreIndex: 0 Feature: TEST_FEATURE_1 Version: 1.0
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
Evaluation total period: 4 weeks 2 days
Evaluation period left: 4 weeks 2 days
Lock type: Non Node locked
Vendor info:
License Addition: Additive
License Generation version: 0x8100000
License Count: Non-Counted
License Priority: None
StoreIndex: 1 Feature: TEST_FEATURE_2 Version: 1.0
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
Evaluation total period: 1 hour 0 minute
Evaluation period left: 1 hour 0 minute
Lock type: Non Node locked
Vendor info:
License Addition: Additive
License Generation version: 0x8100000
License Count: Non-Counted
License Priority: None

show license feature
Feature name Enforcement Evaluation Subscription Enabled
MACSec_Encryption yes no no no
CTS yes no no no
TEST_FEATURE_1 yes yes no no
TEST_FEATURE_2 yes yes no no

Marvin Rhoads · ‎06-12-2014

That all looks good. I notice your operational redundancy mode is RPR. Is that the configured mode (normally SSO would be the configured mode).

Does "show module" recognize the replaced card properly? Have you tried reloading the standby supervisor ("redundancy reload peer")? I'd do that while checking if any console or syslog messages are generated during that process to give more troubleshooting clues.

pmodcnrma · ‎07-12-2019

Hi,

My name is sandeep i have understand your problem of Rsp 720 ios mismatch issue.

pls run below command

Rt-01#redundancy config-sync ignore mismatched-commands

then reload the sup card to run below command

Rt-01# redundancy reload peer

I hope issue will resolved !!!!!

pls confirm once issue will resolved!!!

Thx

Sandeep