×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Cisco Aironet AIR-LAP1142N-E-K9

Unanswered Question
Oct 29th, 2014
User Badges:

I am using Cisco Aironet AIR-LAP1142N-E-K9 on my network and it's connected to Gigabitethernet port on my 3750 switch, but for some eason it's neotiating only 100Mbps all time even when I run speed auto from both sides. If I run 1000Mbps from the switch and the AP, I loose connectivity. Please find below details:


-------------------------
Device ID: BTaS-RYD-5F-AP02
Entry address(es): 
  IP address: 192.168.15.252
Platform: cisco AIR-LAP1142N-E-K9   ,  Capabilities: Trans-Bridge IGMP 
Interface: GigabitEthernet1/0/14,  Port ID (outgoing port): GigabitEthernet0
Holdtime : 138 sec

Version :
Cisco IOS Software, C1140 Software (C1140-K9W7-M), Version 12.4(21a)JA1, RELEASE SOFTWARE (fc1)

 

Output from the switch interface:


Port          Name                        Status          Vlan       Duplex     Speed    Type
Gi1/0/14  ***BTAS-7flr-AP03*   connected    trunk        full          a-100     10/100/1000BaseTX

 

Yasir

 

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Leo Laohoo Wed, 10/29/2014 - 14:55
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    The Hall of Fame designation is a lifetime achievement award based on significant overall achievements in the community. 

  • Cisco Designated VIP,

    2017 LAN, Wireless

Run a TDR on your switch.   I am suspecting you've got a faulty cable.  

 

Do the following commands: 

 

1.  Command:  test cable tdr interface Gi1/0/14; 

2.  Wait for approximately 5 to 7 seconds to run the test; 

3.  Command:  sh cable tdr interface Gi1/0/14; and 

4.  Post the output to #3.

yasir.elmusharaf Thu, 10/30/2014 - 06:21
User Badges:

Please find below:

 

BTaS-7F-SW-2#test cable-diagnostics tdr interface gi

 

BTaS-7F-SW-2#test cable-diagnostics tdr interface gigabitEthernet 1/0/14

 

Link state may be affected during TDR test

 

TDR test started on interface Gi1/0/14

 

A TDR test can take a few seconds to run on an interface

 

Use 'show cable-diagnostics tdr' to read the TDR results.

 

BTaS-7F-SW-2#

 

BTaS-7F-SW-2#

 

BTaS-7F-SW-2#

 

BTaS-7F-SW-2#show cable-diagnostics tdr ?

 

  interface  Specify an interface for result

 

 

 

BTaS-7F-SW-2#show cable-diagnostics tdr int gi

 

BTaS-7F-SW-2#show cable-diagnostics tdr int gigabitEthernet 1/0/14

 

TDR test last run on: March 10 04:38:17

 

 

 

Interface Speed Local pair Pair length        Remote pair Pair status

 

--------- ----- ---------- ------------------ ----------- --------------------

 

Gi1/0/14  100M  Pair A     N/A                N/A         Not Completed

 

                Pair B     N/A                N/A         Not Completed

 

                Pair C     N/A                N/A         Not Completed

 

                Pair D     N/A                N/A         Not Completed

 

BTaS-7F-SW-2#

 

 

 

Leo Laohoo Thu, 10/30/2014 - 20:40
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    The Hall of Fame designation is a lifetime achievement award based on significant overall achievements in the community. 

  • Cisco Designated VIP,

    2017 LAN, Wireless

Link state may be affected during TDR test

Uhhhhh ... what ancient IOS are you running????

Actions

This Discussion