×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Assign Vlan to SSID

Answered Question
Oct 30th, 2014
User Badges:

I have a few Cisco 1141n that are stand alone AP's that have one SSID on them. I would like to assign the ssid to vlan 2 but also be able to keep the native vlan 1 as a trunk port on it for snmp graphing as well as management of the ap. My router is going to route the traffic and my switch is the dhcp server for both vlan's. How would I go about putting ssid J&B2 on vlan 2 but keeping the 10.10.1.0 network (vlan 1) as the ip address for management? I'm guessing it would be something along the lines of a sub interface but I am lost on do I create the sub interface on the gigabit port or the dot11radio0 interface or both?

 

I've attached a copy of my current config. Thank you for helping me figure this out. 

Attachment: 
Correct Answer by Rasika Nayanajith about 2 years 9 months ago

Hi

I think I missed a line under int d0. Try this & see

encryption vlan 2 mode ciphers aes-ccm

 

HTH

Rasika

*** Pls rate all useful responses ****

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (2 ratings)
Loading.
Rasika Nayanajith Thu, 10/30/2014 - 19:10
User Badges:
  • Purple, 4500 points or more
  • Cisco Designated VIP,

    2017 Wireless

Hi JK,

Following config will do it for you

dot11 ssid J&B2
   vlan 2
   authentication open
   authentication key-management wpa version 2
   guest-mode
   wpa-psk ascii 7 14141D061C113E2E662F2627370054455B5817
!
interface Dot11Radio0
 encryption mode ciphers aes-ccm
 ssid J&B2
 no shut
!
interface Dot11Radio0.1
 encapsulation dot1Q 1 native
 bridge-group 1
!
interface Dot11Radio0.2
 encapsulation dot1Q 2
 bridge-group 2
!
interface GigabitEthernet0.1
 encapsulation dot1Q 1 native
 bridge-group 1
!
interface GigabitEthernet0.2
 encapsulation dot1Q 2
 bridge-group 2
!
interface BVI1
 ip address 10.10.1.252 255.255.255.0
!
ip default-gateway 10.10.1.253


******* SWITCH PORT ******

interface GigabitEthernetx/x
 switchport trunk encapsulation dot1q
 switchport trunk native vlan 1
 switchport trunk allowed vlan 1-2
 switchport mode trunk
!

Initial config used for this post will help you  as well.

http://mrncciew.com/2013/11/14/autonomous-ap-with-external-radius/

 

HTH

Rasika

**** Pls rate all useful responses ***

jkay18041 Thu, 10/30/2014 - 19:32
User Badges:

Thank you for your response. I went ahead and changed my config to the following. I am now unable to connect to my wifi network. I was able to connect before it just put me on vlan 1. I changed the settings on my switch as well.

 

Did I do something wrong on the AP config?

 

Thank you for your help

Attachment: 
Correct Answer
Rasika Nayanajith Thu, 10/30/2014 - 19:34
User Badges:
  • Purple, 4500 points or more
  • Cisco Designated VIP,

    2017 Wireless

Hi

I think I missed a line under int d0. Try this & see

encryption vlan 2 mode ciphers aes-ccm

 

HTH

Rasika

*** Pls rate all useful responses ****

jkay18041 Thu, 10/30/2014 - 19:40
User Badges:

Good eye!

 

Thank you very much for your help. After seeing how you configured it this makes sense. Thank you again. Very appreciated! 

Rasika Nayanajith Thu, 10/30/2014 - 20:25
User Badges:
  • Purple, 4500 points or more
  • Cisco Designated VIP,

    2017 Wireless

No worries, Glad I was able to help you... :)

Rasika

Actions

This Discussion