cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
771
Views
0
Helpful
4
Replies

BNG Program Problem of the ASR9010

wuyian2012
Level 1
Level 1

HI 

  I have to ASR9010 to be a NvEdge Systems.and i need get a BNG in my ASR9010

  this is my configuation

  now subscribers can creating the session by BNG,and register in the CoA(PortServer) and Radius Server

 but my account have a problem, in my show subscriber session all detail,i can see the username and COA pushed username
RP/0/RSP0/CPU0:ios#show subscriber session all detail 

Mon Apr 20 23:24:02.171 UTC
Interface:                Bundle-Ether100.2.ip12
Circuit ID:               Unknown
Remote ID:                Unknown
Type:                     IP: Packet-trigger
IPv4 State:               Up, Mon Apr 20 23:23:42 2015
IPv4 Address:             49.52.9.119, VRF: default
Mac Address:              Unknown
Account-Session Id:       0000028d
Nas-Port:                 Unknown
User name:                test1 <------------------------------there
Formatted User name:      unknown
Client User name:         unknown
Outer VLAN ID:            2
Subscriber Label:         0x00000052
Created:                  Mon Apr 20 23:23:42 2015
State:                    Activated
Authentication:           authenticated
Authorization:            unauthorized
Access-interface:         Bundle-Ether100.2
Policy Executed: 
policy-map type control subscriber IP_PM
  event Session-Start match-first [at Mon Apr 20 23:23:42 2015]
    class type control subscriber IPoE do-until-failure [Succeeded]
      5 activate dynamic-template IP_SUB [Succeeded]
      10 activate dynamic-template HTTPR [Succeeded]
      20 set-timer UNAUTH_TMR 1 [Succeeded]
  event Account-Logon match-first [at Mon Apr 20 23:23:53 2015]
    class type control subscriber IPoE do-until-failure [Succeeded]
      10 authenticate aaa list ECNU [Succeeded]
      20 deactivate dynamic-template HTTPR [Succeeded]
Session Accounting:        
  Acct-Session-Id:          0000028d
  Method-list:              ECNU
  Accounting started:       Mon Apr 20 23:23:42 2015
  Interim accounting:       On, interval 10 mins
    Last successful update: Never
    Next update in:         00:09:41 (dhms)
Last COA request: Mon Apr 20 23:23:53 2015
COA Request  Attribute List: 0x1000f0c4
1:  addr            len=  4  value= 49.52.9.119
2:  password        len=  6  value= <opaque value>
3:  username        len=  5  value= test1   <------------------------------there
4:  command         len= 14  value= account-logon
Last COA response: Result ACK
COA Response  Attribute List: 0x1000f2d4

but my radius Server can't see the username of the Session

radius Server only can see the username(mac) in the IPoE L2 session, and see null in the IPoE L3 session

what wrong of me?

thanks 

 

 

 

 

 

 

 

1 Accepted Solution

Accepted Solutions

Hi, looks like we need more to investigate here. Can you please share the image details and show platform ? Do you have all the mandatory SMU's installed ?

 

 

View solution in original post

4 Replies 4

xthuijs
Cisco Employee
Cisco Employee

it looks like you have accounting enabled on your services.

the services that were defined as subscriber templates may not have gotten notification that

the username was updated.

try this:

1) convert the templates for the services from ipsubscriber to service

or

2) alternatively, remove the accounting directives from the templates and when the user logs on, provide the subscriber:accounting directive in the coa account logon profile to start subscriber accounting.

xander

hello i'm so sorry to see the problem too late

 i am testing the BNG in the ASR9010 all of week

 1.now i config the account and a new problem occur

 when the subscriber logging on , when occur the logging

LC/0/1/CPU0:Apr 29 15:25:52.829 : prm_server_ty[314]: %PLATFORM-NP-3-DIAG : NP-DIAG failure on NP1, STS-0 = 0x00400000  MDF0-level cause 0x100  
LC/0/1/CPU0:Apr 29 15:25:52.833 : pfm_node_lc[301]: %PLATFORM-NP-2-NP_DIAG : Set|prm_server_ty[172114]|0x1008001| NP diagnostics warning on NP1. 
LC/0/1/CPU0:Apr 29 15:26:10.991 : prm_server_ty[314]: %PLATFORM-NP-4-FAULT : Fast Reset NP1 - successful auto-recovery of NP 
LC/0/1/CPU0:Apr 29 15:26:10.991 : pfm_node_lc[301]: %PLATFORM-NP-2-NP_DIAG : Clear|prm_server_ty[172114]|0x1008001| NP diagnostics warning on NP1. 
LC/0/1/CPU0:Apr 29 15:27:07.358 : prm_server_ty[314]: %PLATFORM-NP-3-DIAG : NP-DIAG failure on NP1, STS-0 = 0x00c00000  MDF0-level cause 0x800  
LC/0/1/CPU0:Apr 29 15:27:07.359 : pfm_node_lc[301]: %PLATFORM-NP-2-NP_DIAG : Set|prm_server_ty[172114]|0x1008001| NP diagnostics warning on NP1. 
LC/0/1/CPU0:Apr 29 15:27:24.595 : prm_server_ty[314]: %PLATFORM-NP-4-FAULT : Fast Reset NP1 - successful auto-recovery of NP 
LC/0/1/CPU0:Apr 29 15:27:24.595 : pfm_node_lc[301]: %PLATFORM-NP-2-NP_DIAG : Clear|prm_server_ty[172114]|0x1008001| NP diagnostics warning on NP1. 

when the three fast reset in a hour ,my MOD80 SE will all down

so i can't know why will cause it?is my config is error?

 

 

Hi, looks like we need more to investigate here. Can you please share the image details and show platform ? Do you have all the mandatory SMU's installed ?

 

 

thanks a lot

 i have a case,and the R&D give me a new SMU to resolve the ASR9010 SE shutdown

 the config i and tac will finish it

thanks

 

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: