Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1944030members
1275705discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

can't access skillsforall.com page with laptop.

Hello, i need some assistance. For the past 2 days i have been unable to login to skillsforall.com with my laptop, it just keep loading the rotating circle endlessly. Now https://skillsforall.com/ doesn't even load anymore, weird thing is it opens ju...

Cisco FMC Deployment using API

Hello Folks,Hope you are doing well.I am new to to the security and tring to setup a LAB with FTD and FMC.I just configured an interface of FTD from FMC but while deploying that getting error related to CPU and now trying to do it from CLI using API....

FMC ACP Rule Filter with "Any" default parameter

Is there a way to search or filter an ACP on the FMC for rules that has the default "Any" value parameter?The search rules option is the closest but what search parameter to put (ie. on source or destination networks) if I want see the policies that ...

Subnetting

The acquired building consists of a reception department and an administration + management department. After consulting with the team, designed the following layout. After some minor adjustments, our our technical department to install the hardware ...

1pgordo by • Level 1
  • 12 Views
  • 1 replies
  • 0 Helpful votes

Strange ASR-1001 Access-lists behavior

Hello,I am trying to implement control plane policies on my test equipment, my cto is asking me to limit the ICMP max rate for all untrusted addresses. (I have to create an exception for knows hosts)Having very little experience in CoPP, I believed t...

RemsoO by • Level 1
  • 10 Views
  • 0 replies
  • 1 Helpful votes

IP ROUTING

Hello guys, below is my topology,I have added internet fw  and introduced ISP on site B.Before site B resources/ servers would go via mpls to site a to access internet.I introduced the above to make each site use its own isp respectively.I ran to cha...

fmugambi_0-1716902477086.png
fmugambi by • Spotlight
  • 126 Views
  • 6 replies
  • 0 Helpful votes

Correct answer marked as wrong

I have identified at least 2 quiz questions that identify correct answer as incorrect:12.3.3 Gateways to Other Networks QuizQuestion 5If the default gateway is configured incorrectly on a host, what is the impact on communications? 1. The host is una...

BGP Advertisement

Hello,I need some help with the following BGP configuration router bgp 300neighbor 192.169.10.1 remote-as 200neighbor 192.169.10.1 description ISP-Aneighbor 192.169.20.1 remote-as 400neighbor 192.169.20.1 description ISP-B!address-family ipv4network ...

Norman123 by • Level 1
  • 175 Views
  • 6 replies
  • 0 Helpful votes

FTD 2130 Performace optimization using fastpath

Hello, A customer are having some issues with performances when the CPU of there FTD 2130 sometimes reach 90% and start dropping traffic due to occasionally high amount of traffic. This is mostly internal traffic within a Kubernetes cluster.  If we w...

Capture.JPG

Resolved! Import Translation Pattern Fails

Good night for all.I'm trying to import a translation pattern csv file (previously exported) and it doesn't work.When I verify the file, I seems to be ok but when I try to import it, appears a message in the log file that indicates "translation patte...

APIC interfaces question

On APIC-M2 where I have 2 phy fabric connections but at the GUI I have seen 4 phy interfaces, can someone help to explain the relationship or mapping between them. I am going to replace the APIC-M2 with APIC-M4 soon and need to move all the phy conne...

a12288_0-1716928237292.png
a12288 by • Level 3
  • 70 Views
  • 2 replies
  • 0 Helpful votes
Load more