04-21-2016 11:44 AM - edited 03-18-2019 11:57 AM
Hello all ,
I am trying to add MGCP gateway to CUCM , I follow all the configuration as in the attached files and It appears to be unregistered on CUCM.
I am using CUCM 11.x , Cisco Router 2921
Solved! Go to Solution.
04-21-2016 12:57 PM
And do you have a live circuit connected to that port??
Or you just configured it??
Assuming all the configuration is fine, if there's no live circuit, it will NEVER register.
04-21-2016 06:18 PM
Do you have a PRI cable plugged into that port??
04-21-2016 12:10 PM
You need add below things depending upon T1 or E1 line code and framing,switchtype will vary
1) Card type-
card type t1/E1 {Slot}
2) Controller config
controller T1
cablelength long 0db
framing esf*
linecode b8zs*
pri-group timeslots 1-24 service mgcp
description PRI
3) Bind serial interface to CCM.
Interface serial0/1/0:23
isdn switch-type primary-4ess
isdn incoming-voice voice
isdn bind-13 ccm-manager>>>>>>>>>>>>>>>>>Very imp
Also add network clock command
network-clock-participate wic X
network-clock-select 1 T1 X/X/X
* means only for T1
04-21-2016 04:26 PM
I will follow the following and keep you updated also , Thanks for helping me in all topics.
Short question here :
when I try to show the controller the command didn't work.
04-21-2016 05:51 PM
Please make sure PRI is physically plugged into your MGCP gateway as advised by Jaime .
Also enable the card type and then you should be able to see the controller . You need to use command to configure depending upon whether you have E1 or T1 circuit.
"Controller T1/E1 X/X/X"
Also don't forget to rate helpful posts.
Regards
Deepak Mehta
04-22-2016 12:47 AM
Hi,
from the attachment , u can see u need to add card type command .
version 15.5
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname VG-MHI
!
boot-start-marker
boot-end-marker
!
!
! card type command needed for slot/vwic-slot 0/0
I suppose u are using BE6000S [2921 router] since I can see interface ucse .
After u enable card type in router and enter the required configuration as suggested by Deepak[+5] , u can physically shot the 1,4 and 2,5 pins of RJ-45 cable on open side of E1 cable and check on CUCM for MGCP registration as UP.
regds,
aman
04-23-2016 01:43 AM
Yes it is BE6S 2921 but I use it only as a VG , I will Plug it today with the teleco and update you all back , Thanks all for Helping
04-24-2016 06:22 AM
Please refer the link
https://supportforums.cisco.com/discussion/12476251/mgcp-not-registering-call-manager-105-router-2921-e1-configuration#comment-10426246
configure framing no-crc4 under controller E1.
also, what is status of show controller e1 and show isdn status on router?
regds,
aman
04-24-2016 10:24 AM
controller conf attached and ISDN status show that layer 1 is shut down , i think it is cable problem or a problem from teleco side
Global ISDN Switchtype = primary-4ess
%Q.931 is backhauled to CCM MANAGER 0x0003 on DSL 0. Layer 3 output may not apply
ISDN Serial0/0/0:15 interface
dsl 0, interface ISDN Switchtype = primary-net5
L2 Protocol = Q.921 0x0000 L3 Protocol(s) = CCM MANAGER 0x0003
Layer 1 Status:
SHUTDOWN
Layer 2 Status:
TEI = 0, Ces = 1, SAPI = 0, State = TEI_ASSIGNED
Layer 3 Status:
0 Active Layer 3 Call(s)
Active dsl 0 CCBs = 0
The Free Channel Mask: 0x00000000
Number of L2 Discards = 0, L2 Session ID = 0
Total Allocated ISDN CCBs = 0
04-24-2016 10:34 AM
To confirm, if it is really a cable or configuration issue at Telco side, try taking RJ-45 to un- terminated [open] cable and shot TX-RX pairs.
It should be error free.
regds,
aman
04-24-2016 05:46 AM
I configure it as an E1 as mention in a reply to Jamie and it looks fine on the 2921 but on cucm still unregistred !
04-25-2016 05:33 AM
Hello ,
This command did not work isdn bind-13 ccm-manager only this is available : isdn bind-l3 q931
04-21-2016 12:57 PM
And do you have a live circuit connected to that port??
Or you just configured it??
Assuming all the configuration is fine, if there's no live circuit, it will NEVER register.
04-21-2016 04:23 PM
Hello Jamie ,
Sorry I don't know what do you mean by live circuit.
04-21-2016 06:18 PM
Do you have a PRI cable plugged into that port??
04-22-2016 09:33 AM
No it still not connected the teleco provider switch , I thought it will be registered normali like the fxs config.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: