Here is the boot text..anything else needed?
Boot from flash
IOS Bootloader - Starting system.
FLASH CHIP: Spansion S25FL256
Xmodem file system is available.
flashfs[0]: 11 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 5918208
flashfs[0]: Bytes available: 26017792
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: e8:65:49:21:06:f0
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...##############
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entry point: 0x2004000
executing...
Secondary Bootloader - Starting system.
FLASH CHIP: Spansion S25FL256
Xmodem file system is available.
flashfs[0]: 11 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 5918208
flashfs[0]: Bytes available: 26017792
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: e8:65:49:21:06:f0
Secondary bootloader Ethernet not enabled, skip ether_init
Boot CMD: 'boot flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx;flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx'
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx"...#######################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-xx" uncompressed and installed, entry point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.3(3)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Thu 19-Feb-15 09:33 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Spansion S25FL256
flashfs[2]: 11 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 5918208
flashfs[2]: Bytes available: 25889792
flashfs[2]: flashfs fsck took 10 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 0 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
cisco AIR-CAP1602I-A-K9 (PowerPC) processor (revision B0) with 187382K/74672K bytes of memory.
Processor board ID FCW1929N2RT
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.115.0
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: E8:65:49:21:06:F0
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC192898H9
Top Assembly Part Number : 800-102028-03
Top Assembly Serial Number : FCW1929N2RT
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-A-K9
% Please define a domain-name first.
ipv6 enable
^
% Invalid input detected at '^' marker.
ipv6 address autoconfig
^
% Invalid input detected at '^' marker.
ipv6 address dhcp
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.683: APAVC: Initial WLAN Buffers Given to System is 500
*Mar 1 00:00:12.699: APAVC: WlanPAKs 9355 RadioPaks 8747
*Mar 1 00:00:13.343: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:14.723: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:15.639: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.3(3)JA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2015 by Cisco Systems, Inc.
Compiled Thu 19-Feb-15 09:33 by prod_rel_team
*Mar 1 00:00:15.675: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
*Mar 1 00:00:16.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:18.215: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully
APe865.4921.06f0>
*Mar 1 00:00:27.655: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:28.655: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:00:34.383: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg
%Error opening flash:/capwap-saved-config (No such file or directory)
