cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2089
Views
0
Helpful
4
Replies

IR829 Stuck in rommon -2

John.Barbour
Level 1
Level 1

I have a IR829 that is stuck in rommon -2

When I try to boot flash:ir800-universalk9-mz.SPA.156-3.M I get the following reading.

rommon-2> boot flash:ir800-universalk9-mz.SPA.156-3.M
Booting image: flash:ir800-universalk9-mz.SPA.156-3.M.... [Multiboot-elf, <0x
110000:0x9d764bc:0x4a85f8>, shtab=0xa32f2f8[csvds]:/ir800-universalk9-mz.SPA.15
6-3.M... , entry=0x1100b0]
[CU:0]
Jumps to: 0x1100b0
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
Onboard devices &
buffer pools 0x03644000
-----------------------------------------------
TOTAL: 0x03644000
Rounded IOMEM up to: 55MB.
Using 12 percent iomem. [55MB/448MB]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, ir800 Software (ir800-UNIVERSALK9-M), Version 15.6(3)M, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Thu 28-Jul-16 04:10 by prod_rel_team
<3> [691.241976] IOAPIC: IOAPIC 1 initialized, implementation version 32
<3> [691.241976] <E1000> e1000_device_init: initialized E1000 device
<3> [691.241976] <E1000> e1000_device_init: initialized E1000 device
<6> PCI: Initializing
<6> PCI: Resetting devices
<6> PCI: Resetting device QAT15 (00:0b.0)
<6> PCI: Resetting device SMBUS1 (00:13.0)
<6> PCI: Resetting device ETH0 (00:14.0)
<6> PCI: Resetting device ETH1 (00:14.1)
<6> PCI: Resetting device ETH2 (00:14.2)
<6> PCI: Resetting device ETH3 (00:14.3)
<6> PCI: Finished resetting devices
<6> PCI: Restoring devices
<6> PCI: Finished Initializing
IOS image signature verification was: FAILURE
Autoboot string flash:ir800-universalk9-mz.SPA.156-3.M,12;
Failed to boot, skip first flash:ir800-universalk9-mz.SPA.156-3.M,12;
Are their any options or is this an RMA.
Thanks,
John 
4 Replies 4

Leo Laohoo
Hall of Fame
Hall of Fame
IOS image signature verification was: FAILURE
Autoboot string flash:ir800-universalk9-mz.SPA.156-3.M,12;
IOS is corrupt.  Download the IOS again from the Cisco website.

Thank you Leo.

That is what I was thinking, but I wanted to make sure. I did see on Cisco.com that the 829 has this issue and may have to be a RMA. I will give this a try.

"IOS image signature verification was: FAILURE"? Two reasons:

1. The IOS is corrupt; and
2. An IOS bug.

Try to load with other IOS 

Is there any other IOS available in flash?

15.6 version is the new stuff i would recommend to use 15.5.

Spooster IT Services Team

rommon-2> dir
flash:
MC7354_1102037_9903214_05.05.58.00_00_ATT_005.009_000
ir800-universalk9-mz.SPA.156-3.M
MC735X_9999999_9902574_05.05.58.00_00_GENNA_005.025_000
managed
eem
rommon-2>
this is what is showing in the directory. 
The pickle is that this is a loaner from cisco for us to testing, and I cannot get the IOS from cisco.com because we have not officially purchased these yet. 
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: