×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

how do you upgrade a 4700 from the bootstrap?

Unanswered Question
Jun 27th, 2002
User Badges:
  • Bronze, 100 points or more

I tried upgrading our 4700 router, and it all seemed to be fine until I rebooted, I get the following errors when I reload:


System Bootstrap, Version 5.2(7) [rchiao 7], RELEASE SOFTWARE (fc1)

Copyright (c) 1994 by cisco Systems, Inc.

C4500 processor with 32768 Kbytes of main memory


program load complete, entrypt: 0x80008000, size: 0x37f768


Error : compressed image checksum is incorrect 0x2DE67334

Expected a checksum of 0x98EFD3B9


___ System received a Software forced crash ___

signal= #17, code= #5, context= #0

PC = 0x80008094, Cause = 0x20, Status Reg = 0x30408403


System Bootstrap, Version 5.2(7) [rchiao 7], RELEASE SOFTWARE (fc1)

Copyright (c) 1994 by cisco Systems, Inc.

C4500 processor with 32768 Kbytes of main memory


loadprog: error - on read during ELF program load

requested 3648744 (0x37ace8) bytes, got 3503143 (0x357427)

boot: cannot load "flash:"


System Bootstrap, Version 5.2(7) [rchiao 7], RELEASE SOFTWARE (fc1)

Copyright (c) 1994 by cisco Systems, Inc.

C4500 processor with 32768 Kbytes of main memory


program load complete, entrypt: 0x80008000, size: 0x248b30


Restricted Rights Legend


Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.


cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706




Cisco Internetwork Operating System Software

IOS (tm) 4500 Bootstrap Software (C4500-XBOOT), Version 10.2(7), RELEASE SOFTWARE (fc1)

Copyright (c) 1986-1995 by cisco Systems, Inc.

Compiled Thu 06-Jul-95 00:18 by rchiao

Image text-base: 0x60008780, data-base: 0x601D0000


cisco 4700 (R4K) processor (revision B) with 32768K/4096K bytes of memory.

Processor board serial number 02479837

R4700 processor, Implementation 32, Revision 2.0 (Level 2 Cache)

G.703/E1 software, Version 1.0.

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.

2 Serial network interfaces.

128K bytes of non-volatile configuration memory.

4096K bytes of processor board System flash (Read/Write)

4096K bytes of processor board Boot flash (Read/Write)


Press RETURN to get started!


Router(boot)>



I can't find a way to load a new image from here, or from the rommon, I've booted into the rommon and don't get an xmodem command. I'm at a loss as to how to do anything, does anyone have any ideas? Thanks


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Anonymous (not verified) Thu, 06/27/2002 - 14:13
User Badges:

From the Router(boot)> prompt, you

should be able to go into enable mode

and "copy tftp flash" the image

again.


Actions

This Discussion