call not end to end ISDN

Unanswered Question

we have a remote isdn site (804) that suddenly cannot connect to our receiving 3640. local telco and long distance providers have "tested" and ruled themselves out. other remote sites are fine. i can get them to connect with the 1010220 prefix. Does anyone know any buzz words that i can use to get the telco to own up to their problem..


Mar 12 12:52:15 EST: BR0 DDR: rotor dialout [priority]

Mar 12 12:52:15 EST: BR0 DDR: Dialing cause ip (s=10.232.3.3, d=10.76.0.99)

Mar 12 12:52:15 EST: BR0 DDR: Attempting to dial xxxxxxxxx

Mar 12 12:52:15 EST: ISDN BR0: TX -> SETUP pd = 8 callref = 0x17

Mar 12 12:52:15 EST: Bearer Capability i = 0x8890218F

Mar 12 12:52:15 EST: Channel ID i = 0x83

Mar 12 12:52:15 EST: Keypad Facility i = 'xxxxxxxxxxx'

Mar 12 12:52:15 EST: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0x97

Mar 12 12:52:15 EST: Channel ID i = 0x89

Mar 12 12:52:15 EST: Locking Shift to Codeset 5

Mar 12 12:52:15 EST: Codeset 5 IE 0x2A i = 70x80880B, 'xxxxxxxxx', 0x800109800114800114800114

Mar 12 12:52:17 EST: ISDN BR0: RX <- DISCONNECT pd = 8 callref = 0x97

Mar 12 12:52:17 EST: Cause i = 0x829F - Normal, unspecified

Mar 12 12:52:17 EST: ISDN BR0: TX -> RELEASE pd = 8 callref = 0x17

Mar 12 12:52:17 EST: BRI0: wait for isdn carrier timeout, call id=0x8115

Mar 12 12:52:17 EST: DDR: Dialing failed, 2 packets unqueued and discarded

Mar 12 12:52:17 EST: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0x97

Mar 12 12:52:18 EST: BR0 DDR: rotor dialout [priority]

Mar 12 12:52:18 EST: BR0 DDR: Dialing cause ip (s=10.232.3.3, d=10.1.0.99)

Mar 12 12:52:18 EST: BR0 DDR: Attempting to dial xxxxxxxxxxx

Mar 12 12:52:18 EST: ISDN BR0: TX -> SETUP pd = 8 callref = 0x18

Mar 12 12:52:18 EST: Bearer Capability i = 0x8890218F

Mar 12 12:52:18 EST: Channel ID i = 0x83

Mar 12 12:52:18 EST: Keypad Facility i = 'xxxxxxxx'

Mar 12 12:52:18 EST: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0x98

Mar 12 12:52:18 EST: Channel ID i = 0x89

Mar 12 12:52:18 EST: Locking Shift to Codeset 5

Mar 12 12:52:18 EST: Codeset 5 IE 0x2A i = 0x80880B, 'xxxxxxxxxxx', 0x800109800114800114800114

Smithkline-college(config-if)#

Mar 12 12:52:22 EST: ISDN BR0: RX <- PROGRESS pd = 8 callref = 0x98

Mar 12 12:52:22 EST: Progress Ind i = 0x8A81 - Call not end-to-end ISDN, may have in-band info

Mar 12 12:52:23 EST: ISDN BR0: RX <- CONNECT pd = 8 callref = 0x98

Mar 12 12:52:23 EST: Progress Ind i = 0x8482 - Destination address is non-ISDN

Mar 12 12:52:23 EST: ISDN BR0: TX -> CONNECT_ACK pd = 8 callref = 0x18

Mar 12 12:52:23 EST: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up

Mar 12 12:52:23 EST: %DIALER-6-BIND: Interface BR0:1 bound to profile Di1

Mar 12 12:52:43 EST: BR0 DDR: has total 0 call(s), dial_out 0, dial_in 0

Mar 12 12:52:43 EST: %DIALER-6-UNBIND: Interface BR0:1 unbound from profile Di1

Mar 12 12:52:43 EST: BR0:1 DDR: disconnecting call

Mar 12 12:52:43 EST: %ISDN-6-DISCONNECT: Interface BRI0:1 disconnected from xxxxxxxxxx , call lasted 20 seconds


xxxxxxxxxxxxxxx added second dial string xxxxxxxxxxxxxxxxxxxxxxxxxxx


Mar 12 12:56:47 EST: BR0 DDR: rotor dialout [priority]

Mar 12 12:56:47 EST: BR0 DDR: Dialing cause ip (s=10.6.95.232, d=10.76.0.101)

Mar 12 12:56:47 EST: BR0 DDR: Attempting to dial 5555555

Mar 12 12:56:47 EST: ISDN BR0: TX -> SETUP pd = 8 callref = 0x1B

Mar 12 12:56:47 EST: Bearer Capability i = 0x8890218F

Mar 12 12:56:47 EST: Channel ID i = 0x83

Mar 12 12:56:47 EST: Keypad Facility i = '5555555'

Mar 12 12:56:47 EST: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0x9B

Mar 12 12:56:47 EST: Channel ID i = 0x89

Mar 12 12:56:47 EST: Locking Shift to Codeset 5

Mar 12 12:56:47 EST: Codeset 5 IE 0x2A i = 0x80880B, '15555555', 0x800109800114800114800114.

Mar 12 12:56:48 EST: ISDN BR0: RX <- DISCONNECT pd = 8 callref = 0x9B

Mar 12 12:56:48 EST: Cause i = 0x829F - Normal, unspecified

Mar 12 12:56:48 EST: ISDN BR0: TX -> RELEASE pd = 8 callref = 0x1B

Mar 12 12:56:48 EST: BRI0: wait for isdn carrier timeout, call id=0x8119

Mar 12 12:56:48 EST: BR0 DDR: Attempting to dial 10102205555555555

Mar 12 12:56:48 EST: ISDN BR0: TX -> SETUP pd = 8 callref = 0x1C

Mar 12 12:56:48 EST: Bearer Capability i = 0x8890

Mar 12 12:56:48 EST: Channel ID i = 0x83

Mar 12 12:56:48 EST: Keypad Facility i = '101022055555555555'

Mar 12 12:56:48 EST: ISDN BR0: RX <- RELEASE_COMP pd = 8 callref = 0x9B

Mar 12 12:56:49 EST: ISDN BR0: RX <- CALL_PROC pd = 8 callref = 0x9C

Mar 12 12:56:49 EST: Channel ID i = 0x89

Mar 12 12:56:49 EST: Locking Shift to Codeset 5

Mar 12 12:56:49 EST: Codeset 5 IE 0x2A i = 0x808812, '1010220555555555555555', 0x800102800114800114800114.!!!

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
makchitale Wed, 03/12/2003 - 10:43
User Badges:
  • Silver, 250 points or more

The very fact that the call goes thru using the 1010220 should be good enough for the telco....there seems to be an issue on the path the call takes without the 1010220 prefix....


Try locking the speed to 56k,

dialer map ip speed 56 name abc xxxx

OR

dialer string xxxx class 123

map-class dialer 123

dialer isdn speed 56


Thanks, Mak.

makchitale Wed, 03/12/2003 - 20:22
User Badges:
  • Silver, 250 points or more

You probably have dialer Profiles configured (dialer pool xx)....On a non-DDR interface, for legacy ddr we need "dialer in-band" to add any dialer commands but for Dialer profiles we need "dialer pool" for adding any more dialer commands.


show run / sh ver.


Thanks, Mak.

Actions

This Discussion