cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
284
Views
0
Helpful
1
Replies

Firewall Services Module (FWSM) with SUP1A plus MSFC-2 & PFC (CatOS 7.5+)

iferras
Level 1
Level 1

Is it possible to install a FWSM on a C6509 with SUP1A?

Release Notes for FWSM version 1-1-2(http://www.cisco.com/en/US/partner/products/hw/switches/ps708/prod_release_note09186a008015851e.html#43499) states that FWSM is supported with CatOS 7.5 with a Supervisor Engine 1a, and an MSFC 2 or a Supervisor Engine2 and an MSFC 2.

However, Cisco Configuration Tool gives the following message when you try to configure FWSM with SUP1A:

Configuration Guide

Errors

1. --The selection of one or more WS-SVC-FWM-1-K9 firewall modules requires the selection of a Supervisor2 with MSFC from Cat6500 Primary Supervisor Option. Please adjust your selections.--

1 Accepted Solution

Accepted Solutions

Prashanth Krishnappa
Cisco Employee
Cisco Employee

It's probably a bug in the configurator tool. It is supported with Sup1

Console> (enable) sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- ---

--------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok

2 2 6 Firewall Module WS-SVC-FWM-1 no ok

3 3 8 1000BaseX Ethernet WS-X6408-GBIC no ok

5 5 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok

Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAD044505P9

15 SAD04420LM7

2 SAD071903GJ

3 SAD03070279

5 SAD041500VP

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ----------

-----------------

1 00-01-63-d0-6c-d8 to 00-01-63-d0-6c-d9 7.0 5.3(1) 7.6(1)

00-01-63-d0-6c-d6 to 00-01-63-d0-6c-d7

00-02-17-77-98-00 to 00-02-17-77-9b-ff

15 00-04-4d-47-bd-c0 to 00-04-4d-47-bd-ff 1.1 12.1(11b)E

12.1(11b)E11

2 00-0c-85-3f-f5-80 to 00-0c-85-3f-f5-ff 2.0 7.2(1) 1.1(2)

3 00-50-54-6c-92-b0 to 00-50-54-6c-92-b7 1.9 5.4(2) 7.6(1)

5 00-01-97-49-8b-10 to 00-01-97-49-8b-3f 1.2 5.1(1)CSX 7.6(1)

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

Sub-Sw

--- ----------------------- ------------------- ----------- ------

------

1 L3 Switching Engine WS-F6K-PFC SAD04440FFV 1.1

View solution in original post

1 Reply 1

Prashanth Krishnappa
Cisco Employee
Cisco Employee

It's probably a bug in the configurator tool. It is supported with Sup1

Console> (enable) sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- ---

--------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok

2 2 6 Firewall Module WS-SVC-FWM-1 no ok

3 3 8 1000BaseX Ethernet WS-X6408-GBIC no ok

5 5 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok

Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAD044505P9

15 SAD04420LM7

2 SAD071903GJ

3 SAD03070279

5 SAD041500VP

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ----------

-----------------

1 00-01-63-d0-6c-d8 to 00-01-63-d0-6c-d9 7.0 5.3(1) 7.6(1)

00-01-63-d0-6c-d6 to 00-01-63-d0-6c-d7

00-02-17-77-98-00 to 00-02-17-77-9b-ff

15 00-04-4d-47-bd-c0 to 00-04-4d-47-bd-ff 1.1 12.1(11b)E

12.1(11b)E11

2 00-0c-85-3f-f5-80 to 00-0c-85-3f-f5-ff 2.0 7.2(1) 1.1(2)

3 00-50-54-6c-92-b0 to 00-50-54-6c-92-b7 1.9 5.4(2) 7.6(1)

5 00-01-97-49-8b-10 to 00-01-97-49-8b-3f 1.2 5.1(1)CSX 7.6(1)

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

Sub-Sw

--- ----------------------- ------------------- ----------- ------

------

1 L3 Switching Engine WS-F6K-PFC SAD04440FFV 1.1