router doesn't get passed SNMP agent on host is undergoing a cold start

Unanswered Question
Oct 3rd, 2004

I have a 2503 and a 2501 router that both gets stuck at "SNMP agent on host is undergoing a cold start"

I'v had it running for about 30 minutes no changes, ios is 12.2.

I'm now learing cisco in case some of you are wondering, thanks for your help

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Average Rating: 0 (0 ratings)
gpauwen Sun, 10/03/2004 - 06:07

Hello,

have any of these routers ever booted properly ? You either have a Flash (hardware) problem or an IOS bug. Can you post the entire boot sequence ?

You could try to install a different IOS version, using the ROMMON recovery procedure, here is the link:

ROMmon Recovery for the Cisco 2500, 3000, AS5100, and uBR900 Series Routers

http://www.cisco.com/en/US/partner/products/hw/routers/ps233/products_tech_note09186a008009464c.shtml

Regards,

Georg

www.solutionfinders.nl

kimrajsohan Sun, 10/03/2004 - 15:58

Hello Georg

They were all working fine, another collegue of my was using them.

i hope this is what you were looking for:

Cisco Internetwork Operating System Software) 1986-2002 by cisco Systems, Inc.

IOS (tm) 2500 Software (C2500-JS-L), Version 12.2(7), RELEASE SOFTWARE (fc1)

Image text-base: 0x03079490, data-base: 0

Copyright (c) 1986-2002 b

cisco 2500 (68030) processor (revision A) with 16384K/2048K bytes of memory.

Bridging software.

X.25 software, Ve

Processor board ID 01231602, with hardware revision 00000000copyright 1990 by Meridian Technology Corp).

Bridging software.

X.25 software, Version 3.0.0.copyright 1990 by Meridian Te

SuperLAT software (copyright 1990 by Meridian Technology Corp).

Cisco-ET Extended Temperature platform.

TN3270 Emulation software.

1 Ethernet/IEEE 802.3

Cisco-ET Extended Temperature platform.

2 Serial network interface(s)

1 Ethernet/IEEE 802.3 interface(s)s of non-volatile configuration me

2 Serial network interface(s)

16384K

32K bytes of non-volatile configuration memor

Press RETURN to get started!

00:00:09: %LINK-3-UPDOWN: Interface Ethernet0, changed state to uphanged state to down

00:00:09: %LINK-3-UPDOWN: Interface Serial0, changed state to downhanged state to down

00:00:10: %LINK-3-UPDOWN: Interface Serial1, changed state to downn Interface Ethernet0, changed stn

00:00:27: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0, changed stnine protocol on Interface Serial0, changed statn

00:00:31: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed statnine protocol on Interface Serial1, changed statn

00:00:32: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial-CONFIG_I: Configured fr

IOS (tm) 2500 Software (C2500-J

Cisco Internetwork Operating System Software

IOS (tm) 2500 Software (C2500-JS-L), Version 12.2(7), RELEASE SOFTWARE (fc1)

Compiled Tue 15-Jan-02 20:14 by

Copyright (c) 1986-2002 by cisco Systems, Inc.01:19: %SNMP-5-COLDSTART: SNMP agent on host R

Compiled Tue 15-Jan-02 20:14 by pwade

00:01:19: %SNMP-5-COLDSTART: SNMP agent on host Rack105R2 is undergoing a cold

Here is another message i've noticed after rebooting the router.

Copyright (c) 1986-1995 by cisco Systemsocol on Interface Serial0, changed statn

2500 processor with 16384 Kbytes of main memory

00:00:35: %LIN

Loading cisco2-2500 ... [timed out]erface Serial1, changed statn

File read failed -- Time out

System Bootstrap, Version 5.2(8a), RELEASE SOFTWAREstarted --

Copyright (c) 1986-1995 by cisco SystemsSoftware

2500 processor with 16384 Kbytes of main memory, Version 12.2(7), RELEASE SOFTW

also i was unable to get to your page, i signed in but nothing, bad day for me today

w.iqbal Wed, 12/29/2010 - 01:33

Dear,

I am facing this problem please help out.

*Mar  1 00:00:30.617: %SNMP-5-COLDSTART: SNMP agent on host R1 is undergoing a cold start

After this message router goes on hanged

Regards,

Faisal

program load complete, entry point: 0x80008000, size: 0x132f0b0

Self decompressing the image : ################################################################################################################################################################################################################################################################################################################ [OK]

Smart Init is enabled

smart init is sizing iomem

  ID            MEMORY_REQ                 TYPE

00036B          0X00103980 C2611XM Dual Fast Ethernet

                0X00098670 public buffer pools

                0X00211000 public particle pools

TOTAL:          0X003ACFF0

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 4Mb.

Using 3 percent iomem. [4Mb/128Mb]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.

           170 West Tasman Drive

           San Jose, California 95134-1706

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(21), RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Mon 06-Nov-06 13:41 by ccai

Image text-base: 0x80008098, data-base: 0x81DDA2A8

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

export@cisco.com.

cisco 2611XM (MPC860P) processor (revision 0x100) with 126976K/4096K bytes of memory.

Processor board ID JAD07080P6P (1147248223)

M860 processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Slot is empty or does not support clock participate

WIC slot is empty or does not support clock participate

interface Serial0/0

          ^

% Invalid input detected at '^' marker.

ip address 19.19.125.1 255.255.255.0

           ^

% Invalid input detected at '^' marker.

encapsulation frame-relay

   ^

% Invalid input detected at '^' marker.

no fair-queue

      ^

% Invalid input detected at '^' marker.

frame-relay map ip 19.19.125.2 105 broadcast

             ^

% Invalid input detected at '^' marker.

frame-relay map ip 19.19.125.5 105 broadcast

             ^

% Invalid input detected at '^' marker.

no frame-relay inverse-arp

                ^

% Invalid input detected at '^' marker.

frame-relay lmi-type cisco

             ^

% Invalid input detected at '^' marker.

interface Serial0/1

          ^

% Invalid input detected at '^' marker.

ip address 19.19.13.1 255.255.255.0

           ^

% Invalid input detected at '^' marker.

encapsulation frame-relay

   ^

% Invalid input detected at '^' marker.

frame-relay map ip 19.19.13.3 103 broadcast

             ^

% Invalid input detected at '^' marker.

no frame-relay inverse-arp

                ^

% Invalid input detected at '^' marker.

frame-relay lmi-type cisco

             ^

% Invalid input detected at '^' marker.

Press RETURN to get started!

*Mar  1 00:00:05.897: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up

*Mar  1 00:00:23.045: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up

*Mar  1 00:00:23.045: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up

*Mar  1 00:00:24.291: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down

*Mar  1 00:00:24.291: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down

*Mar  1 00:00:26.318: %SYS-5-CONFIG_I: Configured from memory by console

*Mar  1 00:00:30.617: %SYS-5-RESTART: System restarted --

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(21), RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Mon 06-Nov-06 13:41 by ccai

*Mar  1 00:00:30.617: %SNMP-5-COLDSTART: SNMP agent on host R1 is undergoing a cold start

muhammad.faisal@dwp.com.pk

Actions

Login or Register to take actions

This Discussion

Posted October 3, 2004 at 4:07 AM
Stats:
Replies:5 Avg. Rating:
Views:2048 Votes:0
Shares:0
Tags: No tags.

Discussions Leaderboard

Rank Username Points
1 2,069
2 1,736
3 1,675
4 1,624
5 1,529