12-02-2005 04:09 PM - edited 03-03-2019 01:00 AM
I'm receiving this on a 3825:
program load complete, entry point: 0x8000f000, size: 0xc0c0
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xc0c0
Initializing ATA monitor library.......
loadprog: error - on read during ELF program load
requested 27157520 (0x19e6410) bytes, got 16748852 (0xff9134)
open: failed to find and/or load the bootloader: "flash:c3825-spservicesk9-mz.123-11.T8.bin"
loadprog: error - on file open
boot: cannot load "c3825-spservicesk9-mz.123-11.T8.bin"
System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2004 by cisco Systems, Inc.
System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2005 by cisco Systems, Inc.
Total memory size = 256 MB - DIMM0 = 256 MB, DIMM1 = 0 MB
c3825 processor with 262144 Kbytes of main memory
Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xc0c0
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xc0c0
Initializing ATA monitor library.......
loadprog: error - on read during ELF program load
requested 27157520 (0x19e6410) bytes, got 16748852 (0xff9134)
boot: cannot load "flash:"
System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2004 by cisco Systems, Inc.
System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2005 by cisco Systems, Inc.
Total memory size = 256 MB - DIMM0 = 256 MB, DIMM1 = 0 MB
c3825 processor with 262144 Kbytes of main memory
Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled
Upgrade ROMMON initialized
program load complete, entry point: 0x8000f000, size: 0xc0c0
Initializing ATA monitor library.......
program load complete, entry point: 0x8000f000, size: 0xc0c0
Initializing ATA monitor library.......
loadprog: error - on read during ELF program load
requested 27157520 (0x19e6410) bytes, got 16748852 (0xff9134)
boot: cannot load "flash:"
System Bootstrap, Version 12.3(11r)T1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2004 by cisco Systems, Inc.
System Bootstrap, Version 12.3(11r)T2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2005 by cisco Systems, Inc.
Total memory size = 256 MB - DIMM0 = 256 MB, DIMM1 = 0 MB
c3825 processor with 262144 Kbytes of main memory
Main memory is configured to 72/0(dimm 0/1) bit mode with ECC enabled
Upgrade ROMMON initialized
rommon 1 >
12-02-2005 04:55 PM
Appears, the IOS image is corrupted.
Follow the link below to load a valid image.
http://www.cisco.com/en/US/products/ps5854/prod_configuration_guide09186a00802c35e9.html#wp1051098
Good Luck!!
HTH,
Sundar
12-03-2005 10:02 AM
You should be able to use the CF slot on 3825 , copy an image into the CF card and boot from it from rommon.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: