Solved: EIGRP Routing Question

AmnardC04 · ‎01-17-2006

interface Vlan110

ip address 136.160.196.1 255.255.255.0

!

interface Vlan310

ip address 136.160.197.1 255.255.255.192

!

interface Vlan610

ip address 192.168.180.1 255.255.255.0

!

interface Vlan710

ip address 192.168.150.1 255.255.255.0

!

interface Vlan910

ip address 192.168.254.84 255.255.255.248

!

router eigrp 411

network 136.160.0.0

network 192.168.0.0

no auto-summary

!

ip classless

ip route 0.0.0.0 0.0.0.0 192.168.254.81

=======================================

Core-SC1#sh ip route

Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2

ia - IS-IS inter area, * - candidate default, U - per-user static route

o - ODR, P - periodic downloaded static route

Gateway of last resort is 192.168.254.81 to network 0.0.0.0

136.160.0.0/16 is variably subnetted, 2 subnets, 2 masks

C 136.160.196.0/24 is directly connected, Vlan110

C 136.160.197.0/26 is directly connected, Vlan310

C 192.168.150.0/24 is directly connected, Vlan710

C 192.168.180.0/24 is directly connected, Vlan610

192.168.254.0/29 is subnetted, 1 subnets

C 192.168.254.80 is directly connected, Vlan910

S* 0.0.0.0/0 [1/0] via 192.168.254.81

Core-SC1#sh ip eigrp top

IP-EIGRP Topology Table for AS(411)/ID(192.168.254.84)

Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply,

r - reply Status, s - sia Status

P 136.160.196.0/24, 1 successors, FD is 2816

via Connected, Vlan110

P 136.160.197.0/26, 1 successors, FD is 2816

via Connected, Vlan310

=======================================

Why wouldn't subnets in 192.168.0.0 network show up in the "sh ip eigrp top"?

pkhatri · ‎01-17-2006

Hi,

Try replacing your 'network 192.168.0.0' statement under router eigrp with 'network 192.168.0.0 0.0.255.255'.

By default, if a mask is not specified, the network statement is treated as a classful network and in your case, the mask would default to 0.0.0.255

Hope that helps - pls rate the post if it does.

Regards,

Paresh

View solution in original post

pkhatri · ‎01-17-2006

Hi,

Try replacing your 'network 192.168.0.0' statement under router eigrp with 'network 192.168.0.0 0.0.255.255'.

By default, if a mask is not specified, the network statement is treated as a classful network and in your case, the mask would default to 0.0.0.255

Hope that helps - pls rate the post if it does.

Regards,

Paresh

Richard Burts · ‎01-17-2006

I think that the answer given by Paresh is one correct alternative. Another alternative is to replace the one network statement for 192.168.0.0 with two network statements, one for each of the class C 192.168 networks on the interfaces.

Another way to understand the impact of the original configuration is to do the command show ip eigrp interface. If you do this you will see that neither of the 192.168 interfaces are currently included in EIGRP since they do not match the 192.168.0.0 network statement.

HTH

Rick

HTH

Rick

AmnardC04 · ‎01-17-2006

That's it! Thank a lot!!!

I couldn't believe I missed something this simple...