×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

CCM to CCM

Unanswered Question
Feb 9th, 2006
User Badges:

Just to know how to set up connection so I can access extension from one CCM to another, using intercluster trunk non-gk. Do i have to setup intercluster in both CCM? and what more?.


Thanks

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 3 (2 ratings)
Loading.
Brandon Buffin Thu, 02/09/2006 - 04:20
User Badges:
  • Purple, 4500 points or more

You'll need to setup intercluster trunks and configure route patterns on both CCMs. The route pattern can point directly to the trunk or to a route list containing a route group to which you've added the trunk.


Hope this helps. If so, please rate the post


Brandon

zanini Thu, 02/09/2006 - 05:49
User Badges:

Yes, but I don´t know if I need something more. Both CCM are 4.1, locations have different extension range, route patterns are set and seem to be working, but no way. Is there something more?


Again Thanks

Brandon Buffin Thu, 02/09/2006 - 07:53
User Badges:
  • Purple, 4500 points or more

What happens when you try to make a call between clusters? It's important to remember that the Callmanager servers defined for a given intercluster trunk must correspond to the Callmanager servers that are defined as members of the Callmanager group assigned to the device pool associated with the remote trunk. The reverse must also be true for the configuration of the remote trunk. Please take a look at the following link.


http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_implementation_design_guide_chapter09186a008044751e.html#wp1045593


Hope this helps. If so, please rate the post.


Brandon

zanini Thu, 02/09/2006 - 09:06
User Badges:

We are getting closer but not yet. This is my situation: 2 CCM, on in Spain and other in USA, both are standalone CCM. I need to know what i have to create in each CCM in order to dial between them. I have the trunk created, route patterns working, and missing something because is not working ??


Thanks


Chris Deren Thu, 02/09/2006 - 09:14
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

Couple of questions that can give you clue where to find the problem:



1. Do the phones' Calling Search Space have access to the route pattern partion?

2. Does the Calling Search space applied to the Trunk have access to the phone's calling search space?

3. What do you have set for significant digits on the Trunk?

4. what does your dial plan look like in Spain and US CCM, is it 4 digit in both locations? What are your route patterns on both sides?

5. What are you hearing when you dial, fastbusy?



Chris


mparekh Sun, 02/12/2006 - 17:40
User Badges:
  • Bronze, 100 points or more

Try using Digit Analyzer to make sure that the call is using the right route pattern.

jleon22 Thu, 05/04/2006 - 06:26
User Badges:
  • Bronze, 100 points or more

You can use Locations to control bandwidth usage.

mohamedtag Thu, 05/04/2006 - 12:05
User Badges:

Hello All ,


I am having the same problem that Zanini is facing. My setup are as follows :


1 - 2 CCM's Version 3.3(4).

2 - On both CCM Servers i have created Intercluster Trunk Non GK Controlled.

3 - On Each CCM a Route Pattern Points to the Trunk in the Route List Field.

4 - When i try to dial from one side the other Extension on the other side , i receive Fast Busy Tone.


I Will try to delete the Whole Configuration and create it from the Scratch maybe i missed something related to the CSS's and will update you.


Regards


M.Tag



thisisshanky Thu, 05/04/2006 - 15:04
User Badges:
  • Purple, 4500 points or more

Have you reset the trunk after you created it ?

Actions

This Discussion