cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
601
Views
5
Helpful
6
Replies

QoS question

Ahmede
Level 1
Level 1

Guys,

I have 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX card, and I thought it using 1p3q8t techniques, but for some reason when i try to add this configuration to any interface on the card

wrr-queue bandwidth 5 25 70

wrr-queue queue-limit 5 25 40

wrr-queue cos-map 1 1 1

wrr-queue cos-map 2 1 0

wrr-queue cos-map 3 1 4

wrr-queue cos-map 3 2 2

wrr-queue cos-map 3 3 3

wrr-queue cos-map 3 4 6

wrr-queue cos-map 3 5 7

priority-queue cos-map 1 5

mls qos trust dscp

it does not accept some commands, shuch as wrr-queue cos-map 3 x x

And wrr-queue bandwidth 5 25 70

Does this card really supports 1p3q8t?

Thanks in advance..

6 Replies 6

Michael Stuckey
Level 3
Level 3

What do you see when you do a

"show queueing interface Gix/x" for any interface you have on that card?

I would also like to know what version of IOS you are using?

Mike

The IOS version is fine 12.2.18SXD..

Some commands work fine, such as

wrr-queue cos-map 2 2 3

But when the command wrr-queue cos-map starts with 3 it does not work, so it looks like it's only 2q not 3q, however accoring to Cisco it should be 1p3q8t..

I recently installed some 6509-E's with Sup720's and some WS-X6748-GE-TX modules and I didn't have a problem configuring this:

interface GigabitEthernet3/1

switchport

switchport access vlan 6

no ip address

wrr-queue bandwidth 5 25 70

wrr-queue queue-limit 5 25 40

wrr-queue random-detect min-threshold 3 50 60 70 80 90 100 100 100

wrr-queue random-detect max-threshold 1 100 100 100 100 100 100 100 100

wrr-queue random-detect max-threshold 2 100 100 100 100 100 100 100 100

wrr-queue random-detect max-threshold 3 60 70 80 90 100 100 100 100

wrr-queue cos-map 1 1 1

wrr-queue cos-map 2 1 0

wrr-queue cos-map 3 1 4

wrr-queue cos-map 3 2 2

wrr-queue cos-map 3 3 3

wrr-queue cos-map 3 4 6

wrr-queue cos-map 3 5 7

mls qos trust dscp

!

I was however running 12.2(18)SXF3. The documentation states the WS-X6748-GE-TX has the transmit queue structure 1P3Q8T so it should work. Are you sure it is a 6748 and not a 6548? If you do a 'show interface capabilities' it will show you what the tx queue structure is.

HTH

Andy

Thanks Andrew..

So now, is the queue structure is software dependent or hardware? I mean if I upgraded the IOS will that change the queue structure for the card?

It should be hardware dependant, although I wouldn't rule out an IOS issue. I have briefly looked through the release notes and can't see anything that looks like your problem.

I assume the output from 'show interface capabilities' show the TX queue structure as 1P3Q8T? If so either open a TAC case or just put a later IOS on. 12.2(18)SXD has been deferred anyway so it is advisable to move to 12.2(18)SXD7 (all earlier 12.2(18)SXx releases have software advisories against them).

HTH

Andy

Whoops, I meant to say:

all earlier 12.2(18)SXDx releases have software advisories against them....

Andy

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: