×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Analog phone via built-in FXS ports?

Unanswered Question
May 30th, 2006
User Badges:

Hello,


We currently have a Cisco CallManager Express implementataion with a 2811 router, 4 built-in FXS and 4 FXO ports, and (5) 7960 IP phones. We would like to use a standard cordless phone for manager only usage early in the morning.


We connected the phone to the first FXS port and are able to dial out and make calls properly as per the dial-peers that are already configured. We would like to configure this FXS port so this analog phone could function similar to an IP phone (answering incoming calls, possibly transfer and on-hold functions).


I've read the CCME admin guide and the guide on voice ports, but I'm having trouble with the solution. I understand that it needs to be configured as an ephone, but how do I configure the ephone to point to the FXS port? Or am I way off base?


Thanks in advance!

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Aaron Harrison Tue, 05/30/2006 - 22:47
User Badges:
  • Super Bronze, 10000 points or more
  • Community Spotlight Award,

    Member's Choice, May 2015

Hi


You don't need to create an ephone - the internal voice ports are real ports so don't need the virtual construct.


All you need to do is configure the voice-port that is already in your config appropriately, then create a dial-peer x pots to point at it... e.g:


voice-port 0/0

cptone GB


dial-peer voice 1 pots

destination-pattern 1234

port 0/0



This should get basic calling in working...


Regards


Aaron


Please rate helpful posts

aceprecision-jasonl Wed, 05/31/2006 - 06:42
User Badges:

Maybe I should clarify. This is a complete CME installed and working with 5 IP phones. People can call in and out with the IP phones, and everything works exactly like it should. I just want to give them the ability to use a cordless phone via the built in FXS port. If I plug in the analog phone to the FXS port, that phone can dial out according to the dial-peers already configured.


Now, I want to give them the ability to answer an incoming call. So basically, when a call comes in the FXO port, I want this analog phone connected to the FXS port to ring also...giving the user the ability to answer that phone if they aren't near an IP phone.


I hope that clears things up...Thanks for the help!


aceprecision-jasonl Wed, 05/31/2006 - 07:03
User Badges:

Here is a sanitized config from the router:



voice-port 0/0/0

supervisory disconnect anytone

connection plar opx 150

description FXO-xxx-xxx-xxxx

station-id name Outside Line

!

voice-port 0/0/1

supervisory disconnect anytone

connection plar opx 151

description FXO-xxx-xxx-xxxx

station-id name Outside Line

!

voice-port 0/0/2

supervisory disconnect anytone

connection plar opx 152

description FXO-xxx-xxx-xxxx

station-id name Outside Line

!

voice-port 0/0/3

description FXO-Unused

!

voice-port 0/1/0

description Cordless Phone

station-id name Cordless Phone

caller-id enable

!

voice-port 0/1/1

!

voice-port 0/1/2

!

voice-port 0/1/3

!

!

!

!

!

dial-peer voice 201 pots

preference 3

destination-pattern 91..........

port 0/0/1

forward-digits 11

!

dial-peer voice 202 pots

preference 2

destination-pattern 91..........

port 0/0/2

forward-digits 11

!

dial-peer voice 200 pots

preference 4

destination-pattern 91..........

port 0/0/0

forward-digits 11

!

dial-peer voice 100 pots

preference 4

destination-pattern 9[2-9]......

port 0/0/0

forward-digits 7

!

dial-peer voice 101 pots

preference 3

destination-pattern 9[2-9]......

port 0/0/1

forward-digits 7

!

dial-peer voice 102 pots

preference 2

destination-pattern 9[2-9]......

port 0/0/2

forward-digits 7

!

dial-peer voice 300 pots

preference 4

destination-pattern 9T

port 0/0/0

!

dial-peer voice 301 pots

preference 3

destination-pattern 9T

port 0/0/1

!

dial-peer voice 302 pots

preference 2

destination-pattern 9T

port 0/0/2

!

dial-peer voice 400 pots

description Local FAX on router

destination-pattern 160

port 0/1/0

!

!

!

!

telephony-service

load 7910 P00403020214

load 7960-7940 P00305000600

max-ephones 36

max-dn 144

ip source-address 192.168.10.254 port 2000

create cnf-files version-stamp Jan 01 2002 00:00:00

max-conferences 8 gain -6

moh music-on-hold-1.wav

multicast moh 239.1.1.1 port 2000 route 192.168.10.254

transfer-system full-consult

secondary-dialtone 9

!

!

ephone-dn 1

number 150

label Line-1

description Outside Line 1

hold-alert 30 shared

!

!

ephone-dn 2

number 151

label Line-2

hold-alert 30 shared

!

!

ephone-dn 3

number 152

label Line-3

hold-alert 30 shared

!

!

ephone-dn 100

number 100

label location0 100

description xxx-xxx-xxxx

name Office

!

!

ephone-dn 101

number 101

label location1 101

description xxx-xxx-xxxx

name location1

!

!

ephone-dn 102

number 102

label location2 102

description xxx-xxx-xxxx

name location2

!

!

ephone-dn 103

number 103

label location3 103

description xxx-xxx-xxxx

name location3

!

!

ephone-dn 104

number 104

label location4 104

description xxx-xxx-xxxx

name location4

!

!

ephone-dn 105

number 105

label location5 105

description xxx-xxx-xxxx

name location5

!

!

!

!

ephone 1

mac-address xxxx.xxxx.xxxx

type 7960

button 1:100 2:1 3:2 4:3

!

!

!

ephone 2

mac-address xxxx.xxxx.xxxx

type 7960

button 1:101 2:1 3:2 4:3

!

!

!

ephone 3

mac-address xxxx.xxxx.xxxx

type 7960

button 1:102 2:1 3:2 4:3

!

!

!

ephone 4

mac-address xxxx.xxxx.xxxx

type 7960

button 1:103 2:1 3:2 4:3

!

!

!

ephone 5

mac-address xxxx.xxxx.xxxx

type 7960

button 1:104 2:1 3:2 4:3

!

!

!

ephone 6

mac-address xxxx.xxxx.xxxx

type 7960

button 1:105 2:1 3:2 4:3


Actions

This Discussion