×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

HELP required !!!

Unanswered Question
Jun 2nd, 2006
User Badges:

I want to know wheather I can make and receive SIP calls. My Router Configuration is as follows:


Router - 1751

IOS Image Name: c1700-sv8y7-mz.123-2T9.bin

IOS Version: 12.3(2)T9

Feature Sets: IP (Internet Protocol)


Hardware Details

Model Type: Cisco 1751

Total Memory: 64 MB

Total Flash Capacity: 16 MB

Boot From: flash


Hardware Configuration


Slot 0: C1751 Mainboard

#10/100Ethernet

#WIC Slot 0: 1 Port Ethernet (WIC-1ENET)

# WIC Slot 1: 2 Port FXS (VIC-2FXS)

# WIC Slot 2: 2 Port FXO (VIC-2FXO)




This Unit is installed in New Delhi. Broadband connection from MTNL New Delhi with Static IP Address.

I have SIP account with www.web.de in Germany. And I want to make and receive calls from Germany.


Please HELP!!!

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
gpulos Fri, 06/02/2006 - 03:09
User Badges:
  • Blue, 1500 points or more

the IOS should be upgraded to 12.3.7T12.


previous releases have been defered and you'll need the ip voice feature set.


this does require 96MB ram and 32MB flash though.

chopra Fri, 06/02/2006 - 04:19
User Badges:

As per my informations, upgrading of Flash in Cinsco 1751 is not possible.

Is there any other way, where I do not have to upgrade the memory.

tdrais Fri, 06/02/2006 - 09:39
User Badges:
  • Blue, 1500 points or more

You need to upgrade the ram which appear is possible.


You should be able to boot the router from a TFTP server. Not sure I would do this for a production router but i have done it many times in the lab.

how about my version? could an FXS or FXO card can work without upgrading the mem or IOS? Please see below



Cisco Internetwork Operating System Software

IOS (tm) C1700 Software (C1700-K8O3SY7-M), Version 12.2(8)T5, RELEASE SOFTWARE)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2002 by cisco Systems, Inc.

Compiled Fri 21-Jun-02 19:24 by ccai

Image text-base: 0x80008108, data-base: 0x80D2EACC


ROM: System Bootstrap, Version 12.2(1r)XE1, RELEASE SOFTWARE (fc1)

ROM: C1700 Software (C1700-Y-M), Version 12.2(13)T1, RELEASE SOFTWARE (fc1)


cisco1751 uptime is 17 hours, 30 minutes

System returned to ROM by power-on

System image file is "flash:c1700-k8o3sy7-mz.122-8.T5.bin"


cisco 1751 (MPC860P) processor (revision 0x600) with 36864K/12288K bytes of mem.

Processor board ID JAD06390282 (3061614917), with hardware revision 0000

MPC860P processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

Basic Rate ISDN software, Version 1.1.

1 Ethernet/IEEE 802.3 interface(s)

1 FastEthernet/IEEE 802.3 interface(s)

1 ISDN Basic Rate interface(s)

1 Virtual Private Network (VPN) Module(s)

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)


Configuration register is 0x2102




Nicholas Matthews Sun, 01/18/2009 - 13:13
User Badges:
  • Red, 2250 points or more

You will not be able to use DSPs, voice cards, or voice protocols without a voice image.


For the 1700 you can identify a voice image if it has a 'v' in the IOS name.



hth,

nick

Actions

This Discussion