cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
721
Views
0
Helpful
4
Replies

IP Address lost after reboot

pwenger
Level 3
Level 3

Hi

I have got a ASA 5510 running 7.2.1.

The outside interface recieves the IP address over pppoe. Normaly you don't need to configure a fix IP with pppoe, but for any reason I don't recieve an IP address until I hardcode it on the ASA. Then when I reboot the ASA the IP address of the outside interface is lost.Further, I'm not able to change the subnetmask, it changes always to a host subnetmask. Has someone already made the same experience? See below the configuration of the outside interface and the pppoe statements.

interface Ethernet0/0

nameif outside

security-level 0

pppoe client vpdn group any

ip address XXX.XXX.XXX.XXX 255.255.255.255 pppoe setroute

vpdn group any request dialout pppoe

vpdn group any localname username@switzerland.net

vpdn group any ppp authentication chap

vpdn username username@switzerland.net password ***** store-local

Best regards

Peter

4 Replies 4

cpembleton
Level 4
Level 4

Did you configure the ip address to request an IP from DHCP?

ip address dhcp ppoe setroute

Thanks,

Chad

Please reate if this helps!

Hi Chad,

yes I tried it, but I never recieve an IP address and I never get a connection.

Regards

Peter

Hi Chad,

Sorry to ask the obvious, but have you done some debugging of pppoe?

Check out http://www.cisco.com/en/US/products/ps6120/products_configuration_guide_chapter09186a008066ebe6.html#wp85837

Specifically "Monitoring and Debugging the PPPoE Client".

Could you please do 'debug pppoe event' and 'debug pppoe error' and paste them in here?

Thanks,

Glen

Hi Glen

I figured out now the bug. When I enter the IP address at the outside interface with for example a /30 subnetmask, it takes this command, but for any reason it changes the mask to /32 when you have a look in the running config a few seconds after you entered the command.

See this below:

ciscoasa(config-if)# ip address 213.200.233.189 255.255.255.252 pppoe setroutPPPoE is already enabled on outside interface - now clearing

ciscoasa(config-if)# sh int e0/0

Interface Ethernet0/0 "outside", is up, line protocol is up

Hardware is i82546GB rev03, BW 100 Mbps

Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)

MAC address 0012.d949.147e, MTU 1500

IP address unassigned

58 packets input, 4483 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort

0 L2 decode drops

61 packets output, 4678 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets

0 babbles, 0 late collisions, 0 deferred

0 lost carrier, 0 no carrier

input queue (curr/max blocks): hardware (1/0) software (0/0)

output queue (curr/max blocks): hardware (0/3) software (0/0)

Traffic Statistics for "outside":

91 packets input, 5419 bytes

61 packets output, 2973 bytes

0 packets dropped

1 minute input rate 1 pkts/sec, 64 bytes/sec

1 minute output rate 0 pkts/sec, 34 bytes/sec

1 minute drop rate, 0 pkts/sec

5 minute input rate 0 pkts/sec, 0 bytes/sec

5 minute output rate 0 pkts/sec, 0 bytes/sec

5 minute drop rate, 0 pkts/sec

ciscoasa(config-if)#

ciscoasa(config-if)#

ciscoasa(config-if)#

ciscoasa(config-if)#

ciscoasa(config-if)#

ciscoasa(config-if)# sh run int e0/0

!

interface Ethernet0/0

nameif outside

security-level 0

pppoe client vpdn group any

ip address 213.200.233.189 255.255.255.252 pppoe setroute

ciscoasa(config-if)#

ciscoasa(config-if)#

ciscoasa(config-if)#

ciscoasa(config-if)# sh run int e0/0

!

interface Ethernet0/0

nameif outside

security-level 0

pppoe client vpdn group any

ip address 213.200.233.189 255.255.255.255 pppoe setroute

ciscoasa(config-if)#

Then when you reboot you get the following message:

ERROR: Bad mask 255.255.255.255 for address 213.200.233.189

*** Output from config line 16, " ip address 213.200.233...."

and for this message there is no IP anymore on the outside interface.

Regards

Peter

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: