08-25-2006 03:31 AM - edited 03-03-2019 01:46 PM
Hi all,
I want to upgrade my 7200 ios from the image c7200-is-mz.121-14.E10.bin
to the newer c7200-is-mz.123-20.bin and the problem I'm facing is that
after i boot with the 12.3 all of the ATM interfaces remain down down.
I wonder if newer image require some extra command to get the atm interfaces
up and running.
As I boot with my old 12.1 everything go up again
I paste the configuration concerning the ATM interface,
ima group ,PVC and the show int atm .
Thanks in advance for any advice.
Regards,
Marco.
!
interface ATM2/0
no ip address
scrambling cell-payload
framing crc4adm
ima-group 1
!
interface ATM2/1
no ip address
scrambling cell-payload
framing crc4adm
ima-group 1
!
interface ATM2/ima1
mtu 1500
bandwidth 8000
no ip address
no atm auto-configuration
no atm ilmi-keepalive
!
interface ATM2/ima1.111 point-to-point
ip address
pvc 10/111
ubr 1536
oam-pvc manage
encapsulation aal5snap
!
!
interface ATM2/ima1.121 point-to-point
ip address
pvc 10/121
ubr 1536
oam-pvc manage
encapsulation aal5snap
!
!
interface ATM2/ima1.131 point-to-point
ip address
pvc 10/131
ubr 1536
oam-pvc manage
encapsulation aal5snap
!
****** with 12.3 IOS the interface is down
ATM2/0 is down, line protocol is down
Hardware is IMA PA
MTU 4470 bytes, BW 1920 Kbit, DLY 20000 usec,
reliability 0/255, txload 0/255, rxload 1/255
Encapsulation UNKNOWN, loopback not set
Encapsulation(s): AAL5
511 maximum active VCs, 0 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
0 carrier transitions
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
***** with the 12.1 IOS the interface is UP and the keepalive set is shown.
7200B#show int atm2/0
ATM2/0 is up, line protocol is up
Hardware is IMA PA
MTU 4470 bytes, BW 1920 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation UNKNOWN, loopback not set
Keepalive set (10 sec)
Encapsulation(s): AAL5
512 maximum active VCs, 0 current VCCs
VC idle disconnect time: 300 seconds
1 carrier transitions
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
08-25-2006 04:41 AM
Hello Marco,
try and set the keepalive manually on your ATM interface:
interface ATM2/0
--> keepalive 10
I am not sure why, but in 12.3, this might be the default (no keepalive on the interface)...
HTH,
GNT
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: