×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

additional DID plan

Unanswered Question
Oct 15th, 2006
User Badges:

Hi,

my service provider added me additional phone numbers to my E1 line (DID).

but they begin with different digits.

My fiest number plan is: 2232195.., SP added me 10 phone nmbers beginig with 2234674.., ho wshould I configure CME to handle it?

Like you can see, some internal numbers starts with 5.. and some with 4.., when calling internaly it is not a problem.

When I have added:

dialplan-pattern 2 2234674.. extension-length 3 extension-pattern 4..

CME stopped to work with my first dialplan-pattern which is:

dialplan-pattern 1 2232195.. extension-length 3 extension-pattern 5..


any suggestions?

regards

Slawek

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 3 (1 ratings)
Loading.
Chris Deren Sun, 10/15/2006 - 12:20
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

Can you please post your configuration?


Chris

slawek_jg Mon, 10/16/2006 - 07:40
User Badges:

Hi,

my config looks like:


voip-incoming translation-rule called 1


translation-rule 1

Rule 1 ^2232195 5

Rule 2 ^2234674 4


translation-rule 11

Rule 1 ^0 00

dial-peer voice 10 pots

incoming called-number 223319...

direct-inward-dial


dial-peer voice 100 pots

destination-pattern 0T

translate-outgoing called 11

port 0/0/0:15


telephony-service

load 7912 P00307020200

max-ephones 48

max-dn 96

ip source-address 10.48.4.1 port 2000

system message CISCO powered by InfoLAN

url services http://10.48.4.2/voiceview/common/login.do

url authentication http://10.48.4.2/voiceview/authentication/authenticate.do

time-format 24

date-format dd-mm-yy

create cnf-files version-stamp 7960 Oct 14 2006 16:45:08

dialplan-pattern 1 2232195.. extension-length 3 extension-pattern 5..

voicemail 2369

max-conferences 8 gain -6

dn-webedit

time-webedit


what to do to make work both dial-plans?


regards

Slawek

Chris Deren Mon, 10/16/2006 - 08:03
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

Well, you have only one inbound pots dial-peer defined (dial-peer 10), which will only match 223319... numbers, in order to match the 2234674.. numbers as well you have couple of options:

1. change dial-peer 10 to the following

dial-peer voice 10 pots

incoming called-number .

direct-inward-dial

port 0/0/0:15

2. Add another dial-peer

dial-peer voice 10 pots

incoming called-number 2234674..

direct-inward-dial

port 0/0/0:15


And add the 2 dialplan pattern under telephony-service.


Also, I'm not sure what the translation rule 1 is for, but it's not applied to anything.


HTH,


Chris



slawek_jg Wed, 10/18/2006 - 09:34
User Badges:

Hi,

I have added another dial-peer

dial-peer voice 11 pots

incoming called-number 2234674..

direct-inward-dial

port 0/0/0:15


in dial-peer voice 10 I have added line:

port 0/0/0:15


then in telephony-service:

dialplan-pattern 2 2234674.. extension-length 3 extension-pattern 4..


After that, my 2nd dialplan is working, 1st is not working :-(

Why?


regards

Slawek

Chris Deren Wed, 10/18/2006 - 12:02
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

What does your "debug isdn q931" show?


What happens if you change the "incoming called number ."


Chris

slawek_jg Thu, 10/19/2006 - 01:21
User Badges:

but when I change to "incoming called-number ." should I also add dialplan-pattern?


Slawek

slawek_jg Thu, 10/19/2006 - 03:47
User Badges:

I have just change (only this) "incoming called-number 2232195.." to "incoming called-number .", now I can dial this numbers (form public), but cannot dial 2234674.. numbers :-(

Do I have to reload CME or sth?


Slawek

Chris Deren Thu, 10/19/2006 - 04:18
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

Can you post your entire config, and "debug isdn q931" for both calls?



Chris Deren Thu, 10/19/2006 - 06:47
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

Slawek,


I looked at your configuration and there are couple of things:


1. The voip-incoming translation-rule 1, is a global translation-rule that will apply to all incoming voip dial-peers, not sure why you need it?


2. I noticed that you have only one ephone-dn, When you perform your testing do you change it back and forth, same with your FXS ports?


Besides the isdn q931 debugs another one to try is "debug voice dialpeer" and "debug voice translation"


Chris

l.mourits Thu, 10/19/2006 - 04:21
User Badges:
  • Silver, 250 points or more

Slawek,


I do not see any voip dialpeers in your config. I have the similar with one of my sites and here is an extract of my config:


dial-peer voice 101 pots

incoming called-number

direct-inward-dial

!

dial-peer voice 102 pots

incoming called-number

direct-inward-dial

!

dial-peer voice 1001 voip

destination-pattern

session protocol sipv2

session target ipv4:

incoming called-number

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 1002 voip

destination-pattern

session protocol sipv2

session target ipv4:

incoming called-number

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

telephony-service

dialplan-pattern 1 extension-length 4

dialplan-pattern 2 extension-length 4


I also had the second DID range come in on another PRI, which is why I also had to add custom cor lists but in your case this is not needed.


Hope it helps,

Leo

Chris Deren Thu, 10/19/2006 - 04:51
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

You do not need any voip dialpeers if the CME is on the same router as the PRIs.


Chris

l.mourits Thu, 10/19/2006 - 06:13
User Badges:
  • Silver, 250 points or more

Chris,


If combined with CUE like Slavek and I do there is a need to create the Voip dialpeers for voice mail to work. You will see this in his config as well:



dial-peer voice 1 voip

translation-profile outgoing 1

destination-pattern 2...

session protocol sipv2

session target ipv4:10.48.4.2

dtmf-relay sip-notify

codec g711ulaw

no vad



All Slawek needs to do IMHO is adding the following:


dial-peer voice 2 voip

translation-profile outgoing 1

destination-pattern 4...

session protocol sipv2

session target ipv4:10.48.4.2

dtmf-relay sip-notify

codec g711ulaw

no vad



Leo

Chris Deren Thu, 10/19/2006 - 06:36
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,
  • Cisco Designated VIP,

    2017 IP Telephony, Contact Center, Unified Communications

Leo,


I appologize for not reading your entire post.

I was only concentrating on his issue which is that calls do not get delivered to the phones.

You are correct that you require the dial-peers to re-direct to CUE.


Chris

l.mourits Thu, 10/19/2006 - 06:49
User Badges:
  • Silver, 250 points or more

Thanks Chris,


Since one typically would test to see if it works by calling the number and see if it hits voicemail I just had to bring the voip dialpeers to the table (been there, done it, had the same problem :-))


Leo



Actions

This Discussion