cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1842
Views
35
Helpful
12
Replies

overhead broadcast / paging system product!!!

jolo07310
Level 5
Level 5

4.13 with bunch of MGCP T1 PRI and FXO voice gateway.

We are going to have overhead broadcast at warehouse.

I have three questions, what is the benefit intergrate with CCM4.13??

And any suggestion about any overhead broadcast product (cost effective, easy to install, configure, easy intergrate with CCM and manage).

What kind of equipments (modules) that I need to intergrate with CCM4.13.

Thanks

Ken

12 Replies 12

dennisleduc
Level 1
Level 1

We use an Andtek solution. (www.andtek.com) in particular the andtek broadcast solution. Although this is typically restricted to an IP phone as the actual paging device. Just a thought.

jpattishall
Level 1
Level 1

I usually use Boegen self amplified speakers, and a Boegen UTI. Then all you need is an FXS card or an ATA. It is the cheapest way to do it if you are looking for overhead paging--if you want to use over the phone too; i agree with the other post or Berbee.

Agreed with the overhead stuff, but if anyone is looking for over the phone paging, Syn-Apps SA-announce is fantastic.

Hi

Does anybody know if the Bogen TAM-B is compatible with Cisco FXS module?

My client has ordered a couple of VIC3-4FXS/DID modules and wants to know if can be used to link the Bogen Paging solution via the TAM-B.

Thanks

Rob Huffman
Hall of Fame
Hall of Fame

Hi Ken,

Here is a little added info to Dennis and Jans good posts;

Good paging tech notes

Using Analog E&M Ports to Interface to Overhead Paging Systems

http://www.cisco.com/warp/public/788/signalling/e_mpaging.html

Verify and Troubleshoot the Cisco IOS MGCP Gateway

http://www.cisco.com/en/US/products/sw/voicesw/ps556/products_tech_note09186a008017b2ad.shtml

The two most popular Overhead paging systems are Valcom and Bogen;

Valcom Paging

http://www.valcompagingproducts.com/?pid=1219&utm_source=GGL&utm_medium=cpc&utm_term=valcom+paging&utm_content=Valcom&utm_campaign=Mfg

Valcom VoIP Paging

http://voip.valcom.com/

Bogen Paging

http://www.bogen.com/

Hope this helps!

Rob

hbarrera2
Level 1
Level 1

I believe if you use an FXS port off of the MGCP gtwy and connect it to your overhead paging amp. Typically the amp will be bogen or viking.

If you use an FXS port you will also need to use a Telephone Access Module (Bogen TAM-B) from each system.

Tommer Catlin
VIP Alumni
VIP Alumni

all suggestions are great. I have also seen.. never have done it.... someone take apart a 7940 and stick it in the ceiling. They wired a speaker to the built in speaker and amplified it to the ceiling mounted speaker. Configured the 7940 using PLAR and whamo.... overhead paging.

enjoy todays hack of the day.

Hey Tommer,

I love that idea, all we need is some barbed wire and duct tape!!

Take care,

Rob

please rate if helpful.

(just jokin)

Did you see the one in the Unity forum? Guy wants the same thing, but for an MWI light in a general area... told him to take the phone apart and re-wire the Msg waiting lamp to a bigger bulb.

Ok guys, a lot of good idea... especially tacatinins' idea.

I am going to rate everyone that put 5 cents here.

Thanks a lot!!

Ken

Guys this is good stuff, I love the creativity and out of box thinking ;-)

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: