×

Warning message

  • Cisco Support Forums is in Read Only mode while the site is being migrated.
  • Cisco Support Forums is in Read Only mode while the site is being migrated.

Cisco 1130 ag - The system is not configured to boot automatically

Answered Question
Nov 7th, 2006
User Badges:

I have a problem on a 1131ag Access point on recycle it stops and makes me maunually type BOOT at the ap: prompt

----------VVVVVVVVVVVVV----------------

ap: Xmodem file system is available.

flashfs[0]: 282 files, 13 directories

flashfs[0]: 0 orphaned files, 0 orphaned directories

flashfs[0]: Total bytes: 15998976

flashfs[0]: Bytes used: 9497088

flashfs[0]: Bytes available: 6501888

flashfs[0]: flashfs fsck took 33 seconds.

Base ethernet MAC Address: 00:12:d9:2b:39:0c

Initializing ethernet port 0...

Reset ethernet port 0...

Reset done!

ethernet link up, 100 mbps, full-duplex

Ethernet port 0 initialized: link is up


The system is not configured to boot automatically. The

following command will finish loading the operating system

software:


boot


C1130 Boot Loader (C1130-BOOT-M) Version 12.3(2)JA, RELEASE SOFTWARE (fc2)

Technical Support: http://www.cisco.com/techsupport

Compiled Mon 08-Nov-04 12:40 by ccai


[I have to type "boot" here to load system]


ap: boot

Loading "flash:/c1130-k9w7-mx.123-7.JA4/c1130-k9w7-mx.123-7.JA4"...#############


File "flash:/c1130-k9w7-mx.123-7.JA4/c1130-k9w7-mx.123-7.JA4" uncompressed and 0

executing...


Restricted Rights Legend


Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.


cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706




Cisco IOS Software, C1130 Software (C1130-K9W7-M), Version 12.3(7)JA4, RELEASE )

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by Cisco Systems, Inc.

Compiled Tue 05-Sep-06 14:14 by alnguyen

Image text-base: 0x00003000, data-base: 0x00683F60


Initializing flashfs...


flashfs[1]: 282 files, 13 directories

flashfs[1]: 0 orphaned files, 0 orphaned directories

flashfs[1]: Total bytes: 15998976

flashfs[1]: Bytes used: 9497088

flashfs[1]: Bytes available: 6501888

flashfs[1]: flashfs fsck took 4 seconds.

flashfs[1]: Initialization complete....done Initializing flashfs.


[Legal notes removed]


cisco AIR-AP1131AG-A-K9 (PowerPCElvis) processor (revision B0) with 24566K/8.

Processor board ID FOC08514JMF

PowerPCElvis CPU at 262Mhz, revision number 0x0950

Last reset from power-on

1 FastEthernet interface

2 802.11 Radio(s)


32K bytes of flash-simulated non-volatile configuration memory.

Base ethernet MAC Address: 00:12:D9:2B:39:0C

Part Number : 73-8962-06

PCA Assembly Number : 800-24818-06

PCA Revision Number : B0

PCB Serial Number : FOC08514JMF

Top Assembly Part Number : 800-25544-01

Top Assembly Serial Number : FTX0909T049

Top Revision Number : A0

Product/Model Number : AIR-AP1131AG-A-K9

-----------^^^^^^^^^^^^------------------


I have already performed the ap: set BOOT etc commands a dozen times with the same results.

It says: The system is not configured to boot automatically.


I've been trying to get this one going for 4 months now..it was knocked out during a power outage while upgrading it.




Correct Answer by m.sir about 10 years 9 months ago

Try command

no boot manual

in global configuration mode

M.

Hope that helps rate if it does

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (5 ratings)
Loading.
Correct Answer
m.sir Wed, 11/08/2006 - 00:17
User Badges:
  • Gold, 750 points or more

Try command

no boot manual

in global configuration mode

M.

Hope that helps rate if it does

glicka Wed, 11/08/2006 - 11:23
User Badges:

I didn't know how to get to global configuration mode - I did manage to get there with a bit of guess work.


You use AP: Boot


Let it go through the boot process then at the AP> prompt, [enable] priviledged command set, type in password.

At AP# prompt type [config] then press enter for [terminal] at AP#[config] type NO BOOT MANUAL press [Enter] key and reboot AP.


Question...Do I have to use a WRITE command to write the configuration to CMOS?


I did just play it safe.

m.sir Wed, 11/08/2006 - 23:03
User Badges:
  • Gold, 750 points or more

Yes you need save settings

AP#write

M.

Hope that helps rate if it does

Brian Hurley Tue, 11/06/2012 - 07:27
User Badges:

What if the AP is in lightweight mode?  It does not let you into global configuration mode, and I cannot find any settings for changing the boot in this mode.   I am hoping this doesn't require reverting the AP back to autonomous just to make that adjustment...

Scott Fella Tue, 11/06/2012 - 09:18
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    The Hall of Fame designation is a lifetime achievement award based on significant overall achievements in the community. 

  • Cisco Designated VIP,

    2017 Wireless

When an ap is lightweight mode, you will not be able to configure that ap.  The WLC will be the one that will manage the ap.  So dedpending on what code is on the WLC, that is the code the AP will download and use.


Thanks,


Scott


Help out other by using the rating system and marking answered questions as "Answered"

Brian Hurley Wed, 11/07/2012 - 08:12
User Badges:

Thanks Scott, I just didnt think the WLC had that as a configurable variable, but I can see that once the AP is connected to a controller those commands start to become available within the CLI on the AP.  It just cannot be adjusted if the lightweight AP has not connected to a controller, but who does that?


Regards,

Brian

Actions

This Discussion