6513 modules not detected ( urgent )

Answered Question
Dec 22nd, 2006
User Badges:

Dear all


I have cisco 6513 switch ( IOS Version 12.2(17d)SXB9 ).i have one ethernet modules installed . i can see this module from CatOS , but i am unable to see ethernet module when i login into MSFC



Router#sh version


Cisco Internetwork Operating System Software


IOS (tm) MSFC2A Software (C6MSFC2A-JK9SV-M), Version 12.2(17d)SXB9, RELEASE SOFTWARE (fc2)


Technical Support: http://www.cisco.com/techsupport


Copyright (c) 1986-2005 by cisco Systems, Inc.


Compiled Thu 21-Jul-05 03:42 by pwade


Image text-base: 0x40008FBC, data-base: 0x425D8000




ROM: System Bootstrap, Version 12.2(17r)SX3, RELEASE SOFTWARE (fc1)


BOOTLDR: MSFC2A Software (C6MSFC2A-JK9SV-M), Version 12.2(17d)SXB9, RELEASE SOFTWARE (fc2)




Router uptime is 1 minute


System returned to ROM by power-on


System image file is "bootflash:c6msfc2a-jk9sv-mz.122-17d.SXB9.bin"






This product contains cryptographic features and is subject to United


States and local country laws governing import, export, transfer and


use. Delivery of Cisco cryptographic products does not imply


third-party authority to import, export, distribute or use encryption.


Importers, exporters, distributors and users are responsible for


compliance with U.S. and local country laws. By using this product you


agree to comply with applicable laws and regulations. If you are unable


to comply with U.S. and local laws, return this product immediately.



A summary of U.S. laws governing Cisco cryptographic products may be found at:


http://www.cisco.com/wwl/export/crypto/tool/stqrg.html



If you require further assistance please contact us by sending email to


[email protected].



cisco MSFC2A (R7000) processor (revision MSFC2A) with 458752K/65536K bytes of memory.


Processor board ID MSFC2A


R7000 CPU at 300Mhz, Implementation 0x27, Rev 3.3, 256KB L2, 1024KB L3 Cache


Last reset from power-on


Bridging software.


X.25 software, Version 3.0.0.


SuperLAT software (copyright 1990 by Meridian Technology Corp).


TN3270 Emulation software.


509K bytes of non-volatile configuration memory.



65536K bytes of Flash internal SIMM (Sector size 512K).


Configuration register is 0x2102


show version , sh run-config unable to show any ethernet module , nor i can see any interface commands related to gigbitethernet


how i can deletect ethernet module in MSFC .


Regards



Correct Answer by ankbhasi about 10 years 8 months ago

Hi Kernel,


Yes you can run your switch in NATIVE IOS mode but currently your switch is running in Hybrid mode and to convert form Hybrid mode to Native mode you have to go through the conversion procedure.


Have a look at this link for more details on Hrbrid mode to Native Mode conversion


http://www.cisco.com/warp/public/473/81.html#conv_msfc_2


HTH


Ankur


*Pls rate all helpfull post

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
ankbhasi Fri, 12/22/2006 - 12:10
User Badges:
  • Cisco Employee,

Hi Kernel,


You are not running a Native IOS on your box and your sup engine is running in HYBRID MODE where there is a CATOS for all layer 2 configuration and interfaces configuration and IOS loaded on MSFC for all routing configuration.


In HYBRID mode you can see all modules only from CATOS and when you access MSFC via session command you are on the IOS on MSFC which can be used to configure all layer 3 coniguration like intervlan routing and other stuffs.


Only when you are running a NATIVE IOS which means a complete one IOS for both supervisor and msfc then from IOS mode you can see all your modules installed and can configure the ethernet interfaces even as layer 3 interfaces which is not possible in HYBRID mode.


So you won;t be able to see any modules from MSFC itself. So you can configure your ethernet module and its interfaces only for layer 2 operation from CATOS and all configurations relating to layer 3 for those vlans should be done on MSFC.


HTH


Ankur


*Pls rate helpfull post


kernel_2431 Fri, 12/22/2006 - 12:28
User Badges:

Thanks a lot for your reply


Can i run the my switch into native IOS mode


Regards


K

Correct Answer
ankbhasi Fri, 12/22/2006 - 12:35
User Badges:
  • Cisco Employee,

Hi Kernel,


Yes you can run your switch in NATIVE IOS mode but currently your switch is running in Hybrid mode and to convert form Hybrid mode to Native mode you have to go through the conversion procedure.


Have a look at this link for more details on Hrbrid mode to Native Mode conversion


http://www.cisco.com/warp/public/473/81.html#conv_msfc_2


HTH


Ankur


*Pls rate all helpfull post

Actions

This Discussion