el 10-02-2013 09:35 AM
Hola!
Tengo una pregunta - duda a ver si me podeis indicar.
Tengo un 1760 32F con un PVDM-256K-4 y una Vic-2fxo. Recientemente he puesto una Vic-2fxs, pero me deja de funcionar la Vic-2fxo.
Lo tengo tal que asi
VIC Slot 2 > Vic-2fxs
VIC Slot 3 > Vic-2fxo
Cuando estan las 2 tarjetas las luces "In use" de la tarjeta VIC Slot 3 se quedan encendidas independientemente de que sea la fxs o la fxo, pero lo que esté en el slot 3 no funciona ni se puede configurar.
En el Show ver del router, si salen las 2 tarjetas, y en el show diag tambien. Pero por ejemplo al hacer conf ter voice-port 3/0 da error
y haciendo un show voice port summary solo sale el puerto 2/0 y 2/1.
Buscando un poco llege a esto:
http://www.cisco.com/en/US/products/hw/routers/ps221/products_tech_note09186a00800c3399.shtml
La cuestion es, necesito otro modulo PVDM para hacer funcionar las 2 tarjetas a la vez?
Gracias,
Un saludo.
Mas datos:
ID MEMORY_REQ TYPE
MainBoard 0X00027A80 1760
0X000F3BB0 public buffer pools
0X00211000 public particle pools
0X0003B100 DSP Buffers
0X0002 0X0000DC00 Card in slot 0
0X002E 0X0001B800 Card in slot 1
0X000E 0X00000000 Card in slot 2
0X000D 0X00000000 Card in slot 3
TOTAL: 0X00390B30
Cisco IOS Software, C1700 Software (C1700-ADVENTERPRISEK9-M), Version 12.4(15)T14, RELEASE SOFTWARE (fc2)
Cisco 1760 (MPC860P) processor (revision 0x500) with 123232K/7840K bytes of memory.
Processor board ID FOC...... (3279806821), with hardware revision 0000
MPC860P processor: part number 5, mask 2
1 FastEthernet interface
1 Serial(sync/async) interface
1 ATM interface
2 Voice FXO interfaces
2 Voice FXS interfaces
32K bytes of NVRAM.
CiscoCallManager#sh voice port summary
IN OUT
PORT CH SIG-TYPE ADMIN OPER STATUS STATUS EC
============== == ============ ===== ==== ======== ======== ==
2/0 -- fxs-ls up dorm on-hook idle y
2/1 -- fxs-ls up dorm on-hook idle y
50/0/1 1 efxs up up on-hook idle y
50/0/1 2 efxs up up on-hook idle y
50/0/2 1 efxs up up on-hook idle y
50/0/2 2 efxs up up on-hook idle y
50/0/3 1 efxs up up on-hook idle y
50/0/3 2 efxs up up on-hook idle y
50/0/4 1 efxs up up on-hook idle y
50/0/4 2 efxs up up on-hook idle y
50/0/5 1 efxs up up on-hook idle y
50/0/5 2 efxs up up on-hook idle y
50/0/6 1 efxs up up on-hook idle y
50/0/6 2 efxs up up on-hook idle y
50/0/7 1 efxs up up on-hook idle y
50/0/7 2 efxs up up on-hook idle y
50/0/8 1 efxs up up on-hook idle y
50/0/8 2 efxs up up on-hook idle y
50/0/9 1 efxs up up on-hook idle y
50/0/9 2 efxs up up on-hook idle y
50/0/10 1 efxs up up on-hook idle y
50/0/10 2 efxs up up on-hook idle y
PWR FAILOVER PORT PSTN FAILOVER PORT
================= ==================
h diag
Slot 0:
C1760 1FE VE 4SLOT DV Mainboard Port adapter, 7 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware Revision : 5.0
Packet Voice DSP Module Slot 0:
Hardware Revision : 3.2
Part Number : 73-6726-01
Board Revision : A0
Deviation Number : 0-0
Fab Version : 03
PCB Serial Number : ICP063300QM
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 02
Number of DSP's : 1
DSP memory size(in kwords): 256
Type of DSP : TMS320C549
Product (FRU) Number : PVDM-256K-4=
VIC Slot 2:
Dual FXS Voice Interface Card
Hardware revision 1.1 Board revision A0
Serial number 0026638578 Part number 800-02493-04
FRU Part Number VIC-2FXS=
Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0E 01 01 01 96 78 F2 50 09 BD 04 00 00 00 00
0x30: 50 00 00 00 01 09 04 01 FF FF FF FF FF FF FF FF
VIC Slot 3:
Dual FXO Voice Interface Card
Hardware revision 1.1 Board revision K0
Serial number 0027405944 Part number 800-02495-01
FRU Part Number VIC-2FXO=
Test history 0x00 RMA number 00-00-00
Connector type WAN Module
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 0D 01 01 01 A2 2E 78 50 09 BF 01 00 00 00 00
0x30: A0 00 00 00 02 02 07 01 FF FF FF FF FF FF FF FF
¡Resuelto! Ir a solución.
el 10-30-2013 10:35 AM
Es correcto tu tarjeta PVDM unicamente tiene 1 dsp, cada tarjeta de dos puertos ya sea 2fxs/2fxo necesita de al menos 1 dsp para poder funcionar a cada una, si le das un show voice dsp active te vas a dar cuenta de los canales que tienes disponibles para hacer funcionar a las tarjetas de voz:
Router#sh voice dsp active | beg Group 0
Group 0:
Current allocated analog signalling channels: 4 ---> Cada DSP tiene capacidad para 2 canales
Current free analog signalling channels: 0
Current allocated digital signalling channels: 0
Current free digital signalling channels: 0
Port(s) served: 2/0 2/1 3/0 3/1 ------------- >> Tarjetas de Voz instaladas
Current Available MIPS: 200
SPMM DSPRM State Image D-sig D-sig A-sig A-sig Mips Voice/Xcode
Dsp Dsp allocate free allocate free Free Chan
1/0 0 UP FIXHC 0 0 2 0 100 0
1/1 1 UP FIXHC 0 0 2 0 100 0
Router#
Cabe mencionar que si quieres implementar una tarjeta digital E1/T1 vas a necesitar de por lo menos una tarjeta PVDM con 3 dsp para que se habilite los canales digitales.
PVDM-256K-4 = 1 dsp = 2 Analog Channels
PVDM-256K-8 = 2 dsp = 4 Analog Channels
PVDM-256K-12 = 3 dsp = 2 Digital Channels + 4 Analog Channels
Espero te sirva en tu esquema!
Saludos
el 10-30-2013 10:35 AM
Es correcto tu tarjeta PVDM unicamente tiene 1 dsp, cada tarjeta de dos puertos ya sea 2fxs/2fxo necesita de al menos 1 dsp para poder funcionar a cada una, si le das un show voice dsp active te vas a dar cuenta de los canales que tienes disponibles para hacer funcionar a las tarjetas de voz:
Router#sh voice dsp active | beg Group 0
Group 0:
Current allocated analog signalling channels: 4 ---> Cada DSP tiene capacidad para 2 canales
Current free analog signalling channels: 0
Current allocated digital signalling channels: 0
Current free digital signalling channels: 0
Port(s) served: 2/0 2/1 3/0 3/1 ------------- >> Tarjetas de Voz instaladas
Current Available MIPS: 200
SPMM DSPRM State Image D-sig D-sig A-sig A-sig Mips Voice/Xcode
Dsp Dsp allocate free allocate free Free Chan
1/0 0 UP FIXHC 0 0 2 0 100 0
1/1 1 UP FIXHC 0 0 2 0 100 0
Router#
Cabe mencionar que si quieres implementar una tarjeta digital E1/T1 vas a necesitar de por lo menos una tarjeta PVDM con 3 dsp para que se habilite los canales digitales.
PVDM-256K-4 = 1 dsp = 2 Analog Channels
PVDM-256K-8 = 2 dsp = 4 Analog Channels
PVDM-256K-12 = 3 dsp = 2 Digital Channels + 4 Analog Channels
Espero te sirva en tu esquema!
Saludos
el 11-02-2013 01:52 PM
Me lo imaginaba!
Probare el comando que indicas a ver que sale.
no solo voy a poner como mucho los 2 puertos fxo y uno fxs
Muchas gracias!!!
el 11-21-2013 01:54 PM
Hola,
Es correcto lo que dices:
CiscoCallManager#sh voice dsp active | beg Group 0
Group 0:
Current allocated analog signalling channels: 2
Current free analog signalling channels: 0
Current allocated digital signalling channels: 0
Current free digital signalling channels: 0
Port(s) served: 3/0 3/1
Current Available MIPS: 100
SPMM DSPRM State Image D-sig D-sig A-sig A-sig Mips Voice/Xcode
Dsp Dsp allocate free allocate free Free Chan
0/0 0 UP FIXHC 0 0 2 0 100
Intentare conseguir otra PVDM-256K-4 o la de 8. Gracias nuevamente
¡Conecte con otros expertos de Cisco y del mundo! Encuentre soluciones a sus problemas técnicos o comerciales, y aprenda compartiendo experiencias.
Queremos que su experiencia sea grata, le compartimos algunos links que le ayudarán a familiarizarse con la Comunidad de Cisco:
Navegue y encuentre contenido personalizado de la comunidad