FI 6324 の交換時、 Firmware の不一致を検知した場合には、Peer の FI の Firmware と同期させることにより、既存 FI クラスタへ組み込むことが可能です。
サンプル出力:
3.0(1e) クラスタのFI交換に、 3.0(1c) しかインストールされていない FI 6324 を使用。
---- Basic System Configuration Dialog ----
This setup utility will guide you through the basic configuration of
the system. Only minimal configuration including IP connectivity to
the Fabric interconnect and its clustering mode is performed through these steps.
Type Ctrl-C at any time to abort configuration and reboot system.
To back track or make modifications to already entered values,
complete input till end of section and answer no when prompted
to apply configuration.
Enter the configuration method. (console/gui) ? console
Installer has detected the presence of a peer Fabric interconnect. This Fabric interconnect will be added to the cluster. Continue (y/n) ? y
Enter the admin password of the peer Fabric interconnect:
Connecting to peer Fabric interconnect... done
Retrieving config from peer Fabric interconnect... done
Installer has determined that the peer Fabric Interconnect is running a different firmware version than the local Fabric. Cannot join cluster.
Local Fabric Interconnect
UCSM version : 3.0(1c)
Kernel version : 5.0(3)N2(3.01c)
System version : 5.0(3)N2(3.01c)
local_model_no : Mini
Peer Fabric Interconnect
UCSM version : 3.0(1e)
Kernel version : 5.0(3)N2(3.01e)
System version : 5.0(3)N2(3.01e)
peer_model_no : Mini
Do you wish to update firmware on this Fabric Interconnect to the Peer's version? (y/n): y
Updating firmware of Fabric Interconnect....... [ Please don't press Ctrl+c while updating firmware ]
Updating images
Please wait for firmware update to complete....
Checking the Compatibility of new Firmware..... [ Please don't Press ctrl+c ].
Verifying image bootflash:/installables/switch/ucs-mini-k9-kickstart.5.0.3.N2.3.01e.bin for boot variable "kickstart".
[####################] 100% -- SUCCESS
Verifying image bootflash:/installables/switch/ucs-mini-k9-system.5.0.3.N2.3.01e.bin for boot variable "system".
[####################] 100% -- SUCCESS
Verifying image type.
[####################] 100% -- SUCCESS
Extracting "system" version from image bootflash:/installables/switch/ucs-mini-k9-system.5.0.3.N2.3.01e.bin.
[####################] 100% -- SUCCESS
Extracting "kickstart" version from image bootflash:/installables/switch/ucs-mini-k9-kickstart.5.0.3.N2.3.01e.bin.
[####################] 100% -- SUCCESS
Extracting "bios" version from image bootflash:/installables/switch/ucs-mini-k9-system.5.0.3.N2.3.01e.bin.
[####################] 100% -- SUCCESS
Performing module support checks.
[####################] 100% -- SUCCESS
Notifying services about system upgrade.
[####################] 100% -- SUCCESS
Compatibility check is done:
Module bootable Impact Install-type Reason
------ -------- -------------- ------------ ------
1 yes disruptive reset Incompatible image
Images will be upgraded according to following table:
Module Image Running-Version New-Version Upg-Required
------ ---------------- ---------------------- ---------------------- ------------
1 system 5.0(3)N2(3.01c) 5.0(3)N2(3.01e) yes
1 kickstart 5.0(3)N2(3.01c) 5.0(3)N2(3.01e) yes
1 bios v1.022.0 v1.022.0 no
1 power-seq v1.0 v1.0 no
Switch will be reloaded for disruptive upgrade.
Install is in progress, please wait.
Performing runtime checks.
[####################] 100% -- SUCCESS
Setting boot variables.
[####################] 100% -- SUCCESS
Performing configuration copy.
[####################] 100% -- SUCCESS
Install has been successful.
Firmware Updation Successfully Completed. Please wait to enter the IP address
Peer Fabric interconnect Mgmt0 IPv4 Address: X.X.X.X
Peer Fabric interconnect Mgmt0 IPv4 Netmask: x.x.x.x
Cluster IPv4 address : Y.Y.Y.Y
Peer FI is IPv4 Cluster enabled. Please Provide Local Fabric Interconnect Mgmt0 IPv4 Address
Physical Switch Mgmt0 IP address : Z.Z.Z.Z
Apply and save the configuration (select 'no' if you want to re-enter)? (yes/no): yes
Applying configuration. Please wait.
Configuration file - Ok
FI will now reboot after which you can access the switch.