find the configuration below

interface Vlan199
 ip address 192.168.3.251 255.255.255.0
 ip access-group 101 in
 ip access-group 103 out
 

interface Vlan200
  ip address 192.168.2.251 255.255.255.0
 ip access-group 102 in
 ip access-group 104 out

interface Vlan2
 ip address 10.2.1.251 255.255.255.0

interface vlan5
 ip address 10.2.9.251 255.255.255.0

interface vlan6
 ip address 10.2.10.251 255.255.255.0

i have put an access list

access-list 101 permit ip 192.168.3.0 0.0.0.255 10.2.9.0 0.0.0.255
access-list 101 permit ip 192.168.3.0 0.0.0.255 10.2.1.0 0.0.0.255
access-list 101 permit ip 192.168.3.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 101 permit ip 192.168.3.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 101 permit ip 192.168.3.0 0.0.0.255 192.168.16.0 0.0.0.255
access-list 102 permit ip 192.168.2.0 0.0.0.255 10.2.9.0 0.0.0.255
access-list 102 permit ip 192.168.2.0 0.0.0.255 10.2.1.0 0.0.0.255
access-list 102 permit ip 192.168.2.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 102 permit ip 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 102 permit ip 192.168.2.0 0.0.0.255 192.168.16.0 0.0.0.255
access-list 103 permit ip 10.2.9.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 103 permit ip 10.2.1.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 103 permit ip 192.168.3.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 103 permit ip 192.168.2.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 103 permit ip 192.168.16.0 0.0.0.255 192.168.3.0 0.0.0.255
access-list 104 permit ip 10.2.9.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 104 permit ip 10.2.1.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 104 permit ip 192.168.2.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 104 permit ip 192.168.3.0 0.0.0.255 192.168.2.0 0.0.0.255
access-list 104 permit ip 192.168.16.0 0.0.0.255 192.168.2.0 0.0.0.255


now except vlan6, all the remaining vlan's can able to speak to vlan199 & vlan200, 192.168.16.x is residing on the otherside of the vlan6. i.e 1 NIC ip is 10.2.10.1/24 & other NIC is 192.168.16.1/24, 192.168.16.1 is connected to 192.168.16.2 via cross cable, i made 192.168.16.1 as router(linux), i had put "ip route 192.168.16.0 255.255.255.0 10.2.10.1" on the switch, actually 192.168.6.2 machine should ping others networks also(valn199,200,2,5), but it is not pining, also it is not pinging vice versa, what could be the problem, is my access-list is correct or do i need to make changes in that? this is very urgent as i failed on my 1st attempt.