Barnstable-IPC-ADSL#sh logging Syslog logging: enabled (1 messages dropped, 1 messages rate-limited, 0 flushes, 0 overruns, xml disabled, filtering disabled) Console logging: level debugging, 1940 messages logged, xml disabled, filtering disabled Monitor logging: level debugging, 629 messages logged, xml disabled, filtering disabled Buffer logging: level debugging, 209 messages logged, xml disabled, filtering disabled Logging Exception size (4096 bytes) Count and timestamp logging messages: disabled No active filter modules. Trap logging: level informational, 1089 message lines logged Log Buffer (32768 bytes): Nov 17 15:56:05.009: %SYS-5-CONFIG_I: Configured from console by vty0 (10.10.0.24) Nov 17 17:59:43.617: DSL: Defect: LOS LOF LCDf LOM: retraining Nov 17 17:59:43.617: DSL: Received response: 0x41 Nov 17 17:59:44.769: Resetting ATM0 Nov 17 17:59:46.117: DSL: SM: [DMTDSL_SHOWTIME -> DMTDSL_RE_OPEN] Nov 17 17:59:46.117: DSL: Send ADSL_CLOSE command. Nov 17 17:59:46.117: DSL: Sent command 0x4 Nov 17 17:59:46.517: %LINK-3-UPDOWN: Interface ATM0, changed state to down Nov 17 17:59:46.641: DSL: Received response: 0x25 Nov 17 17:59:46.641: DSL: Connection closed Nov 17 17:59:46.649: DSL: SM: [DMTDSL_RE_OPEN -> DMTDSL_DO_OPEN] Nov 17 17:59:46.649: DSL: Trying to bring up DSL line using Embedded firmware version : 3.9.220 Nov 17 17:59:46.649: DSL: Send ADSL_OPEN command. Nov 17 17:59:46.649: DSL: Using subfunction 0x15 Nov 17 17:59:46.649: DSL: Using subfunction 0x15 Nov 17 17:59:46.649: LOCAL:Max noise margin for power cutoff 31 Nov 17 17:59:46.649: DSL: Sent command 0x3 Nov 17 17:59:47.517: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down Nov 17 17:59:49.153: DSL: 1: Modem state = 0x8 Nov 17 17:59:51.653: DSL: 2: Modem state = 0x10 Nov 17 17:59:54.153: DSL: 3: Modem state = 0x10 Nov 17 17:59:56.653: DSL: 4: Modem state = 0x10 Nov 17 17:59:59.153: DSL: 5: Modem state = 0x10 Nov 17 18:00:00.285: DSL: Received response: 0x24 Nov 17 18:00:00.285: DSL: DSL line trained using Embedded firmware version : 3.9.220 Nov 17 18:00:00.285: DSL: Showtime! Nov 17 18:00:00.285: DSL: Sent command 0x11 Nov 17 18:00:00.289: DSL: Received response: 0x61 Nov 17 18:00:00.289: DSL: Read firmware revision 0x1A04 Nov 17 18:00:00.289: DSL: Sent command 0x31 Nov 17 18:00:00.297: DSL: Received response: 0x12 Nov 17 18:00:00.297: DSL: operation mode 0x0002 Nov 17 18:00:00.297: DSL: Sent command 0x33 Nov 17 18:00:00.301: DSL: Received response: 0x16 Nov 17 18:00:00.301: DSL: Far End ITU Country Code 0xB5 Nov 17 18:00:00.301: DSL: Far End ITU Vendor ID TSTC Nov 17 18:00:00.301: DSL: Far End ITU Vendor ID Specific 0x0400 Nov 17 18:00:00.301: DSL: Far End ITU Vendor STD Number 0x0001 Nov 17 18:00:00.301: DSL: Sent command 0x32 Nov 17 18:00:00.305: DSL: Received response: 0x14 Nov 17 18:00:00.305: DSL: Near End ITU Country Code 0x00 Nov 17 18:00:00.305: DSL: Near End ITU Vendor ID ALCB Nov 17 18:00:00.305: DSL: Near End ITU Vendor ID Specific 0x0000 Nov 17 18:00:00.309: DSL: Near End ITU Vendor STD Number 0x0001 Nov 17 18:00:00.309: DSL: SM: [DMTDSL_DO_OPEN -> DMTDSL_SHOWTIME] Nov 17 18:00:00.769: Resetting ATM0 Nov 17 18:00:01.021: ATM interface(ATM0.1): CPCS encaps failure, VCD# 1 Nov 17 18:00:02.517: %LINK-3-UPDOWN: Interface ATM0, changed state to up Nov 17 18:00:03.517: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up Nov 17 18:47:33.081: DSL: Defect: LOS LOF LCDf LOM: retraining Nov 17 18:47:33.081: DSL: Received response: 0x41 Nov 17 18:47:33.769: Resetting ATM0 Nov 17 18:47:35.517: %LINK-3-UPDOWN: Interface ATM0, changed state to down Nov 17 18:47:35.581: DSL: SM: [DMTDSL_SHOWTIME -> DMTDSL_RE_OPEN] Nov 17 18:47:35.581: DSL: Send ADSL_CLOSE command. Nov 17 18:47:35.581: DSL: Sent command 0x4 Nov 17 18:47:36.105: DSL: Received response: 0x25 Nov 17 18:47:36.105: DSL: Connection closed Nov 17 18:47:36.113: DSL: SM: [DMTDSL_RE_OPEN -> DMTDSL_DO_OPEN] Nov 17 18:47:36.113: DSL: Trying to bring up DSL line using Embedded firmware version : 3.9.220 Nov 17 18:47:36.117: DSL: Send ADSL_OPEN command. Nov 17 18:47:36.117: DSL: Using subfunction 0x15 Nov 17 18:47:36.117: DSL: Using subfunction 0x15 Nov 17 18:47:36.117: LOCAL:Max noise margin for power cutoff 31 Nov 17 18:47:36.117: DSL: Sent command 0x3 Nov 17 18:47:36.517: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down Nov 17 18:47:38.617: DSL: 1: Modem state = 0x8 Nov 17 18:47:41.117: DSL: 2: Modem state = 0x10 Nov 17 18:47:43.617: DSL: 3: Modem state = 0x10 Nov 17 18:47:46.117: DSL: 4: Modem state = 0x10 Nov 17 18:47:47.853: DSL: Received response: 0x24 Nov 17 18:47:47.853: DSL: DSL line trained using Embedded firmware version : 3.9.220 Nov 17 18:47:47.853: DSL: Showtime! Nov 17 18:47:47.857: DSL: Sent command 0x11 Nov 17 18:47:47.857: DSL: Received response: 0x61 Nov 17 18:47:47.857: DSL: Read firmware revision 0x1A04 Nov 17 18:47:47.861: DSL: Sent command 0x31 Nov 17 18:47:47.865: DSL: Received response: 0x12 Nov 17 18:47:47.865: DSL: operation mode 0x0002 Nov 17 18:47:47.865: DSL: Sent command 0x33 Nov 17 18:47:47.869: DSL: Received response: 0x16 Nov 17 18:47:47.869: DSL: Far End ITU Country Code 0xB5 Nov 17 18:47:47.869: DSL: Far End ITU Vendor ID TSTC Nov 17 18:47:47.869: DSL: Far End ITU Vendor ID Specific 0x0400 Nov 17 18:47:47.869: DSL: Far End ITU Vendor STD Number 0x0001 Nov 17 18:47:47.869: DSL: Sent command 0x32 Nov 17 18:47:47.873: DSL: Received response: 0x14 Nov 17 18:47:47.873: DSL: Near End ITU Country Code 0x00 Nov 17 18:47:47.873: DSL: Near End ITU Vendor ID ALCB Nov 17 18:47:47.877: DSL: Near End ITU Vendor ID Specific 0x0000 Nov 17 18:47:47.877: DSL: Near End ITU Vendor STD Number 0x0001 Nov 17 18:47:47.877: DSL: SM: [DMTDSL_DO_OPEN -> DMTDSL_SHOWTIME] Nov 17 18:47:48.553: Resetting ATM0 Nov 17 18:47:48.809: ATM interface(ATM0.1): CPCS encaps failure, VCD# 1 Nov 17 18:47:50.301: %LINK-3-UPDOWN: Interface ATM0, changed state to up Nov 17 18:47:51.301: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up Nov 18 00:30:07.351: DSL: Defect: LOS LOF LCDf: retraining Nov 18 00:30:07.351: DSL: Received response: 0x41 Nov 18 00:30:07.767: Resetting ATM0 Nov 18 00:30:09.515: %LINK-3-UPDOWN: Interface ATM0, changed state to down Nov 18 00:30:09.851: DSL: SM: [DMTDSL_SHOWTIME -> DMTDSL_RE_OPEN] Nov 18 00:30:09.851: DSL: Send ADSL_CLOSE command. Nov 18 00:30:09.851: DSL: Sent command 0x4 Nov 18 00:30:10.371: DSL: Received response: 0x25 Nov 18 00:30:10.371: DSL: Connection closed Nov 18 00:30:10.383: DSL: SM: [DMTDSL_RE_OPEN -> DMTDSL_DO_OPEN] Nov 18 00:30:10.383: DSL: Trying to bring up DSL line using Embedded firmware version : 3.9.220 Nov 18 00:30:10.383: DSL: Send ADSL_OPEN command. Nov 18 00:30:10.383: DSL: Using subfunction 0x15 Nov 18 00:30:10.383: DSL: Using subfunction 0x15 Nov 18 00:30:10.383: LOCAL:Max noise margin for power cutoff 31 Nov 18 00:30:10.383: DSL: Sent command 0x3 Nov 18 00:30:10.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down Nov 18 00:30:12.883: DSL: 1: Modem state = 0x8 Nov 18 00:30:15.383: DSL: 2: Modem state = 0x10 Nov 18 00:30:17.887: DSL: 3: Modem state = 0x10 Nov 18 00:30:20.387: DSL: 4: Modem state = 0x10 Nov 18 00:30:21.903: DSL: Received response: 0x24 Nov 18 00:30:21.903: DSL: DSL line trained using Embedded firmware version : 3.9.220 Nov 18 00:30:21.903: DSL: Showtime! Nov 18 00:30:21.907: DSL: Sent command 0x11 Nov 18 00:30:21.907: DSL: Received response: 0x61 Nov 18 00:30:21.911: DSL: Read firmware revision 0x1A04 Nov 18 00:30:21.911: DSL: Sent command 0x31 Nov 18 00:30:21.915: DSL: Received response: 0x12 Nov 18 00:30:21.915: DSL: operation mode 0x0002 Nov 18 00:30:21.915: DSL: Sent command 0x33 Nov 18 00:30:21.919: DSL: Received response: 0x16 Nov 18 00:30:21.919: DSL: Far End ITU Country Code 0xB5 Nov 18 00:30:21.919: DSL: Far End ITU Vendor ID TSTC Nov 18 00:30:21.919: DSL: Far End ITU Vendor ID Specific 0x0400 Nov 18 00:30:21.919: DSL: Far End ITU Vendor STD Number 0x0001 Nov 18 00:30:21.923: DSL: Sent command 0x32 Nov 18 00:30:21.923: DSL: Received response: 0x14 Nov 18 00:30:21.923: DSL: Near End ITU Country Code 0x00 Nov 18 00:30:21.923: DSL: Near End ITU Vendor ID ALCB Nov 18 00:30:21.927: DSL: Near End ITU Vendor ID Specific 0x0000 Nov 18 00:30:21.927: DSL: Near End ITU Vendor STD Number 0x0001 Nov 18 00:30:21.927: DSL: SM: [DMTDSL_DO_OPEN -> DMTDSL_SHOWTIME] Nov 18 00:30:22.767: Resetting ATM0 Nov 18 00:30:23.019: ATM interface(ATM0.1): CPCS encaps failure, VCD# 1 Nov 18 00:30:24.515: %LINK-3-UPDOWN: Interface ATM0, changed state to up Nov 18 00:30:25.515: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up Nov 18 05:56:43.886: DSL: Defect: LOS LOF LCDf LOM: retraining Nov 18 05:56:43.886: DSL: Received response: 0x41 Nov 18 05:56:44.766: Resetting ATM0 Nov 18 05:56:46.386: DSL: SM: [DMTDSL_SHOWTIME -> DMTDSL_RE_OPEN] Nov 18 05:56:46.386: DSL: Send ADSL_CLOSE command. Nov 18 05:56:46.386: DSL: Sent command 0x4 Nov 18 05:56:46.514: %LINK-3-UPDOWN: Interface ATM0, changed state to down Nov 18 05:56:46.910: DSL: Received response: 0x25 Nov 18 05:56:46.910: DSL: Connection closed Nov 18 05:56:46.922: DSL: SM: [DMTDSL_RE_OPEN -> DMTDSL_DO_OPEN] Nov 18 05:56:46.922: DSL: Trying to bring up DSL line using Embedded firmware version : 3.9.220 Nov 18 05:56:46.922: DSL: Send ADSL_OPEN command. Nov 18 05:56:46.922: DSL: Using subfunction 0x15 Nov 18 05:56:46.922: DSL: Using subfunction 0x15 Nov 18 05:56:46.922: LOCAL:Max noise margin for power cutoff 31 Nov 18 05:56:46.922: DSL: Sent command 0x3 Nov 18 05:56:47.514: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down Nov 18 05:56:49.422: DSL: 1: Modem state = 0x8 Nov 18 05:56:51.922: DSL: 2: Modem state = 0x10 Nov 18 05:56:54.422: DSL: 3: Modem state = 0x10 Nov 18 05:56:56.922: DSL: 4: Modem state = 0x10 Nov 18 05:56:58.782: DSL: Received response: 0x24 Nov 18 05:56:58.782: DSL: DSL line trained using Embedded firmware version : 3.9.220 Nov 18 05:56:58.782: DSL: Showtime! Nov 18 05:56:58.782: DSL: Sent command 0x11 Nov 18 05:56:58.786: DSL: Received response: 0x61 Nov 18 05:56:58.786: DSL: Read firmware revision 0x1A04 Nov 18 05:56:58.786: DSL: Sent command 0x31 Nov 18 05:56:58.794: DSL: Received response: 0x12 Nov 18 05:56:58.794: DSL: operation mode 0x0002 Nov 18 05:56:58.794: DSL: Sent command 0x33 Nov 18 05:56:58.798: DSL: Received response: 0x16 Nov 18 05:56:58.798: DSL: Far End ITU Country Code 0xB5 Nov 18 05:56:58.798: DSL: Far End ITU Vendor ID TSTC Nov 18 05:56:58.798: DSL: Far End ITU Vendor ID Specific 0x0400 Nov 18 05:56:58.798: DSL: Far End ITU Vendor STD Number 0x0001 Nov 18 05:56:58.798: DSL: Sent command 0x32 Nov 18 05:56:58.806: DSL: Received response: 0x14 Nov 18 05:56:58.806: DSL: Near End ITU Country Code 0x00 Nov 18 05:56:58.806: DSL: Near End ITU Vendor ID ALCB Nov 18 05:56:58.806: DSL: Near End ITU Vendor ID Specific 0x0000 Nov 18 05:56:58.806: DSL: Near End ITU Vendor STD Number 0x0001 Nov 18 05:56:58.806: DSL: SM: [DMTDSL_DO_OPEN -> DMTDSL_SHOWTIME] Nov 18 05:56:59.378: Resetting ATM0 Nov 18 05:56:59.634: ATM interface(ATM0.1): CPCS encaps failure, VCD# 1 Nov 18 05:57:01.126: %LINK-3-UPDOWN: Interface ATM0, changed state to up Nov 18 05:57:02.126: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to up Barnstable-IPC-ADSL# sh dsl int atm 0 ATU-R (DS) ATU-C (US) Modem Status: Showtime (DMTDSL_SHOWTIME) DSL Mode: ITU G.992.1 (G.DMT) ITU STD NUM: 0x01 0x01 Vendor ID: 'ALCB' 'TSTC' Vendor Specific: 0x0000 0x0400 Vendor Country: 0x00 0xB5 Capacity Used: 21% 38% Noise Margin: 31.0 dB 24.0 dB Output Power: 20.0 dBm 12.0 dBm Attenuation: 47.0 dB 27.0 dB Defect Status: None None Last Fail Code: Message error Selftest Result: 0x00 Subfunction: 0x15 Interrupts: 3766 (3 spurious) Activations: 263 Init FW: embedded Operartion FW: embedded SW Version: 3.9.220 FW Version: 0x1A04 Interleave Fast Interleave Fast Speed (kbps): 0 1152 0 288 Reed-Solomon EC: 0 0 0 0 CRC Errors: 0 4 0 0 Header Errors: 0 1 0 0 Bit Errors: 0 0 BER Valid sec: 0 0 BER Invalid sec: 0 0 LOM Monitoring : Disabled DMT Bits Per Bin 00: 0 0 0 0 0 0 0 0 0 2 3 4 5 5 5 5 10: 6 6 6 5 6 6 6 5 5 4 3 2 3 3 0 0 20: 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 30: 3 4 4 4 4 4 5 5 5 5 5 5 5 5 5 5 40: 0 5 5 5 5 5 2 5 5 4 4 5 4 4 4 4 50: 4 4 2 0 4 4 4 5 5 5 5 4 5 4 5 4 60: 4 4 4 4 4 4 4 4 4 4 4 4 4 3 2 3 70: 4 4 4 4 4 4 3 3 3 3 2 2 0 0 2 2 80: 2 2 2 2 2 2 2 2 2 2 2 0 2 2 2 2 90: 2 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 A0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Training log buffer capability is not enabled yet. Barnstable-IPC-ADSL#sh ver Cisco IOS Software, C837 Software (C837-K9O3Y6-M), Version 12.4(5b), RELEASE SOFTWARE (fc2) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2006 by Cisco Systems, Inc. Compiled Wed 19-Apr-06 05:59 by ssearch ROM: System Bootstrap, Version 12.2(11r)YV5, RELEASE SOFTWARE (fc1) Barnstable-IPC-ADSL uptime is 2 weeks, 6 days, 23 hours, 18 minutes System returned to ROM by power-on System restarted at 10:27:00 UTC Tue Oct 28 2008 System image file is "flash:c837-k9o3y6-mz.124-5b.bin" This product contains cryptographic features and is subject to United States and local country laws governing import, export, transfer and use. Delivery of Cisco cryptographic products does not imply third-party authority to import, export, distribute or use encryption. Importers, exporters, distributors and users are responsible for compliance with U.S. and local country laws. By using this product you agree to comply with applicable laws and regulations. If you are unable to comply with U.S. and local laws, return this product immediately. A summary of U.S. laws governing Cisco cryptographic products may be found at: http://www.cisco.com/wwl/export/crypto/tool/stqrg.html If you require further assistance please contact us by sending email to export@cisco.com. Cisco C837 (MPC857DSL) processor (revision 0x600) with 58983K/6553K bytes of memory. Processor board ID FCZ102412FM (1958642958), with hardware revision 0000 CPU rev number 7 2 Ethernet interfaces 4 FastEthernet interfaces 1 ATM interface 128K bytes of NVRAM. 12288K bytes of processor board System flash (Read/Write) 2048K bytes of processor board Web flash (Read/Write) Configuration register is 0x2102