R2_2081249#ping 172.16.10.1 *Dec 7 13:48:43.995: As1 DDR: rotor dialout [best] *Dec 7 13:48:43.995: As1 DDR: Dialing cause ip (s=172.16.11.2, d=172.16.10.2) *Dec 7 13:48:43.995: As1 DDR: Attempting to dial 4960537 *Dec 7 13:48:43.995: CHAT1: Attempting async line dialer script *Dec 7 13:48:43.995: CHAT1: Dialing using Modem script: dialout & System script: none *Dec 7 13:48:43.999: CHAT1: process started *Dec 7 13:48:43.999: CHAT1: Asserting DTR *Dec 7 13:48:43.999: CHAT1: Chat script dialout started *Dec 7 13:48:43.999: CHAT1: Sending string: AT *Dec 7 13:48:43.999: CHAT1: Expecting string: OK *Dec 7 13:48:43.999: CHAT1: Completed match for expect: OK *Dec 7 13:48:43.999: CHAT1: Sending string: ATDT \T<4960537> *Dec 7 13:48:43.999: CHAT1: Expecting string: CONNECT *Dec 7 13:48:48.999: CHAT1: Timeout expecting: CONNECT *Dec 7 13:48:48.999: CHAT1: Chat script dialout finished, status = Connection timed out; remote host not responding *Dec 7 13:48:48.999: TTY1: Line reset by "Async dialer" *Dec 7 13:48:48.999: As1 DDR: disconnecting call *Dec 7 13:48:48.999: TTY1: Modem: (unknown)->HANGUP *Dec 7 13:48:48.999: TTY1: no timer type 0 to destroy *Dec 7 13:48:48.999: TTY1: no timer type 1 to destroy *Dec 7 13:48:48.999: TTY1: no timer type 3 to destroy *Dec 7 13:48:48.999: TTY1: no timer type 4 to destroy *Dec 7 13:48:48.999: TTY1: no timer type 10 to destroy *Dec 7 13:48:48.999: TTY1: no timer type 2 to destroy *Dec 7 13:48:49.123: Di1: No free dialer - starting fast idle timer *Dec 7 13:48:49.219: TTY1: dropping DTR, hanging up *Dec 7 13:48:49.219: tty1: Modem: HANGUP->IDLE *Dec 7 13:48:50.219: TTY1: restoring DTR *Dec 7 13:48:50.219: TTY1: autoconfigure probe started *Dec 7 13:48:54.623: Di1: No free dialer - starting fast idle timer *Dec 7 13:49:00.123: Di1: No free dialer - starting fast idle timer *Dec 7 13:49:03.999: As1 DDR: re-enable timeout *Dec 7 13:49:03.999: DDR: Dialing failed, 1 packets unqueued and discarded *Dec 7 13:49:05.623: As1 DDR: rotor dialout [best] least recent failure is also most recent failure *Dec 7 13:49:05.623: As1 DDR: rotor dialout [best] also has most recent failure *Dec 7 13:49:05.623: As1 DDR: rotor dialout [best] *Dec 7 13:49:05.623: As1 DDR: Dialing cause ip (s=172.16.11.2, d=172.16.10.1) *Dec 7 13:49:05.623: As1 DDR: Attempting to dial 4960537 *Dec 7 13:49:05.623: CHAT1: Attempting async line dialer script *Dec 7 13:49:05.623: CHAT1: Dialing using Modem script: dialout & System script: none *Dec 7 13:49:05.623: CHAT1: process started *Dec 7 13:49:05.623: CHAT1: Asserting DTR *Dec 7 13:49:05.623: CHAT1: Chat script dialout started *Dec 7 13:49:05.623: CHAT1: Sending string: AT *Dec 7 13:49:05.623: CHAT1: Expecting string: OK *Dec 7 13:49:05.623: CHAT1: Completed match for expect: OK *Dec 7 13:49:05.623: CHAT1: Sending string: ATDT \T<4960537> *Dec 7 13:49:05.623: CHAT1: Expecting string: CONNECT *Dec 7 13:49:05.623: CHAT1: Timeout expecting: CONNECT *Dec 7 13:49:10.623: CHAT1: Chat script dialout finished, status = Connection timed out; remote host not responding *Dec 7 13:49:10.623: TTY1: Line reset by "Async dialer" *Dec 7 13:49:10.623: As1 DDR: disconnecting call *Dec 7 13:49:10.623: TTY1: Modem: (unknown)->HANGUP *Dec 7 13:49:10.623: TTY1: no timer type 0 to destroy *Dec 7 13:49:10.623: TTY1: no timer type 1 to destroy *Dec 7 13:49:10.623: TTY1: no timer type 3 to destroy *Dec 7 13:49:10.623: TTY1: no timer type 4 to destroy *Dec 7 13:49:10.623: TTY1: no timer type 10 to destroy *Dec 7 13:49:10.623: TTY1: no timer type 2 to destroy *Dec 7 13:49:11.123: Di1: No free dialer - starting fast idle timer *Dec 7 13:49:11.219: TTY1: dropping DTR, hanging up *Dec 7 13:49:11.219: tty1: Modem: HANGUP->IDLE *Dec 7 13:49:12.219: TTY1: restoring DTR *Dec 7 13:49:12.219: TTY1: autoconfigure probe started R2_2081249#sh modem 0/0 Mdm Typ Status Tx/Rx G Duration TX RX RTS CTS DSR DCD DTR 0/0 Idle / 0 00:00:00 - - x x x x Modem 0/0 [line 1], Async1, TTY1 WIC-AM firmware 18F Modem config: Incoming and Outgoing Protocol: , Compression: Last clearing of "show modem" counters: never 0 incoming complete 0 incoming failures 0 outgoing complete 0 outgoing failure R2_2081249#sh line Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int * 0 CTY - - - - - 1 0 0/0 - Ready I 1 TTY - inout - - - 1 0 0/0 - Idle 5 AUX 9600/9600 - - - - - 0 0 0/0 - Ready 6 VTY - - - - - 0 0 0/0 - Idle 7 VTY - - - - - 0 0 0/0 - Idle 8 VTY - - - - - 0 0 0/0 - Idle 9 VTY - - - - - 0 0 0/0 - Idle 10 VTY - - - - - 0 0 0/0 - Idle Line(s) not in async mode -or- with no hardware support: 2-4 R2_2081249#sh ip int b Interface IP-Address OK? Method Status Protocol FastEthernet0 172.16.11.1 YES NVRAM up up FastEthernet1 192.168.11.1 YES NVRAM up down FastEthernet2 unassigned YES unset up down FastEthernet3 unassigned YES unset up down FastEthernet4 unassigned YES unset up down FastEthernet5 unassigned YES unset up down FastEthernet6 unassigned YES unset up down FastEthernet7 unassigned YES unset up down FastEthernet8 unassigned YES unset up down FastEthernet9 unassigned YES unset up down Vlan1 unassigned YES NVRAM up down Async1 unassigned YES NVRAM down down Dialer1 unassigned YES NVRAM up up R2_2081249#debug confmodem Modem Configuration Database debugging is on R2_2081249(config-line)#modem autoconfigure discovery R2_2081249(config-line)#^Z R2_2081249# R2_2081249# *Dec 6 14:58:26.039: %SYS-5-CONFIG_I: Configured from console by console *Dec 6 14:58:32.191: TTY1: Modem type is default *Dec 6 14:58:32.191: TTY1: Modem command: --AT&F&C1&D2S0=1H0-- *Dec 6 14:58:32.723: TTY1: Modem configuration succeeded *Dec 6 14:58:32.723: TTY1: Done with modem configuration R2_2081249# R2_2081249(config-line)#modem autoconfigure discovery R2_2081249(config-line)#^Z R2_2081249# R2_2081249# *Dec 6 14:58:26.039: %SYS-5-CONFIG_I: Configured from console by console *Dec 6 14:58:32.191: TTY1: Modem type is default *Dec 6 14:58:32.191: TTY1: Modem command: --AT&F&C1&D2S0=1H0-- *Dec 6 14:58:32.723: TTY1: Modem configuration succeeded *Dec 6 14:58:32.723: TTY1: Done with modem configuration R2_2081249# R2_2081249#SH line tty 1 Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int 1 TTY - inout - - - 0 0 0/0 - Line 1, Location: "", Type: "" Length: 24 lines, Width: 80 columns Status: Modem Detected, CTS Raised, 0x400000 Capabilities: Hardware Flowcontrol In, Hardware Flowcontrol Out Modem Callout, Modem RI is CD, Modem Discovery, Integrated Modem Get Modem Info Enabled Modem state: Idle Modem hardware state: CTS noDSR DTR RTS, Modem Configured Special Chars: Escape Hold Stop Start Disconnect Activation ^^x none - - none Timeouts: Idle EXEC Idle Session Modem Answer Session Dispatch 00:10:00 never none not set Idle Session Disconnect Warning never Login-sequence User Response 00:00:30 Autoselect Initial Wait not set Modem type is default. Session limit is not set. Time since activation: never Editing is enabled. History is enabled, history size is 20. DNS resolution in show commands is enabled Full user help is disabled Allowed input transports are pad telnet rlogin udptn ssh. Allowed output transports are pad telnet rlogin ssh. Preferred transport is telnet. No output characters are padded No special data dispatching characters