sh module Mod Slot Ports Module-Type Model Sub Status --- ---- ----- ------------------------- ------------------- --- -------- 1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok 2 2 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes standby 3 3 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok 4 4 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 5 5 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok 6 6 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok 7 7 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 8 8 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok 9 9 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok Mod Module-Name Serial-Num --- -------------------- ----------- 1 SAD042303TF 2 SAD042303HZ 3 SAD041905TV 4 SAL08239KDK 5 SAD041905LJ 6 SAD041905PW 7 SAL062517N2 8 SAL062720C0 9 SAL063242GR --More--         Mod MAC-Address(es) Hw Fw Sw --- -------------------------------------- ------ ---------- ----------------- 1 00-b0-8e-83-7e-a6 to 00-b0-8e-83-7e-a7 3.1 5.3(1) 7.6(3a) 00-b0-8e-83-7e-a4 to 00-b0-8e-83-7e-a5 00-0b-45-95-cc-00 to 00-0b-45-95-cf-ff 2 00-b0-c2-f5-a7-82 to 00-b0-c2-f5-a7-83 3.1 5.3(1) 7.6(3a) 00-b0-c2-f5-a7-80 to 00-b0-c2-f5-a7-81 3 00-01-97-15-b6-80 to 00-01-97-15-b6-af 1.2 5.1(1)CSX 7.6(3a) 4 00-11-21-b1-c3-e0 to 00-11-21-b1-c4-0f 8.1 5.4(2) 7.6(3a) 5 00-01-97-15-f6-a0 to 00-01-97-15-f6-cf 1.2 5.1(1)CSX 7.6(3a) 6 00-01-97-0e-38-d0 to 00-01-97-0e-38-ff 1.2 5.1(1)CSX 7.6(3a) 7 00-09-b7-93-98-54 to 00-09-b7-93-98-83 6.1 5.4(2) 7.6(3a) 8 00-09-b7-93-b5-d0 to 00-09-b7-93-b5-ff 6.1 5.4(2) 7.6(3a) 9 00-09-b7-93-b6-00 to 00-09-b7-93-b6-2f 6.1 5.4(2) 7.6(3a) Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw --- ----------------------- ------------------- ----------- ------ ------ 1 L3 Switching Engine WS-F6K-PFC SAD04230AJN 1.1 2 L3 Switching Engine WS-F6K-PFC SAD04230ABJ 1.1 4 Inline Power Module WS-F6K-VPWR 2.0 1.0 7 Inline Power Module WS-F6K-VPWR 1.0 1.0 8 Inline Power Module WS-F6K-VPWR 1.0 1.0 --More--        9 Inline Power Module WS-F6K-VPWR 1.0 1.0 ****************** show config ****************** This command shows non-default configurations only. Use 'show config all' to show both default and non-default configurations. ............... .......................... . begin ! # ***** NON-DEFAULT CONFIGURATION ***** ! ! #time: Fri Jul 18 2008, 17:20:50 ! #version 7.6(3a) ! ! #! #ip set interface sc0 1 10.10.10.1/255.255.255.0 10.10.10.255 set interface sc1 down set ip alias default 0.0.0.0 ! #set boot command set boot config-register 0x101 set boot system flash bootflash: ! # default port status is enable ! ! #module 1 : 2-port 1000BaseX Supervisor set udld enable 1/1 ! #module 2 : 2-port 1000BaseX Supervisor ! #module 3 : 48-port 10/100BaseTX Ethernet ! #module 4 : 48-port 10/100BaseTX Ethernet ! #module 5 : 48-port 10/100BaseTX Ethernet ! #module 6 : 48-port 10/100BaseTX Ethernet ! #module 7 : 48-port 10/100BaseTX Ethernet ! #module 8 : 48-port 10/100BaseTX Ethernet ! #module 9 : 48-port 10/100BaseTX Ethernet ! #module 15 empty ! #module 16 empty end Console> (enable)