em 02-25-2014 07:48 AM
Hello
I have a problem with my Cisco Aironet 1130G series, last time I try to upgrad the IOS but i put the wrong IOS and then i not be able to access to Flash or delete or write anything in my AP. pls i Need Help.
nv_done: unable to open "flash:/config.txt.new"
nv_done: unable to open "flash:/config.txt.new"
nv_done: unable to open "flash:/private-multiple-fs.new"[OK]
NVRAM Verification Failed
Proceed with reload? [confirm]
flash:/env_vars.tmp: No such deviceThe filesystem containing the variables may not be initialized yet.
*Mar 1 00:35:07.247: %SYS-5-RELOAD: Reload requested by console. Reload Reason: Reload Command.Xmodem file system is available.
flashfs[0]: 149 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 15998976
flashfs[0]: Bytes used: 5548544
flashfs[0]: Bytes available: 10450432
flashfs[0]: flashfs fsck took 28 seconds.
Base ethernet MAC Address: 44:d3:ca:e5:6a:84
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
link auto-negotiating....
auto-negotiation takes 10000 milli-seconds to complete
ERROR: timeout waiting for auto-negotiation to complete
ERROR: fail to bring ethernet link up
The system has been encountered an error initializing
ethernet port. You may need to check hardware
The system is ignoring the error and continuing boot.
If you interrupt the system boot process, the following
commands will reinitialize ethernet, tftp, and finish
loading the operating system software:
ether_init
tftp_init
boot
Loading "flash:/c1310-k9w7-tar.124-25d.JA2/c1310-k9w7-tar.124-25d.JA2.bin"...flash:/c1310-k9w7-tar.124-25d.JA2/c1310-k9w7-tar.124-25d.JA2.bin: no such file or directory
Error loading "flash:/c1310-k9w7-tar.124-25d.JA2/c1310-k9w7-tar.124-25d.JA2.bin"
Interrupt within 5 seconds to abort boot process.
Loading "flash:/c1310-k9w7-mx.124-25d.JA2/c1310-k9w7-mx.124-25d.JA2"...#########################################################################################################################################################################################################################################################################################################################################################################################################################################################################################
File "flash:/c1310-k9w7-mx.124-25d.JA2/c1310-k9w7-mx.124-25d.JA2" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1310 Software (C1310-K9W7-M), Version 12.4(25d)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 12-Sep-12 00:48 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
Unable to initialize flash device -- device not found.
...done Initializing flashfs.
flash:/env_vars.tmp: No such deviceThe filesystem containing the variables may not be initialized yet.
Radio0 present A506 7100 E8000000 A0000000 80000000 3
Unable to create Frequency bands, Channel / Max Power information not found
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
cisco AIR-AP1131G-E-K9 (PowerPCElvis) processor (revision A0) with 25590K/7168K bytes of memory.
Processor board ID FCZ1534Q0T7
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:D3:CA:E5:6A:84
Part Number : 73-11587-03
PCA Assembly Number : 800-30422-02
PCA Revision Number : A0
PCB Serial Number : FOC15311DAM
Top Assembly Part Number : 800-29578-02
Top Assembly Serial Number : FCZ1534Q0T7
Top Revision Number : A0
Product/Model Number : AIR-AP1131G-E-K9
Cisco IOS Software, C1310 Software (C1310-K9W7-M), Version 12.4(25d)JA2, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Wed 12-Sep-12 00:48 by prod_rel_team
ROM: Bootstrap program is C1310 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
ap uptime is 10 minutes
System returned to ROM by power-on
System image file is "flash:/c1310-k9w7-mx.124-25d.JA2/c1310-k9w7-mx.124-25d.JA2"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
cisco AIR-AP1131G-E-K9 (PowerPCElvis) processor (revision A0) with 25590K/7168K bytes of memory.
Processor board ID FCZ1534Q0T7
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:D3:CA:E5:6A:84
Part Number : 73-11587-03
PCA Assembly Number : 800-30422-02
PCA Revision Number : A0
PCB Serial Number : FOC15311DAM
Top Assembly Part Number : 800-29578-02
Top Assembly Serial Number : FCZ1534Q0T7
Top Revision Number : A0
Product/Model Number : AIR-AP1131G-E-K9
Configuration register is 0xF
ap#sh fla
ap#sh flash:
^
% Invalid input detected at '^' marker.
ap#del
ap#delete ?
/force Force delete
/recursive Recursive delete
nvram: File to be deleted
Unknown file system
p#sh inventory
NAME: "AP1130", DESCR: "Cisco Aironet 1130 Series (IEEE 802.11a/g) Access Point"
PID: AIR-AP1131G-E-K9 , VID: V02, SN: FCZ1534Q0T7
ap#sh ip interface brief
Interface IP-Address OK? Method Status Protocol
BVI1 unassigned YES DHCP down down
Dot11Radio0 unassigned YES unset administratively down down
FastEthernet0 unassigned YES other up down
ap#
thanks in advance
em 02-25-2014 01:05 PM
em 02-25-2014 11:10 PM
Hello Leo I can't make any modification in flash pls see a message below ap# ap#sh ip interface brief Interface IP-Address OK? Method Status Protocol BVI1 10.0.0.30 YES manual up up Dot11Radio0 unassigned YES unset administratively down down FastEthernet0 unassigned YES other up up ap# ap#ping 10.0.0.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/200/1000 ms ap# ap# ap# ap#cop ap#copy tf ap#copy tftp flash: ^ % Invalid input detected at '^' marker. ap# and when try to access to Rommon mode Ican't . regards
em 02-26-2014 12:19 AM
Menad,
You can't make modifications because your AP booted the wrong IOS. The IOS booted a controller-based IOS and you can't make any modifications.
The link I've posted above will show you the easiest method to load the correct IOS using the "Mode" button.
Encontre respostas, faça perguntas e conecte-se com nossa comunidade de especialistas da Cisco de todo o mundo.
Estamos felizes por você estar aqui! Participe de conversas e conecte-se com sua comunidade.
Navegue pelos links rápidos da Comunidade e usufrua de um conteúdo personalizado e em seu idioma nativo: