Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1942835members
1273470discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

C3850 Boot Variable

Silly question here.  I have a C3850 switch that I just upgraded to the most recent IOS.  When I reboot the switch it loads back into the previous version IOS.  How do I set the boot variable for this switch to boot to the current configuration? I ha...

CMack6 by • Level 1
  • 3448 Views
  • 9 replies
  • 0 Helpful votes

Help with a project

Basically  this is a small project that I have for school which I would like to solve and I've been out of my mind for the past 3 days because I can't seem to get it right.Im creating a small company  where I have some main offices and a room for gue...

Dus002 by • Level 1
  • 37 Views
  • 0 replies
  • 0 Helpful votes

Assistance Needed to Reconfigure ISP Router and Cisco Router

Hello Team,I currently have the following setup:An ISP router configured in bridge mode that provides internet to my Cisco router via LAN 4. Cisco router is configured with a DHCP server for IP addressing.I'd like to modify this configuration in orde...

Antonnifo by • Level 1
  • 88 Views
  • 3 replies
  • 0 Helpful votes

C9200 - SNMP traps including interface description

Hi, we have replaced several C2960 and C3560 with new C9200L switches running on IOS XE 17.9.5. I would like to have the switches to send out SNMP traps (preferable v3, but I would even be happy with v1/v2c) on interface status changes including the ...

Ethan-H by • Level 1
  • 173 Views
  • 1 replies
  • 0 Helpful votes

Resolved! c9800 Flex Connect Post Auth ACL Issue

I already have a TAC case open on this but I wanted to see if anyone else has run across this...I am deploying new c9800-40's and have a requirement to do flex connect with CWA. I had this set up with my 5520's and it worked without issue but for som...

xxkozxx by • Level 1
  • 2268 Views
  • 14 replies
  • 0 Helpful votes

Poor 5Ghz throughput - 9800 / 17.9.4a / 1800-series APs

Hi,Per the title, I've got an issue with 5Ghz clients that have good signal strength because they are sat almost underneath the AP (1832 APs) yet but struggling to get more than 1Mbps throughput.  I can see the channel utilisation is over 50% but zer...

Cisco Nexus 3000 Password Recovery

Hi everyone,I am trying to recover the console password of a Cisco Nexus 3000; however, for some weird reason, whatever I am trying is not working. Using CTRL + C, I am able login to the “switch(boot)#” The switch does not take the command “dir” I tr...

Flexconnect on Slow Links

Hi, We had a deployment of centralised WLC (earlier 3504) with flexconnect configured for remote sites (centralized auth, local switching, ISE CWA. ISE, WAPs and clients are on same LAN). These sites are connected to the controller using satellite li...

Bought a used ASA5585-X, can't get encryption PAK

Hi,I recently bought an end of life'd ASA5585-X SSP-20, and I'd like to get the free 3DES/AES encryption PAK, but the license portal always tells me it failed and to contact GLO.  Is this licensing portal just down for this particular option, or mayb...

WAP150 répéteur Wifi sans Ethernet

Bonjour,Je souhaite savoir s'il est possible de se passer de câble Ethernet branché au routeur, en connectant le routeur à la borne en wifi. Que la borne reçoive le réseau du routeur via le wifi et non par câble Ethernet.La borne est une WAP150.Merci...

Gerard67 by • Level 1
  • 33 Views
  • 0 replies
  • 0 Helpful votes

Error code 10 on dot11Radio interface

Hello , i have configure my Cisco Aironet Access point and the dot11Radio interface keeps restarted automatically with error code 10.i have already update the IOS image to the latest version , but still encounter the same problem . 

Cisco Secure access config guide

HI I plan to implement Cisco Secure access POC for a client. there is little material about this solution. is there any one with additional material that i can use. Thanks

BGP flapping with MTU mismatch

Hello Everyone, This is a typical issue but I want more details, in many cases when BGP flaps every 180 secs "Hold timer", when we adjust MTU the same at both sides, it works fine. But how could MTU affect the keepalive messages which are only 19 byt...

Load more