*Feb 28 20:30:05: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 20:30:05: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 20:30:06: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down System Bootstrap, Version 12.2(7r) [cmong 7r], RELEASE SOFTWARE (fc1) Copyright (c) 2002 by cisco Systems, Inc. C2600 platform with 32768 Kbytes of main memory program load complete, entry point: 0x80008000, size: 0x7570a4 Self decompressing the image : ############################################################################################################################# [OK] Smart Init is enabled smart init is sizing iomem ID MEMORY_REQ TYPE 00036D 0X00103980 C2621XM Dual Fast Ethernet 0X00098670 public buffer pools 0X00211000 public particle pools TOTAL: 0X003ACFF0 If any of the above Memory Requirements are "UNKNOWN", you may be using an unsupported configuration or there is a software problem and system operation may be compromised. Rounded IOMEM up to: 4Mb. Using 12 percent iomem. [4Mb/32Mb] Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software - Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.3(15), RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Tue 24-May-05 14:01 by ssearch Image text-base: 0x80008098, data-base: 0x80CD8A7C cisco 2621XM (MPC860P) processor (revision 0x100) with 28672K/4096K bytes of memory. Processor board ID JAD064202TK (3488772252) M860 processor: part number 5, mask 2 Bridging software. X.25 software, Version 3.0.0. Basic Rate ISDN software, Version 1.1. 2 FastEthernet/IEEE 802.3 interface(s) 1 ISDN Basic Rate interface(s) 32K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read/Write) Slot is empty or does not support clock participate WIC slot is empty or does not support clock participate  Press RETURN to get started! *Mar 1 00:00:08.435: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up *Mar 1 00:00:08.435: %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up *Feb 28 18:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down *Feb 28 18:00:09: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down *Feb 28 18:00:10: %SYS-5-CONFIG_I: Configured from memory by console *Feb 28 18:00:10: %LINK-3-UPDOWN: Interface BRI0/0, changed state to up *Feb 28 18:00:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:1, changed state to down *Feb 28 18:00:10: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2, changed state to down *Feb 28 18:00:11: %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to administratively down *Feb 28 18:00:12: %SYS-5-RESTART: System restarted -- Cisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.3(15), RELEASE SOFTW This is a HillARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2005 by cisco Systems, Inc. Compiled Tue 24-May-05 14:01 by ssearch *Feb 28 18:00:12: %SNMP-5-COLDSTART: SNMP agent on host New_Braunfels_DTC is undergoing a cold start *Feb 28 18:00:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up *Feb 28 18:00:14: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down *Feb 28 18:00:16: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up Country Community MHMR Center system restricted to official business and subject to being monitored at any time. Anyone using this system expressly consents to such monitoring and to any evidence of unauthorized access, use, or modification being used for criminal prosecution. New_Braunfels_DTC> *Feb 28 18:00:25: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0/0, TEI 104 changed to up *Feb 28 18:00:29: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:00:29: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:00:30: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down *Feb 28 18:00:34: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:00:34: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:00:34: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to downdebug *Feb 28 18:00:39: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:00:39: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:00:39: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to downisdn q *Feb 28 18:00:44: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:00:44: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A9 *Feb 28 18:00:44: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down31 ^ % Invalid input detected at '^' marker. New_Braunfels_DTC>en Password: *Feb 28 18:00:55: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:00:55: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:00:56: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down New_Braunfels_DTC# *Feb 28 18:01:02: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:01:02: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:01:02: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to downdebug isdn q931 debug isdn q931 is ON. New_Braunfels_DTC# *Feb 28 18:01:44: ISDN BR0/0 Q931: TX -> SETUP pd = 8 callref = 0x07 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0x83 Keypad Facility i = '6277092' *Feb 28 18:01:44: ISDN BR0/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x87 Channel ID i = 0x89 *Feb 28 18:01:48: ISDN BR0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x87 *Feb 28 18:01:48: ISDN BR0/0 Q931: RX <- CONNECT pd = 8 callref = 0x87 *Feb 28 18:01:48: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:01:48: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:01:48: ISDN BR0/0 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x07 *Feb 28 18:01:48: ISDN BR0/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x07 Cause i = 0x8090 - Normal call clearing *Feb 28 18:01:48: ISDN BR0/0 Q931: RX <- RELEASE pd = 8 callref = 0x87 *Feb 28 18:01:48: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down *Feb 28 18:01:48: ISDN BR0/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x07 *Feb 28 18:01:55: ISDN BR0/0 Q931: TX -> SETUP pd = 8 callref = 0x08 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0x83 Keypad Facility i = '6277092' *Feb 28 18:01:55: ISDN BR0/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x88 Channel ID i = 0x89 *Feb 28 18:01:59: ISDN BR0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x88 *Feb 28 18:01:59: ISDN BR0/0 Q931: RX <- CONNECT pd = 8 callref = 0x88 *Feb 28 18:01:59: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:01:59: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:01:59: ISDN BR0/0 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x08 *Feb 28 18:01:59: ISDN BR0/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x08 Cause i = 0x8090 - Normal call clearing *Feb 28 18:02:00: ISDN BR0/0 Q931: RX <- RELEASE pd = 8 callref = 0x88 *Feb 28 18:02:00: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down *Feb 28 18:02:00: ISDN BR0/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x08 *Feb 28 18:02:00: ISDN BR0/0 Q931: TX -> SETUP pd = 8 callref = 0x09 Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0x83 Keypad Facility i = '6277092' *Feb 28 18:02:00: ISDN BR0/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x89 Channel ID i = 0x89 *Feb 28 18:02:04: ISDN BR0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x89 *Feb 28 18:02:04: ISDN BR0/0 Q931: RX <- CONNECT pd = 8 callref = 0x89 *Feb 28 18:02:04: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:02:04: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:02:04: ISDN BR0/0 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x09 *Feb 28 18:02:04: ISDN BR0/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x09 Cause i = 0x8090 - Normal call clearing *Feb 28 18:02:04: ISDN BR0/0 Q931: RX <- RELEASE pd = 8 callref = 0x89 *Feb 28 18:02:04: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down *Feb 28 18:02:04: ISDN BR0/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x09 *Feb 28 18:02:09: ISDN BR0/0 Q931: TX -> SETUP pd = 8 callref = 0x0A Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0x83 Keypad Facility i = '6277092' *Feb 28 18:02:09: ISDN BR0/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x8A Channel ID i = 0x89 *Feb 28 18:02:13: ISDN BR0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x8A *Feb 28 18:02:13: ISDN BR0/0 Q931: RX <- CONNECT pd = 8 callref = 0x8A *Feb 28 18:02:13: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:02:13: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:02:13: ISDN BR0/0 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x0A *Feb 28 18:02:13: ISDN BR0/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x0A Cause i = 0x8090 - Normal call clearing *Feb 28 18:02:13: ISDN BR0/0 Q931: RX <- RELEASE pd = 8 callref = 0x8A *Feb 28 18:02:13: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down *Feb 28 18:02:13: ISDN BR0/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0Ano d *Feb 28 18:02:24: ISDN BR0/0 Q931: TX -> SETUP pd = 8 callref = 0x0B Bearer Capability i = 0x8890 Standard = CCITT Transfer Capability = Unrestricted Digital Transfer Mode = Circuit Transfer Rate = 64 kbit/s Channel ID i = 0x83 Keypad Facility i = '6277092' *Feb 28 18:02:24: ISDN BR0/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x8B Channel ID i = 0x89ebug % Type "debug ?" for a list of subcommands New_Braunfels_DTC# *Feb 28 18:02:28: ISDN BR0/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x8B *Feb 28 18:02:28: ISDN BR0/0 Q931: RX <- CONNECT pd = 8 callref = 0x8B *Feb 28 18:02:28: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up *Feb 28 18:02:28: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 6277092 N/A *Feb 28 18:02:28: ISDN BR0/0 Q931: TX -> CONNECT_ACK pd = 8 callref = 0x0B *Feb 28 18:02:28: ISDN BR0/0 Q931: TX -> DISCONNECT pd = 8 callref = 0x0B Cause i = 0x8090 - Normal call clearing *Feb 28 18:02:28: ISDN BR0/0 Q931: RX <- RELEASE pd = 8 callref = 0x8B *Feb 28 18:02:28: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down *Feb 28 18:02:28: ISDN BR0/0 Q931: TX -> RELEASE_COMP pd = 8 callref = 0x0Bno debug all All possible debugging has been turned off New_Braunfels_DTC#